From: Andre Przywara <andre.przywara@arm.com>
To: Maxime Ripard <maxime.ripard@free-electrons.com>,
Chen-Yu Tsai <wens@csie.org>,
linux-sunxi@googlegroups.com
Cc: Arnd Bergmann <arnd@arndb.de>,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
Catalin Marinas <catalin.marinas@arm.com>,
Will Deacon <will.deacon@arm.com>,
Rob Herring <robh+dt@kernel.org>, Pawel Moll <pawel.moll@arm.com>,
Mark Rutland <mark.rutland@arm.com>,
Ian Campbell <ijc+devicetree@hellion.org.uk>,
Kumar Gala <galak@codeaurora.org>,
devicetree@vger.kernel.org
Subject: [PATCH v3 07/10] arm64: dts: add Allwinner A64 SoC .dtsi
Date: Mon, 22 Feb 2016 18:20:52 +0000 [thread overview]
Message-ID: <1456165255-31013-8-git-send-email-andre.przywara@arm.com> (raw)
In-Reply-To: <1456165255-31013-1-git-send-email-andre.przywara@arm.com>
The Allwinner A64 SoC is a low-cost chip with 4 ARM Cortex-A53 cores
and the typical tablet / TV box peripherals.
The SoC is based on the (32-bit) Allwinner H3 chip, sharing most of
the peripherals and the memory map.
Although the cores are proper 64-bit ones, the whole SoC is actually
limited to 4GB (including all the supported DRAM), so we use 32-bit
address and size cells. This has the nice feature of us being able to
reuse the DT for 32-bit kernels as well.
This .dtsi lists the hardware that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
Changelog v1 .. v2:
- remove compatible string from the .dtsi
- amend compatible names to include sun50i
- drop PSCI 0.1 compatibility
- use lowercase hex digits in the GIC node too
- make pll6x2 an explicit fixed-factor clock
- make pll8 and pll8x2 proper clocks
- amend MMC clocks to match the manual, they are now mod0 clocks
- adapt MMC nodes to new MMC clocks
- add separate 4-pin and 2-pin definitions for the UARTs
- add I2C pins and driver nodes
- switch ahb_rst node to use normal compatible name, not the special,
early-registration one.
Changelog v2 .. v3:
- remove leading zeros from node names' address part
- adapt PLL6/7/8 to proper PLL6 binding
- rename PLL6 to PLL7
Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
Documentation/devicetree/bindings/clock/sunxi.txt | 1 +
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 624 ++++++++++++++++++++++
3 files changed, 626 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
index 7e79fcc..7e59d8b 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.txt
+++ b/Documentation/devicetree/bindings/arm/sunxi.txt
@@ -14,3 +14,4 @@ using one of the following compatible strings:
allwinner,sun8i-a83t
allwinner,sun8i-h3
allwinner,sun9i-a80
+ allwinner,sun50i-a64
diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 323af8e..b7bd40d 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -80,6 +80,7 @@ Required properties:
"allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80
"allwinner,sun4i-a10-ve-clk" - for the Video Engine clock
"allwinner,sunxi-multi-bus-gates-clk" - for the multi-parent bus gates
+ "allwinner,sun50i-a64-bus-gates-clk" - for the bus gates on A64
Required properties for all clocks:
- reg : shall be the control register address for the clock.
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
new file mode 100644
index 0000000..fb9c509
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -0,0 +1,624 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ * based on the Allwinner H3 dtsi:
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x40000000 0>;
+ };
+
+ gic: interrupt-controller@1c81000 {
+ compatible = "arm,gic-400";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupts = <GIC_PPI 9
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ pll1: pll1_clk@1c20000 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-a23-pll1-clk";
+ reg = <0x01c20000 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll1";
+ };
+
+ pll6: pll6_clk@1c20028 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun6i-a31-pll6-clk";
+ reg = <0x01c20028 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll6", "pll6x2";
+ };
+
+ pll6d2: pll6d2_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clock-div = <2>;
+ clock-mult = <1>;
+ clocks = <&pll6 0>;
+ clock-output-names = "pll6d2";
+ };
+
+ pll7: pll7_clk@1c2002c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun6i-a31-pll6-clk";
+ reg = <0x01c2002c 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll7", "pll7x2";
+ };
+
+ cpu: cpu_clk@1c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-cpu-clk";
+ reg = <0x01c20050 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
+ clock-output-names = "cpu";
+ critical-clocks = <0>;
+ };
+
+ axi: axi_clk@1c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-axi-clk";
+ reg = <0x01c20050 0x4>;
+ clocks = <&cpu>;
+ clock-output-names = "axi";
