From: Laxman Dewangan <ldewangan@nvidia.com>
To: <swarren@wwwdotorg.org>, <linus.walleij@linaro.org>,
<gnurou@gmail.com>, <robh+dt@kernel.org>, <mark.rutland@arm.com>,
<jonathanh@nvidia.com>, <thierry.reding@gmail.com>
Cc: <linux-tegra@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <linux-gpio@vger.kernel.org>,
Laxman Dewangan <ldewangan@nvidia.com>
Subject: [PATCH 6/6] pinctrl: tegra: Add driver to configure voltage and power state of io pads
Date: Mon, 2 May 2016 17:47:14 +0530 [thread overview]
Message-ID: <1462191434-28933-7-git-send-email-ldewangan@nvidia.com> (raw)
In-Reply-To: <1462191434-28933-1-git-send-email-ldewangan@nvidia.com>
NVIDIA Tegra210 supports the IO pads which can operate at 1.8V
or 3.3V I/O voltage levels. Also the IO pads can be configured
for power down state if it is not used. SW needs to configure the
voltage level of IO pads based on IO rail voltage and its power
state based on platform usage.
The voltage and power state configurations of pads are provided
through pin control frameworks. Add pin control driver for Tegra's
IO pads' voltage and power state configurations.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes from V1:
- Use the generic pincontrol property for low power enable/disable.
- sync with latest and remove all MODULE* macros
- Use renamed APIs form PMC
---
drivers/pinctrl/tegra/Makefile | 1 +
drivers/pinctrl/tegra/pinctrl-tegra210-io-pad.c | 301 ++++++++++++++++++++++++
2 files changed, 302 insertions(+)
create mode 100644 drivers/pinctrl/tegra/pinctrl-tegra210-io-pad.c
diff --git a/drivers/pinctrl/tegra/Makefile b/drivers/pinctrl/tegra/Makefile
index a927379..8c4519f 100644
--- a/drivers/pinctrl/tegra/Makefile
+++ b/drivers/pinctrl/tegra/Makefile
@@ -4,4 +4,5 @@ obj-$(CONFIG_PINCTRL_TEGRA30) += pinctrl-tegra30.o
obj-$(CONFIG_PINCTRL_TEGRA114) += pinctrl-tegra114.o
obj-$(CONFIG_PINCTRL_TEGRA124) += pinctrl-tegra124.o
obj-$(CONFIG_PINCTRL_TEGRA210) += pinctrl-tegra210.o
+obj-$(CONFIG_PINCTRL_TEGRA210) += pinctrl-tegra210-io-pad.o
obj-$(CONFIG_PINCTRL_TEGRA_XUSB) += pinctrl-tegra-xusb.o
diff --git a/drivers/pinctrl/tegra/pinctrl-tegra210-io-pad.c b/drivers/pinctrl/tegra/pinctrl-tegra210-io-pad.c
new file mode 100644
index 0000000..ab06c71
--- /dev/null
+++ b/drivers/pinctrl/tegra/pinctrl-tegra210-io-pad.c
@@ -0,0 +1,301 @@
+/*
+ * Generic ADC thermal driver
+ *
+ * Copyright (C) 2016 NVIDIA CORPORATION. All rights reserved.
