From: John Stultz <john.stultz@linaro.org>
To: lkml <linux-kernel@vger.kernel.org>
Cc: John Stultz <john.stultz@linaro.org>,
David Airlie <airlied@linux.ie>,
Archit Taneja <architt@codeaurora.org>,
Wolfram Sang <wsa+renesas@sang-engineering.com>,
Lars-Peter Clausen <lars@metafoo.de>,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
dri-devel@lists.freedesktop.org
Subject: [RFC][PATCH 5/5 v2] drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID
Date: Mon, 28 Nov 2016 21:04:44 -0800 [thread overview]
Message-ID: <1480395884-5471-6-git-send-email-john.stultz@linaro.org> (raw)
In-Reply-To: <1480395884-5471-1-git-send-email-john.stultz@linaro.org>
I've found that by just turning the chip on and off via the
POWER_DOWN register, I end up getting i2c_transfer errors
on HiKey.
Investigating further, it seems some of the register state
in the regmap cache is somehow getting lost. Using the logic
in __adv7511_power_on/off() which syncs and dirtys the cache
avoids this issue.
Thus this patch changes the EDID probing logic so that we
re-use the __adv7511_power_on/off() calls.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
---
v2: Split into two patches to make the change more clear.
Also provided more rational as to why the change is
important.
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 17 +++--------------
1 file changed, 3 insertions(+), 14 deletions(-)
diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
index 1948968..487b33d 100644
--- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
+++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
@@ -559,24 +559,13 @@ static int adv7511_get_modes(struct adv7511 *adv7511,
unsigned int count;
/* Reading the EDID only works if the device is powered */
- if (!adv7511->powered) {
- regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
- ADV7511_POWER_POWER_DOWN, 0);
- if (adv7511->i2c_main->irq) {
- regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0),
- ADV7511_INT0_EDID_READY);
- regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(1),
- ADV7511_INT1_DDC_ERROR);
- }
- adv7511->current_edid_segment = -1;
- }
+ if (!adv7511->powered)
+ __adv7511_power_on(adv7511);
edid = drm_do_get_edid(connector, adv7511_get_edid_block, adv7511);
if (!adv7511->powered)
- regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
- ADV7511_POWER_POWER_DOWN,
- ADV7511_POWER_POWER_DOWN);
+ __adv7511_power_off(adv7511);
kfree(adv7511->edid);
adv7511->edid = edid;
--
2.7.4
next prev parent reply other threads:[~2016-11-29 5:05 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-29 5:04 [RFC][PATCH 0/5 v2] adv7511 EDID probing improvements John Stultz
2016-11-29 5:04 ` [RFC][PATCH 1/5 v2] drm/bridge: adv7511: Use work_struct to defer hotplug handing to out of irq context John Stultz
2016-11-29 6:46 ` Laurent Pinchart
2016-11-29 17:04 ` John Stultz
2016-11-29 5:04 ` [RFC][PATCH 2/5 v2] drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event() John Stultz
2016-11-29 6:50 ` Laurent Pinchart
2016-11-29 17:58 ` John Stultz
2016-11-29 5:04 ` [RFC][PATCH 3/5 v2] drm/bridge: adv7511: Enable HPD interrupts to support hotplug and improve monitor detection John Stultz
2016-11-29 5:04 ` [RFC][PATCH 4/5 v2] drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally John Stultz
2016-11-29 5:04 ` John Stultz [this message]
2016-11-30 4:42 ` [RFC][PATCH 5/5 v2] drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID Archit Taneja
2016-12-12 8:40 ` [RFC][PATCH 0/5 v2] adv7511 EDID probing improvements Archit Taneja
2016-12-12 19:06 ` John Stultz
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1480395884-5471-6-git-send-email-john.stultz@linaro.org \
--to=john.stultz@linaro.org \
--cc=airlied@linux.ie \
--cc=architt@codeaurora.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=lars@metafoo.de \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-kernel@vger.kernel.org \
--cc=wsa+renesas@sang-engineering.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome