mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Tim Harvey <tharvey@gateworks.com>
To: linux-media@vger.kernel.org
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	shawnguo@kernel.org, Steve Longerbeam <slongerbeam@gmail.com>,
	Philipp Zabel <p.zabel@pengutronix.de>,
	Hans Verkuil <hansverk@cisco.com>,
	Mauro Carvalho Chehab <mchehab@s-opensource.com>
Subject: [PATCH 4/4] ARM: DTS: imx: ventana: add TDA19971 HDMI Receiver to GW54xx
Date: Fri, 22 Sep 2017 15:24:13 -0700	[thread overview]
Message-ID: <1506119053-21828-5-git-send-email-tharvey@gateworks.com> (raw)
In-Reply-To: <1506119053-21828-1-git-send-email-tharvey@gateworks.com>

The GW54xx has a front-panel microHDMI connector routed to a TDA19971
which is connected the the IPU CSI when using IMX6Q.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
 arch/arm/boot/dts/imx6q-gw54xx.dts | 85 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 85 insertions(+)

diff --git a/arch/arm/boot/dts/imx6q-gw54xx.dts b/arch/arm/boot/dts/imx6q-gw54xx.dts
index 56e5b50..efb7dd3 100644
--- a/arch/arm/boot/dts/imx6q-gw54xx.dts
+++ b/arch/arm/boot/dts/imx6q-gw54xx.dts
@@ -12,6 +12,7 @@
 /dts-v1/;
 #include "imx6q.dtsi"
 #include "imx6qdl-gw54xx.dtsi"
+#include <dt-bindings/media/tda1997x.h>
 
 / {
 	model = "Gateworks Ventana i.MX6 Dual/Quad GW54XX";
@@ -35,6 +36,60 @@
 			};
 		};
 	};
+
+	tda1997x: tda1997x@48 {
+		compatible = "nxp,tda19971";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tda1997x>;
+		reg = <0x48>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		DOVDD-supply = <&reg_3p3v>;
+		AVDD-supply = <&sw4_reg>;
+		DVDD-supply = <&sw4_reg>;
+		audio-port = < TDA1997X_I2S16
+		               TDA1997X_LAYOUT0
+			       TDA1997X_ACLK_128FS >;
+		/*
+		 * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
+		 * and Y[11:4] across 16bits in the same cycle
+		 * which we map to VP[15:08]<->CSI_DATA[19:12]
+		 */
+		vidout_portcfg =
+			/*G_Y_11_8<->VP[15:12]<->CSI_DATA[19:16]*/
+			< TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
+			/*G_Y_7_4<->VP[11:08]<->CSI_DATA[15:12]*/
+			< TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
+			/*R_CR_CBCR_11_8<->VP[07:04]<->CSI_DATA[11:08]*/
+			< TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
+			/*R_CR_CBCR_7_4<->VP[03:00]<->CSI_DATA[07:04]*/
+			< TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
+		max-pixel-rate = <180>; /* IMX6 CSI max pixel rate 180MP/sec */
+
+		port {
+			tda1997x_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <16>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				data-active = <1>;
+			};
+		};
+	};
+};
+
+&ipu1_csi0_from_ipu1_csi0_mux {
+	bus-width = <16>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&tda1997x_to_ipu1_csi0_mux>;
+	bus-width = <16>;
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
 };
 
 &ipu2_csi1_from_ipu2_csi1_mux {
@@ -63,6 +118,30 @@
 		>;
 	};
 
+	pinctrl_ipu1_csi0: ipu1_csi0grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19		0x1b0b0
+			MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC		0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK	0x1b0b0
+			MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC		0x1b0b0
+		>;
+	};
+
 	pinctrl_ipu2_csi1: ipu2_csi1grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_EB2__IPU2_CSI1_DATA19    0x1b0b0
@@ -78,4 +157,10 @@
 			MX6QDL_PAD_EIM_A16__IPU2_CSI1_PIXCLK    0x1b0b0
 		>;
 	};
+
+	pinctrl_tda1997x: tda1997xgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07	0x1b0b0
+		>;
+	};
 };
-- 
2.7.4

      parent reply	other threads:[~2017-09-22 22:21 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-09-22 22:24 [PATCH 0/4] RFC: TDA1997x HDMI video receiver Tim Harvey
2017-09-22 22:24 ` [PATCH 1/4] MAINTAINERS: add entry for NXP TDA1997x driver Tim Harvey
2017-09-22 22:24 ` [PATCH 2/4] media: dt-bindings: Add bindings for TDA1997X Tim Harvey
2017-10-04 21:14   ` Rob Herring
2017-10-05 17:06     ` Tim Harvey
2017-09-22 22:24 ` [PATCH 3/4] media: i2c: Add TDA1997x HDMI receiver driver Tim Harvey
2017-09-23  7:30   ` Hans Verkuil
2017-09-25 20:44     ` Tim Harvey
2017-09-22 22:24 ` Tim Harvey [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1506119053-21828-5-git-send-email-tharvey@gateworks.com \
    --to=tharvey@gateworks.com \
    --cc=devicetree@vger.kernel.org \
    --cc=hansverk@cisco.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=mchehab@s-opensource.com \
    --cc=p.zabel@pengutronix.de \
    --cc=shawnguo@kernel.org \
    --cc=slongerbeam@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®