+ };
+
+ ahb1: ahb1_clk@1c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun6i-a31-ahb1-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
+ clock-output-names = "ahb1";
+ };
+
+ ahb2: ahb2_clk@1c2005c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-h3-ahb2-clk";
+ reg = <0x01c2005c 0x4>;
+ clocks = <&ahb1>, <&pll6d2>;
+ clock-output-names = "ahb2";
+ };
+
+ apb1: apb1_clk@1c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb0-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&ahb1>;
+ clock-output-names = "apb1";
+ };
+
+ apb2: apb2_clk@1c20058 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb1-clk";
+ reg = <0x01c20058 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll6 1>, <&pll6 1>;
+ clock-output-names = "apb2";
+ };
+
+ bus_gates: bus_gates_clk@1c20060 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun50i-a64-bus-gates-clk",
+ "allwinner,sunxi-multi-bus-gates-clk";
+ reg = <0x01c20060 0x14>;
+ ahb1_parent {
+ clocks = <&ahb1>;
+ clock-indices = <1>, <5>,
+ <6>, <8>,
+ <9>, <10>,
+ <13>, <14>,
+ <18>, <19>,
+ <20>, <21>,
+ <23>, <24>,
+ <25>, <28>,
+ <32>, <35>,
+ <36>, <37>,
+ <40>, <43>,
+ <44>, <52>,
+ <53>, <54>,
+ <135>;
+ clock-output-names = "bus_mipidsi", "bus_ce",
+ "bus_dma", "bus_mmc0",
+ "bus_mmc1", "bus_mmc2",
+ "bus_nand", "bus_sdram",
+ "bus_ts", "bus_hstimer",
+ "bus_spi0", "bus_spi1",
+ "bus_otg", "bus_otg_ehci0",
+ "bus_ehci0", "bus_otg_ohci0",
+ "bus_ve", "bus_lcd0",
+ "bus_lcd1", "bus_deint",
+ "bus_csi", "bus_hdmi",
+ "bus_de", "bus_gpu",
+ "bus_msgbox", "bus_spinlock",
+ "bus_dbg";
+ };
+ ahb2_parent {
+ clocks = <&ahb2>;
+ clock-indices = <17>, <29>;
+ clock-output-names = "bus_gmac", "bus_ohci0";
+ };
+ apb1_parent {
+ clocks = <&apb1>;
+ clock-indices = <64>, <65>,
+ <69>, <72>,
+ <76>, <77>,
+ <78>;
+ clock-output-names = "bus_codec", "bus_spdif",
+ "bus_pio", "bus_ths",
+ "bus_i2s0", "bus_i2s1",
+ "bus_i2s2";
+ };
+ abp2_parent {
+ clocks = <&apb2>;
+ clock-indices = <96>, <97>,
+ <98>, <101>,
+ <112>, <113>,
+ <114>, <115>,
+ <116>;
+ clock-output-names = "bus_i2c0", "bus_i2c1",
+ "bus_i2c2", "bus_scr",
+ "bus_uart0", "bus_uart1",
+ "bus_uart2", "bus_uart3",
+ "bus_uart4";
+ };
+ };
+
+ mmc0_clk: mmc0_clk@1c20088 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c20088 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll7 1>;
+ clock-output-names = "mmc0";
+ };
+
+ mmc1_clk: mmc1_clk@1c2008c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c2008c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll7 1>;
+ clock-output-names = "mmc1";
+ };
+
+ mmc2_clk: mmc2_clk@1c20090 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c20090 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll7 1>;
+ clock-output-names = "mmc2";
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mmc0: mmc@1c0f000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&bus_gates 8>, <&mmc0_clk>,
+ <&mmc0_clk>, <&mmc0_clk>;
+ clock-names = "ahb", "mmc",
+ "output", "sample";
+ resets = <&ahb_rst 8>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@1c10000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&bus_gates 9>, <&mmc1_clk>,
+ <&mmc1_clk>, <&mmc1_clk>;
+ clock-names = "ahb", "mmc",
+ "output", "sample";
+ resets = <&ahb_rst 9>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@1c11000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&bus_gates 10>, <&mmc2_clk>,
+ <&mmc2_clk>, <&mmc2_clk>;
+ clock-names = "ahb", "mmc",
+ "output", "sample";
+ resets = <&ahb_rst 10>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pio: pinctrl@1c20800 {
+ compatible = "allwinner,sun50i-a64-pinctrl";
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bus_gates 69>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PB8", "PB9";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart0_pins_b: uart0@1 {
+ allwinner,pins = "PF2", "PF3";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart1_2pins: uart1_2@0 {
+ allwinner,pins = "PG6", "PG7";
+ allwinner,function = "uart1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart1_4pins: uart1_4@0 {
+ allwinner,pins = "PG6", "PG7", "PG8", "PG9";
+ allwinner,function = "uart1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart2_2pins: uart2_2@0 {
+ allwinner,pins = "PB0", "PB1";
+ allwinner,function = "uart2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart2_4pins: uart2_4@0 {
+ allwinner,pins = "PB0", "PB1", "PB2", "PB3";
+ allwinner,function = "uart2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart3_pins_a: uart3@0 {
+ allwinner,pins = "PD0", "PD1";
+ allwinner,function = "uart3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart3_2pins_b: uart3_2@1 {
+ allwinner,pins = "PH4", "PH5";
