From: Matheus Castello <matheus@castello.eng.br>
To: stefan.wahren@i2se.com
Cc: eric@anholt.net, linus.walleij@linaro.org,
linux-kernel@vger.kernel.org,
Matheus Castello <matheus@castello.eng.br>
Subject: [PATCH] pinctrl: bc2835: Add brcm,level property
Date: Thu, 22 Feb 2018 13:44:35 -0400 [thread overview]
Message-ID: <1519321475-973-1-git-send-email-matheus@castello.eng.br> (raw)
Property to set initial value of pin output buffer.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
---
.../bindings/pinctrl/brcm,bcm2835-gpio.txt | 5 +-
drivers/pinctrl/bcm/pinctrl-bcm2835.c | 90 +++++++++++++++++-----
2 files changed, 75 insertions(+), 20 deletions(-)
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt
index 2569866..6834f1d 100644
--- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt
@@ -54,8 +54,11 @@ Optional subnode-properties:
0: none
1: down
2: up
+- brcm,level: Integer, representing the value of output buffer to apply to the pin(s):
+ 0: low
+ 1: high
-Each of brcm,function and brcm,pull may contain either a single value which
+Each of brcm,function, brcm,pull and brcm,level may contain either a single value which
will be applied to all pins in brcm,pins, or 1 value for each entry in
brcm,pins.
diff --git a/drivers/pinctrl/bcm/pinctrl-bcm2835.c b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
index 785c366..0ace548 100644
--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
@@ -73,6 +73,8 @@
enum bcm2835_pinconf_param {
/* argument: bcm2835_pinconf_pull */
BCM2835_PINCONF_PARAM_PULL,
+ /* argument: bcm2835_pinconf_level */
+ BCM2835_PINCONF_PARAM_LEVEL,
};
#define BCM2835_PINCONF_PACK(_param_, _arg_) ((_param_) << 16 | (_arg_))
@@ -725,16 +727,42 @@ static int bcm2835_pctl_dt_node_to_map_pull(struct bcm2835_pinctrl *pc,
return 0;
}
+static int bcm2835_pctl_dt_node_to_map_level(struct bcm2835_pinctrl *pc,
+ struct device_node *np, u32 pin, u32 level,
+ struct pinctrl_map **maps)
+{
+ struct pinctrl_map *map = *maps;
+ unsigned long *configs;
+
+ if (level > 2) {
+ dev_err(pc->dev, "%pOF: invalid brcm,level %d\n", np, level);
+ return -EINVAL;
+ }
+
+ configs = kzalloc(sizeof(*configs), GFP_KERNEL);
+ if (!configs)
+ return -ENOMEM;
+ configs[0] = BCM2835_PINCONF_PACK(BCM2835_PINCONF_PARAM_LEVEL, level);
+
+ map->type = PIN_MAP_TYPE_CONFIGS_PIN;
+ map->data.configs.group_or_pin = bcm2835_gpio_pins[pin].name;
+ map->data.configs.configs = configs;
+ map->data.configs.num_configs = 1;
+ (*maps)++;
+
+ return 0;
+}
+
static int bcm2835_pctl_dt_node_to_map(struct pinctrl_dev *pctldev,
struct device_node *np,
struct pinctrl_map **map, unsigned *num_maps)
{
struct bcm2835_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
- struct property *pins, *funcs, *pulls;
- int num_pins, num_funcs, num_pulls, maps_per_pin;
+ struct property *pins, *funcs, *pulls, *levels;
+ int num_pins, num_funcs, num_pulls, num_levels, maps_per_pin;
struct pinctrl_map *maps, *cur_map;
int i, err;
- u32 pin, func, pull;
+ u32 pin, func, pull, level;
pins = of_find_property(np, "brcm,pins", NULL);
if (!pins) {
@@ -744,6 +772,7 @@ static int bcm2835_pctl_dt_node_to_map(struct pinctrl_dev *pctldev,
funcs = of_find_property(np, "brcm,function", NULL);
pulls = of_find_property(np, "brcm,pull", NULL);
+ levels = of_find_property(np, "brcm,level", NULL);
if (!funcs && !pulls) {
dev_err(pc->dev,
@@ -755,6 +784,7 @@ static int bcm2835_pctl_dt_node_to_map(struct pinctrl_dev *pctldev,
num_pins = pins->length / 4;
num_funcs = funcs ? (funcs->length / 4) : 0;
num_pulls = pulls ? (pulls->length / 4) : 0;
+ num_levels = levels ? (levels->length / 4) : 0;
if (num_funcs > 1 && num_funcs != num_pins) {
dev_err(pc->dev,
@@ -770,11 +800,20 @@ static int bcm2835_pctl_dt_node_to_map(struct pinctrl_dev *pctldev,
return -EINVAL;
}
+ if (num_levels > 1 && num_levels != num_pins) {
+ dev_err(pc->dev,
+ "%pOF: brcm,level must have 1 or %d entries\n",
+ np, num_pins);
+ return -EINVAL;
+ }
+
maps_per_pin = 0;
if (num_funcs)
maps_per_pin++;
if (num_pulls)
maps_per_pin++;
+ if (num_levels)
+ maps_per_pin++;
cur_map = maps = kzalloc(num_pins * maps_per_pin * sizeof(*maps),
GFP_KERNEL);
if (!maps)
@@ -811,6 +850,17 @@ static int bcm2835_pctl_dt_node_to_map(struct pinctrl_dev *pctldev,
if (err)
goto out;
}
+ if (num_levels) {
+ err = of_property_read_u32_index(np, "brcm,level",
+ (num_levels > 1) ? i : 0, &level);
+ if (err)
+ goto out;
+
+ err = bcm2835_pctl_dt_node_to_map_level(pc, np, pin,
+ level, &cur_map);
+ if (err)
+ goto out;
+ }
}
*map = maps;
@@ -931,23 +981,25 @@ static int bcm2835_pinconf_set(struct pinctrl_dev *pctldev,
param = BCM2835_PINCONF_UNPACK_PARAM(configs[i]);
arg = BCM2835_PINCONF_UNPACK_ARG(configs[i]);
- if (param != BCM2835_PINCONF_PARAM_PULL)
+ if (param == BCM2835_PINCONF_PARAM_PULL) {
+ off = GPIO_REG_OFFSET(pin);
+ bit = GPIO_REG_SHIFT(pin);
+
+ bcm2835_gpio_wr(pc, GPPUD, arg & 3);
+ /*
+ * Docs say to wait 150 cycles, but not of what. We assume a
+ * 1 MHz clock here, which is pretty slow...
+ */
+ udelay(150);
+ bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), BIT(bit));
+ udelay(150);
+ bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), 0);
+ } else if (param == BCM2835_PINCONF_PARAM_LEVEL) {
+ /* write in register */
+ bcm2835_gpio_set_bit(pc, arg ? GPSET0 : GPCLR0, pin);
+ } else {
return -EINVAL;
-
- off = GPIO_REG_OFFSET(pin);
- bit = GPIO_REG_SHIFT(pin);
-
- bcm2835_gpio_wr(pc, GPPUD, arg & 3);
- /*
- * BCM2835 datasheet say to wait 150 cycles, but not of what.
- * But the VideoCore firmware delay for this operation
- * based nearly on the same amount of VPU cycles and this clock
- * runs at 250 MHz.
- */
- udelay(1);
- bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), BIT(bit));
- udelay(1);
- bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), 0);
+ }
} /* for each config */
return 0;
--
2.7.4
next reply other threads:[~2018-02-22 18:07 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-02-22 17:44 Matheus Castello [this message]
2018-02-23 14:54 ` Eric Anholt
2018-02-23 15:58 ` Matheus Castello
2018-03-02 10:14 ` Linus Walleij
2018-03-03 14:21 ` Stefan Wahren
2018-03-05 2:29 ` [PATCH v2 0/3] pinctrl: bcm2835: " Matheus Castello
2018-03-05 2:29 ` [PATCH v2 1/3] pinctrl: bcm2835: switch to GENERIC_PINCONF Matheus Castello
2018-03-07 11:51 ` Stefan Wahren
2018-03-05 2:29 ` [PATCH v2 2/3] pinctrl: bcm2835: Add support for generic pinctrl binding Matheus Castello
2018-03-05 23:21 ` Eric Anholt
2018-03-07 3:28 ` Matheus Castello
2018-03-05 2:29 ` [PATCH v2 3/3] pinctrl: bcm2835: Add support for output-low output-high properties Matheus Castello
2018-03-07 11:58 ` [PATCH v2 0/3] pinctrl: bcm2835: Add brcm,level property Stefan Wahren
2018-03-08 0:12 ` Matheus Castello
2018-03-08 8:00 ` Stefan Wahren
2018-03-08 19:47 ` Matheus Castello
2018-03-09 4:16 ` [PATCH v3 " Matheus Castello
2018-03-09 4:16 ` [PATCH v3 1/3] pinctrl: bcm2835: Add support for generic pinctrl binding Matheus Castello
2018-03-09 4:16 ` [PATCH v3 2/3] pinctrl: bcm2835: Add support for output-low output-high properties Matheus Castello
2018-03-09 4:16 ` [PATCH v3 3/3] pinctrl: bcm2835: Update docs about generic pinctrl bindings support Matheus Castello
2018-03-09 11:46 ` Stefan Wahren
2018-03-09 17:13 ` [PATCH v4 0/3] pinctrl: bcm2835: Add generic pinctrl support Matheus Castello
2018-03-09 17:13 ` [PATCH v4 1/3] dt-bindings: pinctrl: bcm2835-gpio: " Matheus Castello
2018-03-18 12:48 ` Rob Herring
2018-03-18 15:23 ` Matheus Castello
2018-04-11 4:58 ` [PATCH v5 0/3] pinctrl: bcm2835: " Matheus Castello
2018-04-11 4:58 ` [PATCH v5 1/3] dt-bindings: pinctrl: bcm2835-gpio: " Matheus Castello
2018-04-11 16:02 ` Eric Anholt
2018-04-16 15:06 ` Rob Herring
2018-04-26 12:21 ` Linus Walleij
2018-04-11 4:58 ` [PATCH v5 2/3] pinctrl: bcm2835: Add support for generic pinctrl binding Matheus Castello
2018-04-21 10:30 ` Stefan Wahren
2018-04-22 12:44 ` Stefan Wahren
2018-04-26 12:24 ` Linus Walleij
2018-04-11 4:58 ` [PATCH v5 3/3] pinctrl: bcm2835: Add support for output-low output-high properties Matheus Castello
2018-04-26 12:25 ` Linus Walleij
2018-04-29 19:28 ` [PATCH v6 0/3] bcm2835: Add generic pinctrl support Matheus Castello
2018-04-29 19:28 ` [PATCH v6 2/3] pinctrl: bcm2835: Add support for generic pinctrl binding Matheus Castello
2018-04-29 19:28 ` [PATCH v6 3/3] pinctrl: bcm2835: Add support for output-low output-high properties Matheus Castello
2018-05-01 0:42 ` [PATCH v7 0/3] bcm2835: Add generic pinctrl support Matheus Castello
2018-05-01 0:42 ` [PATCH v7 2/3] pinctrl: bcm2835: Add support for generic pinctrl binding Matheus Castello
2018-05-03 17:38 ` Stefan Wahren
2018-05-12 9:08 ` Stefan Wahren
2018-05-16 12:00 ` Linus Walleij
2018-05-01 0:42 ` [PATCH v7 3/3] pinctrl: bcm2835: Add support for output-low output-high properties Matheus Castello
2018-05-16 12:02 ` Linus Walleij
2018-03-09 17:13 ` [PATCH v4 2/3] pinctrl: bcm2835: Add support for generic pinctrl binding Matheus Castello
2018-03-12 18:03 ` Eric Anholt
2018-03-09 17:14 ` [PATCH v4 3/3] pinctrl: bcm2835: Add support for output-low output-high properties Matheus Castello
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1519321475-973-1-git-send-email-matheus@castello.eng.br \
--to=matheus@castello.eng.br \
--cc=eric@anholt.net \
--cc=linus.walleij@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=stefan.wahren@i2se.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®