[PATCH 11/36] usb: serial: ti_usb_3410_5052: Use C_X macros instead of c_cflag manipulation

[Mathieu OTHACEHE <m.othacehe@gmail.com>]

Use C_X tty.h macros to avoid direct manipulation of termios
c_cflag variable.

Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
---
 drivers/usb/serial/ti_usb_3410_5052.c | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c
index ef6789b..601fab6 100644
--- a/drivers/usb/serial/ti_usb_3410_5052.c
+++ b/drivers/usb/serial/ti_usb_3410_5052.c
@@ -936,7 +936,7 @@ static void ti_set_termios(struct tty_struct *tty,
 	config->wFlags |= TI_UART_ENABLE_AUTO_START_DMA;
 	config->bUartMode = tport->tp_uart_mode;
 
-	switch (cflag & CSIZE) {
+	switch (C_CSIZE(tty)) {
 	case CS5:
 		    config->bDataBits = TI_UART_5_DATA_BITS;
 		    break;
@@ -955,8 +955,8 @@ static void ti_set_termios(struct tty_struct *tty,
 	/* CMSPAR isn't supported by this driver */
 	tty->termios.c_cflag &= ~CMSPAR;
 
-	if (cflag & PARENB) {
-		if (cflag & PARODD) {
+	if (C_PARENB(tty)) {
+		if (C_PARODD(tty)) {
 			config->wFlags |= TI_UART_ENABLE_PARITY_CHECKING;
 			config->bParity = TI_UART_ODD_PARITY;
 		} else {
@@ -968,14 +968,14 @@ static void ti_set_termios(struct tty_struct *tty,
 		config->bParity = TI_UART_NO_PARITY;
 	}
 
-	if (cflag & CSTOPB)
+	if (C_CSTOPB(tty))
 		config->bStopBits = TI_UART_2_STOP_BITS;
 	else
 		config->bStopBits = TI_UART_1_STOP_BITS;
 
-	if (cflag & CRTSCTS) {
+	if (C_CRTSCTS(tty)) {
 		/* RTS flow control must be off to drop RTS for baud rate B0 */
-		if ((cflag & CBAUD) != B0)
+		if ((C_BAUD(tty)) != B0)
 			config->wFlags |= TI_UART_ENABLE_RTS_IN;
 		config->wFlags |= TI_UART_ENABLE_CTS_OUT;
 	} else {
@@ -1004,7 +1004,7 @@ static void ti_set_termios(struct tty_struct *tty,
 		config->wBaudRate = (__u16)((461538 + baud/2) / baud);
 
 	/* FIXME: Should calculate resulting baud here and report it back */
-	if ((cflag & CBAUD) != B0)
+	if ((C_BAUD(tty)) != B0)
 		tty_encode_baud_rate(tty, baud, baud);
 
 	dev_dbg(&port->dev,
@@ -1026,7 +1026,7 @@ static void ti_set_termios(struct tty_struct *tty,
 	/* SET_CONFIG asserts RTS and DTR, reset them correctly */
 	mcr = tport->tp_shadow_mcr;
 	/* if baud rate is B0, clear RTS and DTR */
-	if ((cflag & CBAUD) == B0)
+	if (C_BAUD(tty) == B0)
 		mcr &= ~(TI_MCR_DTR | TI_MCR_RTS);
 	status = ti_set_mcr(tport, mcr);
 	if (status)
-- 
2.8.2