+ *
+ * Author: Laxman Dewangan <ldewangan@nvidia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <soc/tegra/pmc.h>
+
+#include "../core.h"
+#include "../pinconf.h"
+#include "../pinctrl-utils.h"
+
+enum tegra_io_rail_pads_params {
+ TEGRA_IO_PAD_POWER_SOURCE_VOLTAGE = PIN_CONFIG_END + 1,
+};
+
+static const struct pinconf_generic_params tegra_io_pads_cfg_params[] = {
+ {
+ .property = "nvidia,power-source-voltage",
+ .param = TEGRA_IO_PAD_POWER_SOURCE_VOLTAGE,
+ },
+};
+
+struct tegra_io_pads_cfg_info {
+ const char *name;
+ const unsigned int pins[1];
+ int pad_id;
+ bool voltage_can_change;
+ bool support_low_power_state;
+};
+
+#define TEGRA210_PAD_INFO_TABLE(_entry_) \
+ _entry_(0, "audio", AUDIO, true, false), \
+ _entry_(1, "audio-hv", AUDIO_HV, true, true), \
+ _entry_(2, "cam", CAM, true, false), \
+ _entry_(3, "csia", CSIA, true, false), \
+ _entry_(4, "csib", CSIB, true, false), \
+ _entry_(5, "csic", CSIC, true, false), \
+ _entry_(6, "csid", CSID, true, false), \
+ _entry_(7, "csie", CSIE, true, false), \
+ _entry_(8, "csif", CSIF, true, false), \
+ _entry_(9, "dbg", DBG, true, false), \
+ _entry_(10, "debug-nonao", DEBUG_NONAO, true, false), \
+ _entry_(11, "dmic", DMIC, true, false), \
+ _entry_(12, "dp", DP, true, false), \
+ _entry_(13, "dsi", DSI, true, false), \
+ _entry_(14, "dsib", DSIB, true, false), \
+ _entry_(15, "dsic", DSIC, true, false), \
+ _entry_(16, "dsid", DSID, true, false), \
+ _entry_(17, "emmc", SDMMC4, true, false), \
+ _entry_(18, "emmc2", EMMC2, true, false), \
+ _entry_(19, "gpio", GPIO, true, true), \
+ _entry_(20, "hdmi", HDMI, true, false), \
+ _entry_(21, "hsic", HSIC, true, false), \
+ _entry_(22, "lvds", LVDS, true, false), \
+ _entry_(23, "mipi-bias", MIPI_BIAS, true, false), \
+ _entry_(24, "pex-bias", PEX_BIAS, true, false), \
+ _entry_(25, "pex-clk1", PEX_CLK1, true, false), \
+ _entry_(26, "pex-clk2", PEX_CLK2, true, false), \
+ _entry_(27, "pex-ctrl", PEX_CNTRL, true, false), \
+ _entry_(28, "sdmmc1", SDMMC1, true, true), \
+ _entry_(29, "sdmmc3", SDMMC3, true, true), \
+ _entry_(30, "spi", SPI, true, false), \
+ _entry_(31, "spi-hv", SPI_HV, true, true), \
+ _entry_(32, "uart", UART, true, false), \
+ _entry_(33, "usb-bias", USB_BIAS, true, false), \
+ _entry_(34, "usb0", USB0, true, false), \
+ _entry_(35, "usb1", USB1, true, false), \
+ _entry_(36, "usb2", USB2, true, false), \
+ _entry_(37, "usb3", USB3, true, false)
+
+#define TEGRA_IO_PAD_INFO(_id, _name, _pad_id, _vchange, _lpstate) \
+ { \
+ .name = _name, \
+ .pins = {(_id)}, \
+ .pad_id = TEGRA_IO_PAD_##_pad_id, \
+ .voltage_can_change = (_vchange), \
+ .support_low_power_state = (_lpstate), \
+ }
+
+static struct tegra_io_pads_cfg_info tegra210_io_pads_cfg_info[] = {
+ TEGRA210_PAD_INFO_TABLE(TEGRA_IO_PAD_INFO),
+};
+
+#define TEGRA_IO_PAD_DESC(_id, _name, _pad_id, _vchange, _lpstate) \
+ PINCTRL_PIN(_id, _name)
+
+static const struct pinctrl_pin_desc tegra210_io_pads_pinctrl_desc[] = {
+ TEGRA210_PAD_INFO_TABLE(TEGRA_IO_PAD_DESC),
+};
+
+struct tegra_io_pads_info {
+ struct device *dev;
+ struct pinctrl_dev *pctl;
+ struct tegra_io_pads_cfg_info *pads_cfg;
+ unsigned int num_pads_cfg;
+};
+
+static int tegra_iop_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
+{
+ struct tegra_io_pads_info *tiopi = pinctrl_dev_get_drvdata(pctldev);
+
+ return tiopi->num_pads_cfg;
+}
