From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1752204AbeBCIAX (ORCPT ); Sat, 3 Feb 2018 03:00:23 -0500 Received: from smtp.codeaurora.org ([198.145.29.96]:35738 "EHLO smtp.codeaurora.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751990AbeBCH64 (ORCPT ); Sat, 3 Feb 2018 02:58:56 -0500 DMARC-Filter: OpenDMARC Filter v1.3.2 smtp.codeaurora.org 7A6DF6081C Authentication-Results: pdx-caf-mail.web.codeaurora.org; dmarc=none (p=none dis=none) header.from=codeaurora.org Authentication-Results: pdx-caf-mail.web.codeaurora.org; spf=none smtp.mailfrom=absahu@codeaurora.org From: Abhishek Sahu To: Andy Gross , Wolfram Sang Cc: David Brown , Sricharan R , linux-arm-msm@vger.kernel.org, linux-soc@vger.kernel.org, linux-i2c@vger.kernel.org, linux-kernel@vger.kernel.org, Abhishek Sahu Subject: [PATCH 08/12] i2c: qup: change completion timeout according to transfer length Date: Sat, 3 Feb 2018 13:28:13 +0530 Message-Id: <1517644697-30806-9-git-send-email-absahu@codeaurora.org> X-Mailer: git-send-email 1.9.1 In-Reply-To: <1517644697-30806-1-git-send-email-absahu@codeaurora.org> References: <1517644697-30806-1-git-send-email-absahu@codeaurora.org> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Currently the completion timeout is being taken according to maximum transfer length which is too high if SCL is operating in high frequency. This patch calculates timeout on the basis of one-byte transfer time and uses the same for completion timeout. Signed-off-by: Abhishek Sahu --- drivers/i2c/busses/i2c-qup.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c index a91fc70..6df65ea 100644 --- a/drivers/i2c/busses/i2c-qup.c +++ b/drivers/i2c/busses/i2c-qup.c @@ -130,8 +130,8 @@ #define MX_TX_RX_LEN SZ_64K #define MX_BLOCKS (MX_TX_RX_LEN / QUP_READ_LIMIT) -/* Max timeout in ms for 32k bytes */ -#define TOUT_MAX 300 +/* Min timeout for i2c transfers */ +#define TOUT_MIN 2 /* Default values. Use these if FW query fails */ #define DEFAULT_CLK_FREQ 100000 @@ -172,6 +172,7 @@ struct qup_i2c_dev { int in_blk_sz; unsigned long one_byte_t; + unsigned long xfer_timeout; struct qup_i2c_block blk; struct i2c_msg *msg; @@ -845,7 +846,7 @@ static int qup_i2c_bam_do_xfer(struct qup_i2c_dev *qup, struct i2c_msg *msg, dma_async_issue_pending(qup->brx.dma); } - if (!wait_for_completion_timeout(&qup->xfer, TOUT_MAX * HZ)) { + if (!wait_for_completion_timeout(&qup->xfer, qup->xfer_timeout)) { dev_err(qup->dev, "normal trans timed out\n"); ret = -ETIMEDOUT; } @@ -1601,6 +1602,8 @@ static int qup_i2c_probe(struct platform_device *pdev) */ one_bit_t = (USEC_PER_SEC / clk_freq) + 1; qup->one_byte_t = one_bit_t * 9; + qup->xfer_timeout = TOUT_MIN * HZ + + usecs_to_jiffies(MX_TX_RX_LEN * qup->one_byte_t); dev_dbg(qup->dev, "IN:block:%d, fifo:%d, OUT:block:%d, fifo:%d\n", qup->in_blk_sz, qup->in_fifo_sz, -- QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation