From: Luca Ceresoli <luca@lucaceresoli.net>
To: linux-media@vger.kernel.org
Cc: Luca Ceresoli <luca@lucaceresoli.net>,
Leon Luo <leonl@leopardimaging.com>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
linux-kernel@vger.kernel.org
Subject: [PATCH v2 08/13] media: imx274: consolidate per-mode data in imx274_frmfmt
Date: Tue, 24 Apr 2018 10:24:13 +0200 [thread overview]
Message-ID: <1524558258-530-9-git-send-email-luca@lucaceresoli.net> (raw)
In-Reply-To: <1524558258-530-1-git-send-email-luca@lucaceresoli.net>
Data about the implemented readout modes is partially stored in
imx274_formats[], the rest is scattered in several arrays. The latter
are then accessed using the mode index, e.g.:
min_frame_len[priv->mode_index]
Consolidate all these data in imx274_formats[], and store a pointer to
the selected mode (i.e. imx274_formats[priv->mode_index]) in the main
device struct. This way code to use these data becomes more readable,
e.g.:
priv->mode->min_frame_len
This removes lots of scaffolding code and keeps data about each mode
in a unique place.
Also remove a parameter to imx274_mode_regs() that is now unused.
While this adds the mode pointer to the device struct, it does not
remove the mode_index from it because mode_index is still used in two
dev_dbg() calls. This will be handled in a follow-up commit.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
---
Changed v1 -> v2:
- add "media: " prefix to commit message
---
drivers/media/i2c/imx274.c | 139 +++++++++++++++++++++------------------------
1 file changed, 66 insertions(+), 73 deletions(-)
diff --git a/drivers/media/i2c/imx274.c b/drivers/media/i2c/imx274.c
index 8a8a11b8d75d..2ec31ae4e60d 100644
--- a/drivers/media/i2c/imx274.c
+++ b/drivers/media/i2c/imx274.c
@@ -147,10 +147,28 @@ enum imx274_mode {
};
/*
- * imx274 format related structure
+ * Parameters for each imx274 readout mode.
+ *
+ * These are the values to configure the sensor in one of the
+ * implemented modes.
+ *
+ * @size: recommended recording pixels
+ * @init_regs: registers to initialize the mode
+ * @min_frame_len: Minimum frame length for each mode (see "Frame Rate
+ * Adjustment (CSI-2)" in the datasheet)
+ * @min_SHR: Minimum SHR register value (see "Shutter Setting (CSI-2)" in the
+ * datasheet)
+ * @max_fps: Maximum frames per second
+ * @nocpiop: Number of clocks per internal offset period (see "Integration Time
+ * in Each Readout Drive Mode (CSI-2)" in the datasheet)
*/
struct imx274_frmfmt {
struct v4l2_frmsize_discrete size;
+ const struct reg_8 *init_regs;
+ int min_frame_len;
+ int min_SHR;
+ int max_fps;
+ int nocpiop;
};
/*
@@ -476,58 +494,35 @@ static const struct reg_8 imx274_tp_regs[] = {
{IMX274_TABLE_END, 0x00}
};
-static const struct reg_8 *mode_table[] = {
- [IMX274_MODE_3840X2160] = imx274_mode1_3840x2160_raw10,
- [IMX274_MODE_1920X1080] = imx274_mode3_1920x1080_raw10,
- [IMX274_MODE_1280X720] = imx274_mode5_1280x720_raw10,
-};
-
-/*
- * imx274 format related structure
- */
+/* nocpiop happens to be the same number for the implemented modes */
static const struct imx274_frmfmt imx274_formats[] = {
- { {3840, 2160} },
- { {1920, 1080} },
- { {1280, 720} },
-};
-
-/*
- * minimal frame length for each mode
- * refer to datasheet section "Frame Rate Adjustment (CSI-2)"
- */
-static const int min_frame_len[] = {
- 4550, /* mode 1, 4K */
- 2310, /* mode 3, 1080p */
- 2310 /* mode 5, 720p */
-};
-
-/*
- * minimal numbers of SHR register
- * refer to datasheet table "Shutter Setting (CSI-2)"
- */
-static const int min_SHR[] = {
