From: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
To: Dmitry Torokhov <dmitry.torokhov@gmail.com>,
Russell King <linux@arm.linux.org.uk>,
Rob Herring <robh+dt@kernel.org>, Arnd Bergmann <arnd@arndb.de>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-input@vger.kernel.org
Cc: Pawel Moll <pawel.moll@arm.com>,
Mark Rutland <mark.rutland@arm.com>,
Ian Campbell <ijc+devicetree@hellion.org.uk>,
Kumar Gala <galak@codeaurora.org>,
Jonathan Richardson <jonathar@broadcom.com>,
Jon Mason <jonmason@broadcom.com>,
Florian Fainelli <f.fainelli@gmail.com>,
Anup Patel <anup.patel@broadcom.com>, Ray Jui <rjui@broadcom.com>,
Scott Branden <sbranden@broadcom.com>,
linux-kernel@vger.kernel.org,
bcm-kernel-feedback-list@broadcom.com,
Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Subject: [PATCH v4 2/3] input: syscon support in bcm_iproc_tsc driver
Date: Sat, 27 Feb 2016 12:29:55 +0530 [thread overview]
Message-ID: <1456556396-4759-3-git-send-email-raveendra.padasalagi@broadcom.com> (raw)
In-Reply-To: <1456556396-4759-1-git-send-email-raveendra.padasalagi@broadcom.com>
In Cygnus SOC touch screen controller registers are shared
with ADC and flex timer. Using readl/writel could lead to
race condition. So touch screen driver is enhanced to support
register access using syscon framework API's to take care of
mutually exclusive access.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
---
drivers/input/touchscreen/bcm_iproc_tsc.c | 79 +++++++++++++++++--------------
1 file changed, 44 insertions(+), 35 deletions(-)
diff --git a/drivers/input/touchscreen/bcm_iproc_tsc.c b/drivers/input/touchscreen/bcm_iproc_tsc.c
index ae460a5c..9957587 100644
--- a/drivers/input/touchscreen/bcm_iproc_tsc.c
+++ b/drivers/input/touchscreen/bcm_iproc_tsc.c
@@ -23,6 +23,8 @@
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/serio.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
#define IPROC_TS_NAME "iproc-ts"
@@ -88,7 +90,11 @@
#define TS_WIRE_MODE_BIT BIT(1)
#define dbg_reg(dev, priv, reg) \
- dev_dbg(dev, "%20s= 0x%08x\n", #reg, readl((priv)->regs + reg))
+do { \
+ u32 val; \
+ regmap_read(priv->regmap, reg, &val); \
+ dev_dbg(dev, "%20s= 0x%08x\n", #reg, val); \
+} while (0)
struct tsc_param {
/* Each step is 1024 us. Valid 1-256 */
@@ -141,7 +147,7 @@ struct iproc_ts_priv {
struct platform_device *pdev;
struct input_dev *idev;
- void __iomem *regs;
+ struct regmap *regmap;
struct clk *tsc_clk;
int pen_status;
@@ -196,22 +202,22 @@ static irqreturn_t iproc_touchscreen_interrupt(int irq, void *data)
int i;
bool needs_sync = false;
- intr_status = readl(priv->regs + INTERRUPT_STATUS);
- intr_status &= TS_PEN_INTR_MASK | TS_FIFO_INTR_MASK;
+ regmap_read(priv->regmap, INTERRUPT_STATUS, &intr_status);
+ intr_status &= (TS_PEN_INTR_MASK | TS_FIFO_INTR_MASK);
if (intr_status == 0)
return IRQ_NONE;
/* Clear all interrupt status bits, write-1-clear */
- writel(intr_status, priv->regs + INTERRUPT_STATUS);
-
+ regmap_write(priv->regmap, INTERRUPT_STATUS, intr_status);
/* Pen up/down */
if (intr_status & TS_PEN_INTR_MASK) {
- if (readl(priv->regs + CONTROLLER_STATUS) & TS_PEN_DOWN)
+ regmap_read(priv->regmap, CONTROLLER_STATUS, &priv->pen_status);
+ if (priv->pen_status & TS_PEN_DOWN)
priv->pen_status = PEN_DOWN_STATUS;
else
priv->pen_status = PEN_UP_STATUS;