+
+static const char *tegra_iop_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
+ unsigned int group)
+{
+ struct tegra_io_pads_info *tiopi = pinctrl_dev_get_drvdata(pctldev);
+
+ return tiopi->pads_cfg[group].name;
+}
+
+static int tegra_iop_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
+ unsigned int group,
+ const unsigned int **pins,
+ unsigned int *num_pins)
+{
+ struct tegra_io_pads_info *tiopi = pinctrl_dev_get_drvdata(pctldev);
+
+ *pins = tiopi->pads_cfg[group].pins;
+ *num_pins = 1;
+
+ return 0;
+}
+
+static const struct pinctrl_ops tegra_iop_pinctrl_ops = {
+ .get_groups_count = tegra_iop_pinctrl_get_groups_count,
+ .get_group_name = tegra_iop_pinctrl_get_group_name,
+ .get_group_pins = tegra_iop_pinctrl_get_group_pins,
+ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
+ .dt_free_map = pinctrl_utils_free_map,
+};
+
+static int tegra_io_pad_pinconf_get(struct pinctrl_dev *pctldev,
+ unsigned int pin, unsigned long *config)
+{
+ struct tegra_io_pads_info *tiopi = pinctrl_dev_get_drvdata(pctldev);
+ int param = pinconf_to_config_param(*config);
+ struct tegra_io_pads_cfg_info *pad_cfg = &tiopi->pads_cfg[pin];
+ int pad_id = pad_cfg->pad_id;
+ int arg = 0;
+ int ret;
+
+ switch (param) {
+ case TEGRA_IO_PAD_POWER_SOURCE_VOLTAGE:
+ ret = tegra_io_pads_get_configured_voltage(pad_id);
+ if (ret < 0)
+ return ret;
+ arg = (ret = 3300000) ? 1 : 0;
+ break;
+
+ case PIN_CONFIG_LOW_POWER_MODE:
+ ret = tegra_io_pads_power_is_enabled(pad_id);
+ if (ret < 0)
+ return ret;
+ arg = !ret;
+ break;
+
+ default:
+ dev_err(tiopi->dev, "The parameter %d not supported\n", param);
+ return -EINVAL;
+ }
+
+ *config = pinconf_to_config_packed(param, (u16)arg);
+ return 0;
+}
+
+static int tegra_io_pad_pinconf_set(struct pinctrl_dev *pctldev,
+ unsigned int pin, unsigned long *configs,
+ unsigned int num_configs)
+{
+ struct tegra_io_pads_info *tiopi = pinctrl_dev_get_drvdata(pctldev);
+ struct tegra_io_pads_cfg_info *pad_cfg = &tiopi->pads_cfg[pin];
+ u16 param_val;
+ int pad_id = pad_cfg->pad_id;
+ int volt;
+ int param;
+ int ret;
+ int i;
+
+ for (i = 0; i < num_configs; i++) {
+ param = pinconf_to_config_param(configs[i]);
+ param_val = pinconf_to_config_argument(configs[i]);
+
+ switch (param) {
+ case TEGRA_IO_PAD_POWER_SOURCE_VOLTAGE:
+ volt = (param_val) ? 3300000 : 1800000;
+ ret = tegra_io_pads_configure_voltage(pad_id, volt);
+ if (ret < 0) {
+ dev_err(tiopi->dev,
+ "Failed to configure pad %s for voltage %d: %d\n",
+ pad_cfg->name, param_val, ret);
+ return ret;
+ }
+ break;
+
+ case PIN_CONFIG_LOW_POWER_MODE:
+ if (param_val)
+ ret = tegra_io_pads_power_disable(pad_id);
+ else
+ ret = tegra_io_pads_power_enable(pad_id);
+ if (ret < 0) {
+ dev_err(tiopi->dev,
+ "Failed to set low power %s of pad %s: %d\n",
+ param_val ? "enable" : "disable",
+ pad_cfg->name, ret);
+ return ret;
+ }
+ break;
+
+ default:
+ dev_err(tiopi->dev, "The parameter %d not supported\n",
+ param);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+static const struct pinconf_ops tegra_io_pad_pinconf_ops = {
+ .pin_config_get = tegra_io_pad_pinconf_get,
+ .pin_config_set = tegra_io_pad_pinconf_set,
+};
+
+static struct pinctrl_desc tegra_iop_pinctrl_desc = {
+ .name = "pinctrl-tegra-io-pads",
+ .pctlops = &tegra_iop_pinctrl_ops,
+ .confops = &tegra_io_pad_pinconf_ops,
+ .pins = tegra210_io_pads_pinctrl_desc,