- 12, /* mode 1, 4K */
- 8, /* mode 3, 1080p */
- 8 /* mode 5, 720p */
-};
-
-static const int max_frame_rate[] = {
- 60, /* mode 1 , 4K */
- 120, /* mode 3, 1080p */
- 120 /* mode 5, 720p */
-};
-
-/*
- * Number of clocks per internal offset period
- * a constant based on mode
- * refer to section "Integration Time in Each Readout Drive Mode (CSI-2)"
- * in the datasheet
- * for the implemented 3 modes, it happens to be the same number
- */
-static const int nocpiop[] = {
- 112, /* mode 1 , 4K */
- 112, /* mode 3, 1080p */
- 112 /* mode 5, 720p */
+ {
+ /* mode 1, 4K */
+ .size = {3840, 2160},
+ .init_regs = imx274_mode1_3840x2160_raw10,
+ .min_frame_len = 4550,
+ .min_SHR = 12,
+ .max_fps = 60,
+ .nocpiop = 112,
+ },
+ {
+ /* mode 3, 1080p */
+ .size = {1920, 1080},
+ .init_regs = imx274_mode3_1920x1080_raw10,
+ .min_frame_len = 2310,
+ .min_SHR = 8,
+ .max_fps = 120,
+ .nocpiop = 112,
+ },
+ {
+ /* mode 5, 720p */
+ .size = {1280, 720},
+ .init_regs = imx274_mode5_1280x720_raw10,
+ .min_frame_len = 2310,
+ .min_SHR = 8,
+ .max_fps = 120,
+ .nocpiop = 112,
+ },
};
/*
@@ -557,6 +552,8 @@ struct imx274_ctrls {
* @regmap: Pointer to regmap structure
* @reset_gpio: Pointer to reset gpio
* @lock: Mutex structure
+ * @mode: Parameters for the selected readout mode
+ * (points to imx274_formats[mode_index])
* @mode_index: Resolution mode index
*/
struct stimx274 {
@@ -569,6 +566,7 @@ struct stimx274 {
struct regmap *regmap;
struct gpio_desc *reset_gpio;
struct mutex lock; /* mutex lock for operations */
+ const struct imx274_frmfmt *mode;
u32 mode_index;
};
@@ -704,18 +702,12 @@ static int imx274_write_table(struct stimx274 *priv, const struct reg_8 table[])
}
/*
- * imx274_mode_regs - Function for set mode registers per mode index
+ * Set mode registers to start stream.
* @priv: Pointer to device structure
- * @mode: Mode index value
- *
- * This is used to start steam per mode index.
- * mode = 0, start stream for sensor Mode 1: 4K/raw10
- * mode = 1, start stream for sensor Mode 3: 1080p/raw10
- * mode = 2, start stream for sensor Mode 5: 720p/raw10
*
* Return: 0 on success, errors otherwise
*/
-static int imx274_mode_regs(struct stimx274 *priv, int mode)
+static int imx274_mode_regs(struct stimx274 *priv)
{
int err = 0;
@@ -727,7 +719,7 @@ static int imx274_mode_regs(struct stimx274 *priv, int mode)
if (err)
return err;
- err = imx274_write_table(priv, mode_table[mode]);
+ err = imx274_write_table(priv, priv->mode->init_regs);
return err;
}
@@ -889,6 +881,7 @@ static int imx274_set_fmt(struct v4l2_subdev *sd,
}
imx274->mode_index = index;
+ imx274->mode = &imx274_formats[index];
if (fmt->width > IMX274_MAX_WIDTH)
fmt->width = IMX274_MAX_WIDTH;
@@ -1042,7 +1035,7 @@ static int imx274_s_stream(struct v4l2_subdev *sd, int on)
if (on) {
/* load mode registers */
- ret = imx274_mode_regs(imx274, imx274->mode_index);
+ ret = imx274_mode_regs(imx274);
if (ret)
goto fail;
@@ -1146,14 +1139,14 @@ static int imx274_clamp_coarse_time(struct stimx274 *priv, u32 *val,
if (err)
return err;
- if (*frame_length < min_frame_len[priv->mode_index])
- *frame_length = min_frame_len[priv->mode_index];
+ if (*frame_length < priv->mode->min_frame_len)
+ *frame_length = priv->mode->min_frame_len;
*val = *frame_length - *val; /* convert to raw shr */
if (*val > *frame_length - IMX274_SHR_LIMIT_CONST)
*val = *frame_length - IMX274_SHR_LIMIT_CONST;
- else if (*val < min_SHR[priv->mode_index])
- *val = min_SHR[priv->mode_index];
+ else if (*val < priv->mode->min_SHR)
