mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Ludovic Desroches <ludovic.desroches@atmel.com>
To: <adrian.hunter@intel.com>, <ulf.hansson@linaro.org>
Cc: <linux-mmc@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<nicolas.ferre@atmel.com>, <kliu5@marvell.com>,
	<jlfu@marvell.com>, <jszhang@marvell.com>,
	Ludovic Desroches <ludovic.desroches@atmel.com>
Subject: [RESEND PATCH] mmc: sdhci: fix wakeup configuration
Date: Fri, 13 May 2016 15:14:46 +0200	[thread overview]
Message-ID: <1463145286-7684-1-git-send-email-ludovic.desroches@atmel.com> (raw)

Activating wakeup event is not enough to get a wakeup signal. The
corresponding events have to be enabled in the Interrupt Status Enable
Register too.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
---
Hi,

I just updated sdhci_enable_irq_wakeups() not sdhci_disable_irq_wakeups()
because I don't think it is necessary to configure SDHCI_INT_ENABLE at this
step, it will be done with sdhci_init() or sdhci_enable_card_detection().

While I was writing this patch, several questions came to my mind:
- Is the naming correct? wakeup signal is not an irq. 'enable_irq_wakeups' can
  be a bit confusing.
- If we want to wakeup from irq, we may have to set SDHCI_INT_ENABLE and
  SDHCI_SIGNAL_ENABLE and not rely on a previous configuration, isn't it?

Regards

Ludovic

 drivers/mmc/host/sdhci.c | 26 ++++++++++++++++++--------
 1 file changed, 18 insertions(+), 8 deletions(-)

diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index b284924..6fc69ed 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -2638,18 +2638,28 @@ static irqreturn_t sdhci_thread_irq(int irq, void *dev_id)
 \*****************************************************************************/
 
 #ifdef CONFIG_PM
+/*
+ * To enable wakeup events, the corresponding events have to be enabled in
+ * the Interrupt Status Enable register too. See 'Table 1-6: Wakeup Signal
+ * Table' in the SD Host Controller Standard Specification.
+ */
 void sdhci_enable_irq_wakeups(struct sdhci_host *host)
 {
-	u8 val;
-	u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE
-			| SDHCI_WAKE_ON_INT;
+	u8 wakeup_val;
+	u8 wakeup_mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE |
+			 SDHCI_WAKE_ON_INT;
+	u32 irq_val = SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE |
+		      SDHCI_INT_CARD_INT;
 
-	val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
-	val |= mask ;
+	wakeup_val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
+	wakeup_val |= wakeup_mask;
 	/* Avoid fake wake up */
-	if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
-		val &= ~(SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE);
-	sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
+	if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) {
+		wakeup_val &= ~(SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE);
+		irq_val &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE);
+	}
+	sdhci_writeb(host, wakeup_val, SDHCI_WAKE_UP_CONTROL);
+	sdhci_writel(host, irq_val, SDHCI_INT_ENABLE);
 }
 EXPORT_SYMBOL_GPL(sdhci_enable_irq_wakeups);
 
-- 
2.5.0

             reply	other threads:[~2016-05-13 13:14 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-05-13 13:14 Ludovic Desroches [this message]
2016-05-13 13:17 ` Ludovic Desroches
  -- strict thread matches above, loose matches on Subject: below --
2016-05-13  9:27 Ludovic Desroches
2016-05-13 11:37 ` Adrian Hunter
2016-05-13 12:19   ` Ludovic Desroches
2016-05-13 12:46     ` Adrian Hunter

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1463145286-7684-1-git-send-email-ludovic.desroches@atmel.com \
    --to=ludovic.desroches@atmel.com \
    --cc=adrian.hunter@intel.com \
    --cc=jlfu@marvell.com \
    --cc=jszhang@marvell.com \
    --cc=kliu5@marvell.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=nicolas.ferre@atmel.com \
    --cc=ulf.hansson@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®