+ allwinner,function = "uart3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart3_4pins_b: uart3_4@1 {
+ allwinner,pins = "PH4", "PH5", "PH6", "PH7";
+ allwinner,function = "uart3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart4_2pins: uart4_2@0 {
+ allwinner,pins = "PD2", "PD3";
+ allwinner,function = "uart4";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart4_4pins: uart4_4@0 {
+ allwinner,pins = "PD2", "PD3", "PD4", "PD5";
+ allwinner,function = "uart4";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_pins: mmc0@0 {
+ allwinner,pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_default_cd_pin: mmc0_cd_pin@0 {
+ allwinner,pins = "PF6";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc1_pins: mmc1@0 {
+ allwinner,pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ allwinner,function = "mmc1";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc2_pins: mmc2@0 {
+ allwinner,pins = "PC1", "PC5", "PC6", "PC8",
+ "PC9", "PC10";
+ allwinner,function = "mmc2";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c0_pins: i2c0_pins {
+ allwinner,pins = "PH0", "PH1";
+ allwinner,function = "i2c0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c1_pins: i2c1_pins {
+ allwinner,pins = "PH2", "PH3";
+ allwinner,function = "i2c1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c2_pins: i2c2_pins {
+ allwinner,pins = "PE14", "PE15";
+ allwinner,function = "i2c2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
+
+ ahb_rst: reset@1c202c0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202c0 0xc>;
+ };
+
+ apb1_rst: reset@1c202d0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d0 0x4>;
+ };
+
+ apb2_rst: reset@1c202d8 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d8 0x4>;
+ };
+
+ uart0: serial@1c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 112>;
+ resets = <&apb2_rst 16>;
+ status = "disabled";
+ };
+
+ uart1: serial@1c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 113>;
+ resets = <&apb2_rst 17>;
+ status = "disabled";
+ };
+
+ uart2: serial@1c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 114>;
+ resets = <&apb2_rst 18>;
+ status = "disabled";
+ };
+
+ uart3: serial@1c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 115>;
+ resets = <&apb2_rst 19>;
+ status = "disabled";
+ };
+
+ uart4: serial@1c29000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29000 0x400>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 116>;
+ resets = <&apb2_rst 20>;
+ status = "disabled";
+ };
+
+ rtc: rtc@1f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x54>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ i2c0: i2c@1c2ac00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bus_gates 96>;
+ resets = <&apb2_rst 0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@1c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bus_gates 97>;
+ resets = <&apb2_rst 1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@1c2b400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bus_gates 98>;
+ resets = <&apb2_rst 2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
--
2.6.4
next prev parent reply other threads:[~2016-02-22 18:21 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-02-22 18:20 [PATCH v3 00/10] arm64: Introduce Allwinner A64 and Pine64 support Andre Przywara
2016-02-22 18:20 ` Andre Przywara
2016-02-22 18:20 ` [PATCH v3 02/10] ARM: dts: sunxi: make PLL8 in the H3 a proper clock Andre Przywara
2016-02-22 18:20 ` [PATCH v3 03/10] arm64: Introduce Allwinner SoC config option Andre Przywara
2016-02-22 18:20 ` [PATCH v3 04/10] drivers: pinctrl: add driver for Allwinner A64 SoC Andre Przywara
2016-02-25 18:49 ` Maxime Ripard
2016-03-07 3:33 ` Linus Walleij
2016-02-22 18:20 ` [PATCH v3 05/10] DT: clk: sunxi: add binding doc for the multi-bus-gates clock Andre Przywara
2016-02-22 18:20 ` [PATCH v3 06/10] clk: sunxi: add generic multi-parent bus clock gates driver Andre Przywara
2016-02-22 18:20 ` Andre Przywara [this message]
2016-02-22 18:20 ` [PATCH v3 08/10] of: add vendor prefix for Pine64 Andre Przywara
2016-02-22 18:20 ` [PATCH v3 09/10] arm64: dts: add Pine64 support Andre Przywara
2016-02-22 18:20 ` [PATCH v3 10/10] arm64: add defconfig options for Allwinner SoCs Andre Przywara
2016-02-25 18:52 ` Maxime Ripard
2016-02-25 10:04 ` [PATCH v3 00/10] arm64: Introduce Allwinner A64 and Pine64 support Andre Przywara
2016-02-25 19:25 ` Maxime Ripard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1456165255-31013-8-git-send-email-andre.przywara@arm.com \
--to=andre.przywara@arm.com \
--cc=arnd@arndb.de \
--cc=catalin.marinas@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@free-electrons.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
--cc=wens@csie.org \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome