From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S932099AbcBVNFC (ORCPT ); Mon, 22 Feb 2016 08:05:02 -0500 Received: from box2.japko.eu ([91.121.152.53]:45362 "EHLO box2.japko.eu" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1754893AbcBVNE6 (ORCPT ); Mon, 22 Feb 2016 08:04:58 -0500 From: Krzysztof Adamski To: Linus Walleij , Maxime Ripard , Chen-Yu Tsai , Hans de Goede , Lee Jones , Rob Herring , Jens Kuske , Fabian Frederick , Vishnu Patekar , linux-gpio@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-sunxi@googlegroups.com Cc: Krzysztof Adamski Subject: [PATCH v5 0/4] pinctrl: sunxi: Add H3 R_PIO controller support Date: Mon, 22 Feb 2016 14:03:24 +0100 Message-Id: <1456146208-13890-1-git-send-email-k@japko.eu> X-Mailer: git-send-email 2.1.4 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org This patch series is extension of my original single patch with the same subject. It adds support for R_PIO so that GPIO port L can be used in H3 based devices. It was tested on OrangePi PC and OrangePi Plus where PL is connected amount others to an onboard led, a switch, an IR receiver and some VCC controllers. Patchset is based on next-20160222. --- Changes since v4: - remove patches that are alredy merged - add patch describing leds and switch in DT Changes since v3: - collect some acked-bys - fix r_pios #interrupt-cells Changes since v2: - fixed apb0 parrent clocks list - moved binding documentation change to the proper patch - simplified sunxi_pinctrl_gpio_get according to ChenYu suggestions - fixed ordering in sunxi binding documentation Changes since v1: - splited patch to two separate - dtsi and c files - added APB0 clocks a parent for R_PIO - added fix in sunxi_pinctrl_gpio_get for getting pin value when in irq mode and on 2nd pinctrl - fixed a "pwn" > "pwm" typo - fixed order in allwinner,sunxi-pinctrl.txt Krzysztof Adamski (4): clk: sunxi: Add apb0 gates for H3 dts: sun8i-h3: Add APB0 related clocks and resets ARM: dts: sun8i-h3: Add R_PIO controller node to the dtsi ARM: dts: sun8i: Add leds and switch on Orangepi Plus boards Krzysztof Adamski (4): clk: sunxi: Add apb0 gates for H3 dts: sun8i-h3: Add APB0 related clocks and resets ARM: dts: sun8i-h3: Add R_PIO controller node to the dtsi ARM: dts: sun8i: Add leds and switch on Orangepi Plus boards Documentation/devicetree/bindings/clock/sunxi.txt | 2 + arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 63 +++++++++++++++++++++++ arch/arm/boot/dts/sun8i-h3.dtsi | 37 +++++++++++++ drivers/clk/sunxi/clk-simple-gates.c | 4 ++ 4 files changed, 106 insertions(+) -- 2.1.4