+ .npins = ARRAY_SIZE(tegra210_io_pads_pinctrl_desc),
+ .custom_params = tegra_io_pads_cfg_params,
+ .num_custom_params = ARRAY_SIZE(tegra_io_pads_cfg_params),
+};
+
+static int tegra_iop_pinctrl_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np_parent = pdev->dev.parent->of_node;
+ struct tegra_io_pads_info *tiopi;
+
+ if (!np_parent) {
+ dev_err(&pdev->dev, "PMC should be register from DT\n");
+ return -ENODEV;
+ }
+
+ pdev->dev.of_node = np_parent;
+
+ tiopi = devm_kzalloc(&pdev->dev, sizeof(*tiopi), GFP_KERNEL);
+ if (!tiopi)
+ return -ENOMEM;
+
+ tiopi->dev = &pdev->dev;
+ tiopi->dev->of_node = pdev->dev.of_node;
+ tiopi->pads_cfg = tegra210_io_pads_cfg_info;
+ tiopi->num_pads_cfg = ARRAY_SIZE(tegra210_io_pads_cfg_info);
+
+ platform_set_drvdata(pdev, tiopi);
+
+ tiopi->pctl = pinctrl_register(&tegra_iop_pinctrl_desc, dev, tiopi);
+ if (IS_ERR(tiopi->pctl)) {
+ dev_err(&pdev->dev, "Couldn't register pinctrl driver\n");
+ return PTR_ERR(tiopi->pctl);
+ }
+
+ return 0;
+}
+
+static int tegra_iop_pinctrl_remove(struct platform_device *pdev)
+{
+ struct tegra_io_pads_info *tiopi = platform_get_drvdata(pdev);
+
+ pinctrl_unregister(tiopi->pctl);
+
+ return 0;
+}
+
+static struct platform_driver tegra_iop_pinctrl_driver = {
+ .driver = {
+ .name = "pinctrl-tegra210-io-pad",
+ },
+ .probe = tegra_iop_pinctrl_probe,
+ .remove = tegra_iop_pinctrl_remove,
+};
+
+builtin_platform_driver(tegra_iop_pinctrl_driver);
--
2.1.4
next prev parent reply other threads:[~2016-05-02 12:31 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-05-02 12:17 [PATCH 0/6] soc/tegra: Add support for IO pads control via pinctrl interface Laxman Dewangan
2016-05-02 12:17 ` [PATCH 1/6] soc/tegra: pmc: Use BIT macro for register field definition Laxman Dewangan
2016-05-02 12:17 ` [PATCH 2/6] soc/tegra: pmc: Correct type of variable for tegra_pmc_readl() Laxman Dewangan
2016-05-03 11:42 ` Jon Hunter
2016-05-02 12:17 ` [PATCH 3/6] soc/tegra: pmc: Add support for IO pads power state and voltage Laxman Dewangan
2016-05-03 12:34 ` Jon Hunter
2016-05-03 12:31 ` Laxman Dewangan
2016-05-03 12:55 ` Jon Hunter
2016-05-03 12:48 ` Laxman Dewangan
2016-05-03 13:12 ` Jon Hunter
2016-05-03 13:07 ` Laxman Dewangan
2016-05-02 12:17 ` [PATCH 4/6] soc/tegra: pmc: Register PMC child devices as platform device Laxman Dewangan
2016-05-03 12:36 ` Jon Hunter
2016-05-03 15:26 ` Jon Hunter
2016-05-02 12:17 ` [PATCH 5/6] pinctrl: tegra: Add DT binding for io pads control Laxman Dewangan
2016-05-03 12:44 ` Jon Hunter
2016-05-03 12:54 ` Laxman Dewangan
2016-05-03 13:33 ` Jon Hunter
2016-05-02 12:17 ` Laxman Dewangan [this message]
2016-05-11 9:19 ` [PATCH 6/6] pinctrl: tegra: Add driver to configure voltage and power state of io pads Linus Walleij
2016-05-11 16:07 ` Stephen Warren
2016-05-12 10:30 ` Jon Hunter
2016-05-12 19:02 ` Javier Martinez Canillas
2016-05-12 19:48 ` Jon Hunter
2016-05-03 11:38 ` [PATCH 0/6] soc/tegra: Add support for IO pads control via pinctrl interface Jon Hunter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1462191434-28933-7-git-send-email-ldewangan@nvidia.com \
--to=ldewangan@nvidia.com \
--cc=devicetree@vger.kernel.org \
--cc=gnurou@gmail.com \
--cc=jonathanh@nvidia.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=swarren@wwwdotorg.org \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®