- input_report_key(priv->idev, BTN_TOUCH, priv->pen_status);
+ input_report_key(priv->idev, BTN_TOUCH, priv->pen_status);
needs_sync = true;
dev_dbg(&priv->pdev->dev,
@@ -221,7 +227,7 @@ static irqreturn_t iproc_touchscreen_interrupt(int irq, void *data)
/* coordinates in FIFO exceed the theshold */
if (intr_status & TS_FIFO_INTR_MASK) {
for (i = 0; i < priv->cfg_params.fifo_threshold; i++) {
- raw_coordinate = readl(priv->regs + FIFO_DATA);
+ regmap_read(priv->regmap, FIFO_DATA, &raw_coordinate);
if (raw_coordinate == INVALID_COORD)
continue;
@@ -239,7 +245,7 @@ static irqreturn_t iproc_touchscreen_interrupt(int irq, void *data)
x = (x >> 4) & 0x0FFF;
y = (y >> 4) & 0x0FFF;
- /* adjust x y according to lcd tsc mount angle */
+ /* Adjust x y according to LCD tsc mount angle. */
if (priv->cfg_params.invert_x)
x = priv->cfg_params.max_x - x;
@@ -262,9 +268,10 @@ static irqreturn_t iproc_touchscreen_interrupt(int irq, void *data)
static int iproc_ts_start(struct input_dev *idev)
{
- struct iproc_ts_priv *priv = input_get_drvdata(idev);
u32 val;
+ u32 mask;
int error;
+ struct iproc_ts_priv *priv = input_get_drvdata(idev);
/* Enable clock */
error = clk_prepare_enable(priv->tsc_clk);
@@ -279,9 +286,10 @@ static int iproc_ts_start(struct input_dev *idev)
* FIFO reaches the int_th value, and pen event(up/down)
*/
val = TS_PEN_INTR_MASK | TS_FIFO_INTR_MASK;
- writel(val, priv->regs + INTERRUPT_MASK);
+ regmap_update_bits(priv->regmap, INTERRUPT_MASK, val, val);
- writel(priv->cfg_params.fifo_threshold, priv->regs + INTERRUPT_THRES);
+ val = priv->cfg_params.fifo_threshold;
+ regmap_write(priv->regmap, INTERRUPT_THRES, val);
/* Initialize control reg1 */
val = 0;
@@ -289,26 +297,23 @@ static int iproc_ts_start(struct input_dev *idev)
val |= priv->cfg_params.debounce_timeout << DEBOUNCE_TIMEOUT_SHIFT;
val |= priv->cfg_params.settling_timeout << SETTLING_TIMEOUT_SHIFT;
val |= priv->cfg_params.touch_timeout << TOUCH_TIMEOUT_SHIFT;
- writel(val, priv->regs + REGCTL1);
+ regmap_write(priv->regmap, REGCTL1, val);
/* Try to clear all interrupt status */
- val = readl(priv->regs + INTERRUPT_STATUS);
- val |= TS_FIFO_INTR_MASK | TS_PEN_INTR_MASK;
- writel(val, priv->regs + INTERRUPT_STATUS);
+ val = TS_FIFO_INTR_MASK | TS_PEN_INTR_MASK;
+ regmap_update_bits(priv->regmap, INTERRUPT_STATUS, val, val);
/* Initialize control reg2 */
- val = readl(priv->regs + REGCTL2);
- val |= TS_CONTROLLER_EN_BIT | TS_WIRE_MODE_BIT;
-
- val &= ~TS_CONTROLLER_AVGDATA_MASK;
+ val = TS_CONTROLLER_EN_BIT | TS_WIRE_MODE_BIT;
val |= priv->cfg_params.average_data << TS_CONTROLLER_AVGDATA_SHIFT;
- val &= ~(TS_CONTROLLER_PWR_LDO | /* PWR up LDO */
+ mask = (TS_CONTROLLER_AVGDATA_MASK);
+ mask |= (TS_CONTROLLER_PWR_LDO | /* PWR up LDO */
TS_CONTROLLER_PWR_ADC | /* PWR up ADC */
TS_CONTROLLER_PWR_BGP | /* PWR up BGP */
TS_CONTROLLER_PWR_TS); /* PWR up TS */
-
- writel(val, priv->regs + REGCTL2);
+ mask |= val;
+ regmap_update_bits(priv->regmap, REGCTL2, mask, val);
ts_reg_dump(priv);
@@ -320,12 +325,17 @@ static void iproc_ts_stop(struct input_dev *dev)
u32 val;
struct iproc_ts_priv *priv = input_get_drvdata(dev);
- writel(0, priv->regs + INTERRUPT_MASK); /* Disable all interrupts */
+ /*
+ * Disable FIFO int_th and pen event(up/down)Interrupts only
+ * as the interrupt mask register is shared between ADC, TS and
+ * flextimer.