+ *val = priv->mode->min_SHR;
return 0;
}
@@ -1365,7 +1358,7 @@ static int imx274_set_exposure(struct stimx274 *priv, int val)
}
coarse_time = (IMX274_PIXCLK_CONST1 / IMX274_PIXCLK_CONST2 * val
- - nocpiop[priv->mode_index]) / hmax;
+ - priv->mode->nocpiop) / hmax;
/* step 2: convert exposure_time into SHR value */
@@ -1375,7 +1368,7 @@ static int imx274_set_exposure(struct stimx274 *priv, int val)
goto fail;
priv->ctrls.exposure->val =
- (coarse_time * hmax + nocpiop[priv->mode_index])
+ (coarse_time * hmax + priv->mode->nocpiop)
/ (IMX274_PIXCLK_CONST1 / IMX274_PIXCLK_CONST2);
dev_dbg(&priv->client->dev,
@@ -1529,10 +1522,9 @@ static int imx274_set_frame_interval(struct stimx274 *priv,
/ frame_interval.numerator);
/* boundary check */
- if (req_frame_rate > max_frame_rate[priv->mode_index]) {
+ if (req_frame_rate > priv->mode->max_fps) {
frame_interval.numerator = 1;
- frame_interval.denominator =
- max_frame_rate[priv->mode_index];
+ frame_interval.denominator = priv->mode->max_fps;
} else if (req_frame_rate < IMX274_MIN_FRAME_RATE) {
frame_interval.numerator = 1;
frame_interval.denominator = IMX274_MIN_FRAME_RATE;
@@ -1634,8 +1626,9 @@ static int imx274_probe(struct i2c_client *client,
/* initialize format */
imx274->mode_index = IMX274_MODE_3840X2160;
- imx274->format.width = imx274_formats[0].size.width;
- imx274->format.height = imx274_formats[0].size.height;
+ imx274->mode = &imx274_formats[imx274->mode_index];
+ imx274->format.width = imx274->mode->size.width;
+ imx274->format.height = imx274->mode->size.height;
imx274->format.field = V4L2_FIELD_NONE;
imx274->format.code = MEDIA_BUS_FMT_SRGGB10_1X10;
imx274->format.colorspace = V4L2_COLORSPACE_SRGB;
--
2.7.4
next prev parent reply other threads:[~2018-04-24 8:27 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-04-24 8:24 [PATCH v2 00/13] media: imx274: cleanups, improvements and SELECTION API support Luca Ceresoli
2018-04-24 8:24 ` [PATCH v2 01/13] media: imx274: document reset delays more clearly Luca Ceresoli
2018-04-24 8:24 ` [PATCH v2 02/13] media: imx274: fix typo in comment Luca Ceresoli
2018-04-24 8:24 ` [PATCH v2 03/13] media: imx274: slightly simplify code Luca Ceresoli
2018-04-24 8:24 ` [PATCH v2 04/13] media: imx274: remove unused data from struct imx274_frmfmt Luca Ceresoli
2018-04-24 8:24 ` [PATCH v2 05/13] media: imx274: rename and reorder register address definitions Luca Ceresoli
2018-04-24 8:24 ` [PATCH v2 06/13] media: imx274: remove non-indexed pointers from mode_table Luca Ceresoli
2018-04-24 8:24 ` [PATCH v2 07/13] media: imx274: initialize format before v4l2 controls Luca Ceresoli
2018-04-24 8:24 ` Luca Ceresoli [this message]
2018-04-24 8:24 ` [PATCH v2 09/13] media: imx274: get rid of mode_index Luca Ceresoli
2018-04-24 17:27 ` kbuild test robot
2018-04-24 8:24 ` [PATCH v2 10/13] media: imx274: actually use IMX274_DEFAULT_MODE Luca Ceresoli
2018-04-24 8:24 ` [PATCH v2 11/13] media: imx274: simplify imx274_write_table() Luca Ceresoli
2018-04-24 8:24 ` [PATCH v2 12/13] media: imx274: add helper function to fill a reg_8 table chunk Luca Ceresoli
2018-04-24 8:24 ` [PATCH v2 13/13] media: imx274: add SELECTION support for cropping Luca Ceresoli
2018-04-24 9:59 ` Sakari Ailus
2018-04-24 14:30 ` Luca Ceresoli
2018-04-26 8:13 ` Sakari Ailus
2018-04-26 13:43 ` Luca Ceresoli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1524558258-530-9-git-send-email-luca@lucaceresoli.net \
--to=luca@lucaceresoli.net \
--cc=leonl@leopardimaging.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®