From: Oza Pawandeep <oza.oza@broadcom.com>
To: Bjorn Helgaas <bhelgaas@google.com>, Ray Jui <rjui@broadcom.com>,
Scott Branden <sbranden@broadcom.com>,
Jon Mason <jonmason@broadcom.com>,
bcm-kernel-feedback-list@broadcom.com,
Oza Pawandeep <oza.oza@broadcom.com>,
Andy Gospodarek <gospo@broadcom.com>,
linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org,
Oza Pawandeep <oza.pawandeep@gmail.com>
Subject: [PATCH v4 1/2] PCI: iproc: Retry request when CRS returned from EP
Date: Wed, 5 Jul 2017 08:38:58 +0530 [thread overview]
Message-ID: <1499224139-10746-2-git-send-email-oza.oza@broadcom.com> (raw)
In-Reply-To: <1499224139-10746-1-git-send-email-oza.oza@broadcom.com>
For Configuration Requests only, following reset it is possible for a
device to terminate the request but indicate that it is temporarily unable
to process the Request, but will be able to process the Request in the
future – in this case, the Configuration Request Retry Status 100 (CRS)
Completion Status is used.
As per PCI spec, CRS Software Visibility only affects config read of the
Vendor ID, for config write or any other config read the Root must
automatically re-issue configuration request again as a new request.
Iproc based PCIe RC (hw) does not retry request on its own.
As a result of the fact, PCIe RC driver (sw) should take care of CRS.
This patch fixes the problem, and attempts to read config space again in
case of PCIe code forwarding the CRS back to CPU.
It implements iproc_pcie_config_read which gets called for Stingray,
Otherwise it falls back to PCI generic APIs.
Signed-off-by: Oza Pawandeep <oza.oza@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
diff --git a/drivers/pci/host/pcie-iproc.c b/drivers/pci/host/pcie-iproc.c
index 0f39bd2..b0abcd7 100644
--- a/drivers/pci/host/pcie-iproc.c
+++ b/drivers/pci/host/pcie-iproc.c
@@ -68,6 +68,9 @@
#define APB_ERR_EN_SHIFT 0
#define APB_ERR_EN BIT(APB_ERR_EN_SHIFT)
+#define CFG_RETRY_STATUS 0xffff0001
+#define CFG_RETRY_STATUS_TIMEOUT_US 500000 /* 500 milli-seconds. */
+
/* derive the enum index of the outbound/inbound mapping registers */
#define MAP_REG(base_reg, index) ((base_reg) + (index) * 2)
@@ -448,6 +451,55 @@ static inline void iproc_pcie_apb_err_disable(struct pci_bus *bus,
}
}
+static int iproc_pcie_cfg_retry(void __iomem *cfg_data_p)
+{
+ int timeout = CFG_RETRY_STATUS_TIMEOUT_US;
+ unsigned int ret;
+
+ /*
+ * As per PCI spec, CRS Software Visibility only
+ * affects config read of the Vendor ID.
+ * For config write or any other config read the Root must
+ * automatically re-issue configuration request again as a
+ * new request. Iproc based PCIe RC (hw) does not retry
+ * request on its own, so handle it here.
+ */
+ do {
+ ret = readl(cfg_data_p);
+ if (ret == CFG_RETRY_STATUS)
+ udelay(1);
+ else
+ return PCIBIOS_SUCCESSFUL;
+ } while (timeout--);
+
+ return PCIBIOS_DEVICE_NOT_FOUND;
+}
+
+static void __iomem *iproc_pcie_map_ep_cfg_reg(struct iproc_pcie *pcie,
+ unsigned int busno,
+ unsigned int slot,
+ unsigned int fn,
+ int where)
+{
+ u16 offset;
+ u32 val;
+
+ /* EP device access */
+ val = (busno << CFG_ADDR_BUS_NUM_SHIFT) |
+ (slot << CFG_ADDR_DEV_NUM_SHIFT) |
+ (fn << CFG_ADDR_FUNC_NUM_SHIFT) |
+ (where & CFG_ADDR_REG_NUM_MASK) |
+ (1 & CFG_ADDR_CFG_TYPE_MASK);
+
+ iproc_pcie_write_reg(pcie, IPROC_PCIE_CFG_ADDR, val);
+ offset = iproc_pcie_reg_offset(pcie, IPROC_PCIE_CFG_DATA);
+
+ if (iproc_pcie_reg_is_invalid(offset))
+ return NULL;
+
+ return (pcie->base + offset);
+}
+
/**
* Note access to the configuration registers are protected at the higher layer
* by 'pci_lock' in drivers/pci/access.c
@@ -499,13 +551,48 @@ static void __iomem *iproc_pcie_map_cfg_bus(struct pci_bus *bus,
return (pcie->base + offset);
}
+static int iproc_pcie_config_read(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 *val)
+{
+ struct iproc_pcie *pcie = iproc_data(bus);
+ unsigned int slot = PCI_SLOT(devfn);
+ unsigned int fn = PCI_FUNC(devfn);
+ unsigned int busno = bus->number;
+ void __iomem *cfg_data_p;
+ int ret;
+
+ /* root complex access. */
+ if (busno == 0)
+ return pci_generic_config_read32(bus, devfn, where, size, val);
+
+ cfg_data_p = iproc_pcie_map_ep_cfg_reg(pcie, busno, slot, fn, where);
+
+ if (!cfg_data_p)
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ ret = iproc_pcie_cfg_retry(cfg_data_p);
+ if (ret)
+ return ret;
+
+ *val = readl(cfg_data_p);
+
+ if (size <= 2)
+ *val = (*val >> (8 * (where & 3))) & ((1 << (size * 8)) - 1);
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
static int iproc_pcie_config_read32(struct pci_bus *bus, unsigned int devfn,
int where, int size, u32 *val)
{
int ret;
+ struct iproc_pcie *pcie = iproc_data(bus);
iproc_pcie_apb_err_disable(bus, true);
- ret = pci_generic_config_read32(bus, devfn, where, size, val);
+ if (pcie->type == IPROC_PCIE_PAXB_V2)
+ ret = iproc_pcie_config_read(bus, devfn, where, size, val);
+ else
+ ret = pci_generic_config_read32(bus, devfn, where, size, val);
iproc_pcie_apb_err_disable(bus, false);
return ret;
--
1.9.1
next prev parent reply other threads:[~2017-07-05 3:09 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-07-05 3:08 [PATCH v4 0/2] PCI: iproc: SOC specific fixes Oza Pawandeep
2017-07-05 3:08 ` Oza Pawandeep [this message]
2017-07-05 3:08 ` [PATCH v4 2/2] PCI: iproc: add device shutdown for PCI RC Oza Pawandeep
2017-07-05 3:51 ` Ray Jui
2017-07-05 8:37 ` Oza Oza
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1499224139-10746-2-git-send-email-oza.oza@broadcom.com \
--to=oza.oza@broadcom.com \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=bhelgaas@google.com \
--cc=gospo@broadcom.com \
--cc=jonmason@broadcom.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=oza.pawandeep@gmail.com \
--cc=rjui@broadcom.com \
--cc=sbranden@broadcom.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®