[RFC PATCH v2 1/2] [media] tvp5150: Add input connectors DT bindings

[Javier Martinez Canillas <javier@osg.samsung.com>]

The tvp5150 and tvp5151 decoders support different video input source
connections to their AIP1A and AIP1B pins. Either two Composite or a
S-Video input signals are supported.

The possible configurations are as follows:

- Analog Composite signal connected to AIP1A.
- Analog Composite signal connected to AIP1B.
- Analog S-Video Y (luminance) and C (chrominance)
  signals connected to AIP1A and AIP1B respectively.

This patch extends the Device Tree binding documentation to describe
how the input connectors for these devices should be defined in a DT.

Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>

---
Hello,

The DT binding assumes that there is a 1:1 map between physical connectors
and connections, so there will be a connector described in the DT for each
connection.

There is also the question about how the DT bindings will be extended to
support other attributes (color/position/group) using the properties API.

But I believe that can be done as a follow-up, once the properties API is
in mainline.

Best regards,
Javier

Changes in v2:
- Remove from the changelog a mention of devices that multiplex the
  physical RCA connectors to be used for the S-Video Y and C signals
  since it's a special case and it doesn't really work on the IGEPv2.

 .../devicetree/bindings/media/i2c/tvp5150.txt      | 59 ++++++++++++++++++++++
 1 file changed, 59 insertions(+)

diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
index 8c0fc1a26bf0..df555650b0b4 100644
--- a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
+++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
@@ -26,8 +26,46 @@ Required Endpoint Properties for parallel synchronization:
 If none of hsync-active, vsync-active and field-even-active is specified,
 the endpoint is assumed to use embedded BT.656 synchronization.
 
+-Optional nodes:
+- connectors: The list of tvp5150 input connectors available on a given
+  board. The node should contain a child 'port' node for each connector.
+
+  The tvp5150 has support for three possible connectors: 2 Composite and
+  1 S-video. The "reg" property is used to specify which input connector
+  is associated with each 'port', using the following possible values:
+
+  0: Composite0
+  1: Composite1
+  2: S-Video
+
+  The ports should have an endpoint subnode that is linked to a connector
+  node defined in Documentation/devicetree/bindings/display/connector/.
+  The linked connector compatible string should match the connector type.
+
 Example:
 
+composite0: connector@0 {
+	compatible = "composite-video-connector";
+	label = "Composite0";
+
+	port {
+		comp0_out: endpoint {
+			remote-endpoint = <&tvp5150_comp0_in>;
+		};
+	};
+};
+
+svideo: connector@1 {
+	compatible = "composite-video-connector";
+	label = "S-Video";
+
+	port {
+		svideo_out: endpoint {
+			remote-endpoint = <&tvp5150_svideo_in>;
+		};
+	};
+};
+
 &i2c2 {
 	...
 	tvp5150@5c {
@@ -36,6 +74,27 @@ Example:
 		pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
 		reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
 
+		connectors {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* Composite0 input */
+			port@0 {
+				reg = <0>;
+				tvp5150_comp0_in: endpoint {
+					remote-endpoint = <&comp0_out>;
+				};
+			};
+
+			/* S-Video input */
+			port@2 {
+				reg = <2>;
+				tvp5150_svideo_in: endpoint {
+					remote-endpoint = <&svideo_out>;
+				};
+			};
+		};
+
 		port {
 			tvp5150_1: endpoint {
 				remote-endpoint = <&ccdc_ep>;
-- 
2.5.5