On Fri, 2017-10-13 at 12:16 +0800, Joel Stanley wrote:
> According to the ASPEED datasheet, gigabit speeds require a clock of
> 100MHz or higher. Other speeds require 25MHz or higher. This patch
> configures a 100MHz clock if the system has a direct-attached
> PHY, or 25MHz if the system is running NC-SI which is limited to 100MHz.
> 
> There appear to be no other upstream users of the FTGMAC100 driver it is
> hard to know the clocking requirements of other platforms. Therefore a
> conservative approach was taken with enabling clocks. If the platform is
> not ASPEED, both requesting the clock and configuring the speed is
> skipped.
> 
> Signed-off-by: Joel Stanley <joel@jms.id.au>

Tested on an AST2500 EVB and an OpenPOWER Palmetto (AST2400) machine.
Confirmed clock rates were nominally what was requested, and successfully
downloaded a 100MB test file.

Tested-by: Andrew Jeffery <andrew@aj.id.au>

> ---
> Andrew, can you please give this one a spin on hardware?
> 
> v3:
>  - Fix errors from v2
> v2:
>  - only touch the clocks on Aspeed platforms
>  - unconditionally call clk_unprepare_disable
> 
>  drivers/net/ethernet/faraday/ftgmac100.c | 26 ++++++++++++++++++++++++++
>  1 file changed, 26 insertions(+)
> 
> diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
> index 9ed8e4b81530..78db8e62a83f 100644
> --- a/drivers/net/ethernet/faraday/ftgmac100.c
> +++ b/drivers/net/ethernet/faraday/ftgmac100.c
> @@ -21,6 +21,7 @@
>  
>  #define pr_fmt(fmt)	KBUILD_MODNAME ": " fmt
>  
> +#include <linux/clk.h>
>  #include <linux/dma-mapping.h>
>  #include <linux/etherdevice.h>
>  #include <linux/ethtool.h>
> @@ -59,6 +60,9 @@
>  /* Min number of tx ring entries before stopping queue */
>  #define TX_THRESHOLD		(MAX_SKB_FRAGS + 1)
>  
> +#define FTGMAC_100MHZ		100000000
> +#define FTGMAC_25MHZ		25000000
> +
>  struct ftgmac100 {
>  	/* Registers */
>  	struct resource *res;
> @@ -96,6 +100,7 @@ struct ftgmac100 {
>  	struct napi_struct napi;
>  	struct work_struct reset_task;
>  	struct mii_bus *mii_bus;
> +	struct clk *clk;
>  
>  	/* Link management */
>  	int cur_speed;
> @@ -1734,6 +1739,22 @@ static void ftgmac100_ncsi_handler(struct ncsi_dev *nd)
>  		    nd->link_up ? "up" : "down");
>  }
>  
> +static void ftgmac100_setup_clk(struct ftgmac100 *priv)
> +{
> +	priv->clk = devm_clk_get(priv->dev, NULL);
> +	if (IS_ERR(priv->clk))
> +		return;
> +
> +	clk_prepare_enable(priv->clk);
> +
> +	/* Aspeed specifies a 100MHz clock is required for up to
> +	 * 1000Mbit link speeds. As NCSI is limited to 100Mbit, 25MHz
> +	 * is sufficient
> +	 */
> +	clk_set_rate(priv->clk, priv->use_ncsi ? FTGMAC_25MHZ :
> +			FTGMAC_100MHZ);
> +}
> +
>  static int ftgmac100_probe(struct platform_device *pdev)
>  {
>  	struct resource *res;
> @@ -1830,6 +1851,9 @@ static int ftgmac100_probe(struct platform_device *pdev)
>  			goto err_setup_mdio;
>  	}
>  
> +	if (priv->is_aspeed)
> +		ftgmac100_setup_clk(priv);
> +
>  	/* Default ring sizes */
>  	priv->rx_q_entries = priv->new_rx_q_entries = DEF_RX_QUEUE_ENTRIES;
>  	priv->tx_q_entries = priv->new_tx_q_entries = DEF_TX_QUEUE_ENTRIES;
> @@ -1883,6 +1907,8 @@ static int ftgmac100_remove(struct platform_device *pdev)
>  
>  	unregister_netdev(netdev);
>  
> +	clk_disable_unprepare(priv->clk);
> +
>  	/* There's a small chance the reset task will have been re-queued,
>  	 * during stop, make sure it's gone before we free the structure.
>  	 */