+ */
+ val = TS_PEN_INTR_MASK | TS_FIFO_INTR_MASK;
+ regmap_update_bits(priv->regmap, INTERRUPT_MASK, val, 0);
/* Only power down touch screen controller */
- val = readl(priv->regs + REGCTL2);
- val |= TS_CONTROLLER_PWR_TS;
- writel(val, priv->regs + REGCTL2);
+ val = TS_CONTROLLER_PWR_TS;
+ regmap_update_bits(priv->regmap, REGCTL2, val, val);
clk_disable(priv->tsc_clk);
}
@@ -414,7 +424,6 @@ static int iproc_ts_probe(struct platform_device *pdev)
{
struct iproc_ts_priv *priv;
struct input_dev *idev;
- struct resource *res;
int irq;
int error;
@@ -422,12 +431,12 @@ static int iproc_ts_probe(struct platform_device *pdev)
if (!priv)
return -ENOMEM;
- /* touchscreen controller memory mapped regs */
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- priv->regs = devm_ioremap_resource(&pdev->dev, res);
- if (IS_ERR(priv->regs)) {
- error = PTR_ERR(priv->regs);
- dev_err(&pdev->dev, "unable to map I/O memory: %d\n", error);
+ /* touchscreen controller memory mapped regs via syscon*/
+ priv->regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+ "ts_syscon");
+ if (IS_ERR(priv->regmap)) {
+ error = PTR_ERR(priv->regmap);
+ dev_err(&pdev->dev, "unable to map I/O memory:%d\n", error);
return error;
}
--
1.9.1
next prev parent reply other threads:[~2016-02-27 7:00 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-02-27 6:59 [PATCH v4 0/3] Syscon support for iProc touchscreen driver Raveendra Padasalagi
2016-02-27 6:59 ` [PATCH v4 1/3] input: cygnus-update touchscreen dt node document Raveendra Padasalagi
2016-03-03 22:04 ` Rob Herring
2016-02-27 6:59 ` Raveendra Padasalagi [this message]
2016-02-27 6:59 ` [PATCH v4 3/3] ARM: dts: use syscon in cygnus touchscreen dt node Raveendra Padasalagi
2016-04-06 17:31 ` Dmitry Torokhov
2016-04-06 20:25 ` Florian Fainelli
2016-05-05 5:47 ` Raveendra Padasalagi
2016-05-05 18:44 ` Dmitry Torokhov
2016-03-16 6:23 ` [PATCH v4 0/3] Syscon support for iProc touchscreen driver Raveendra Padasalagi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1456556396-4759-3-git-send-email-raveendra.padasalagi@broadcom.com \
--to=raveendra.padasalagi@broadcom.com \
--cc=anup.patel@broadcom.com \
--cc=arnd@arndb.de \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.torokhov@gmail.com \
--cc=f.fainelli@gmail.com \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=jonathar@broadcom.com \
--cc=jonmason@broadcom.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
--cc=mark.rutland@arm.com \
--cc=pawel.moll@arm.com \
--cc=rjui@broadcom.com \
--cc=robh+dt@kernel.org \
--cc=sbranden@broadcom.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®