From: Yannick Fertre <yannick.fertre@st.com>
To: Yannick Fertre <yannick.fertre@st.com>,
Philippe Cornu <philippe.cornu@st.com>,
Benjamin Gaignard <benjamin.gaignard@st.com>,
David Airlie <airlied@linux.ie>, Daniel Vetter <daniel@ffwll.ch>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Alexandre Torgue <alexandre.torgue@st.com>,
<dri-devel@lists.freedesktop.org>,
<linux-stm32@st-md-mailman.stormreply.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>
Subject: [PATCH] drm/bridge/synopsys: dsi: read status error during transfer
Date: Wed, 27 Nov 2019 11:23:13 +0100 [thread overview]
Message-ID: <1574850193-13197-1-git-send-email-yannick.fertre@st.com> (raw)
From: Yannick Fertré <yannick.fertre@st.com>
Read the DSI_INT_ST1 status register to check if
errors occur while reading/writing a command to panel.
In case of error, the transfer is retried 3 times.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
---
drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 99 +++++++++++++++++++++++----
1 file changed, 85 insertions(+), 14 deletions(-)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
index b6e793b..cc806ba 100644
--- a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
+++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
@@ -212,6 +212,20 @@
#define DSI_INT_ST0 0xbc
#define DSI_INT_ST1 0xc0
+#define GPRXE BIT(12)
+#define GPRDE BIT(11)
+#define GPTXE BIT(10)
+#define GPWRE BIT(9)
+#define GCWRE BIT(8)
+#define DPIPLDWE BIT(7)
+#define EOTPE BIT(6)
+#define PSE BIT(5)
+#define CRCE BIT(4)
+#define ECCME BIT(3)
+#define ECCSE BIT(2)
+#define TOLPRX BIT(1)
+#define TOHSTX BIT(0)
+
#define DSI_INT_MSK0 0xc4
#define DSI_INT_MSK1 0xc8
@@ -397,6 +411,42 @@ static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
return 0;
}
+static int dw_mipi_dsi_read_status(struct dw_mipi_dsi *dsi)
+{
+ u32 val;
+
+ val = dsi_read(dsi, DSI_INT_ST1);
+
+ if (val & GPRXE)
+ DRM_DEBUG_DRIVER("DSI Generic payload receive error\n");
+ if (val & GPRDE)
+ DRM_DEBUG_DRIVER("DSI Generic payload read error\n");
+ if (val & GPTXE)
+ DRM_DEBUG_DRIVER("DSI Generic payload transmit error\n");
+ if (val & GPWRE)
+ DRM_DEBUG_DRIVER("DSI Generic payload write error\n");
+ if (val & GCWRE)
+ DRM_DEBUG_DRIVER("DSI Generic command write error\n");
+ if (val & DPIPLDWE)
+ DRM_DEBUG_DRIVER("DSI DPI payload write error\n");
+ if (val & EOTPE)
+ DRM_DEBUG_DRIVER("DSI EoTp error\n");
+ if (val & PSE)
+ DRM_DEBUG_DRIVER("DSI Packet size error\n");
+ if (val & CRCE)
+ DRM_DEBUG_DRIVER("DSI CRC error\n");
+ if (val & ECCME)
+ DRM_DEBUG_DRIVER("DSI ECC multi-bit error\n");
+ if (val & ECCSE)
+ DRM_DEBUG_DRIVER("DSI ECC single-bit error\n");
+ if (val & TOLPRX)
+ DRM_DEBUG_DRIVER("DSI Timeout low-power reception\n");
+ if (val & TOHSTX)
+ DRM_DEBUG_DRIVER("DSI Timeout high-speed transmission\n");
+
+ return val;
+}
+
static int dw_mipi_dsi_write(struct dw_mipi_dsi *dsi,
const struct mipi_dsi_packet *packet)
{
@@ -426,6 +476,12 @@ static int dw_mipi_dsi_write(struct dw_mipi_dsi *dsi,
"failed to get available write payload FIFO\n");
return ret;
}
+
+ val = dw_mipi_dsi_read_status(dsi);
+ if (val) {
+ dev_err(dsi->dev, "dsi status error 0x%0x\n", val);
+ return -EINVAL;
+ }
}
word = 0;
@@ -459,6 +515,12 @@ static int dw_mipi_dsi_read(struct dw_mipi_dsi *dsi,
return ret;
}
+ val = dw_mipi_dsi_read_status(dsi);
+ if (val) {
+ dev_err(dsi->dev, "dsi status error 0x%0x\n", val);
+ return -EINVAL;
+ }
+
val = dsi_read(dsi, DSI_GEN_PLD_DATA);
for (j = 0; j < 4 && j + i < len; j++)
buf[i + j] = val >> (8 * j);
@@ -473,6 +535,7 @@ static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
struct dw_mipi_dsi *dsi = host_to_dsi(host);
struct mipi_dsi_packet packet;
int ret, nb_bytes;
+ int retry = 3;
ret = mipi_dsi_create_packet(&packet, msg);
if (ret) {
@@ -484,24 +547,32 @@ static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
if (dsi->slave)
dw_mipi_message_config(dsi->slave, msg);
- ret = dw_mipi_dsi_write(dsi, &packet);
- if (ret)
- return ret;
- if (dsi->slave) {
- ret = dw_mipi_dsi_write(dsi->slave, &packet);
+ while (retry--) {
+ ret = dw_mipi_dsi_write(dsi, &packet);
if (ret)
- return ret;
- }
+ continue;
- if (msg->rx_buf && msg->rx_len) {
- ret = dw_mipi_dsi_read(dsi, msg);
- if (ret)
- return ret;
- nb_bytes = msg->rx_len;
- } else {
- nb_bytes = packet.size;
+ if (dsi->slave) {
+ ret = dw_mipi_dsi_write(dsi->slave, &packet);
+ if (ret)
+ continue;
+ }
+
+ if (msg->rx_buf && msg->rx_len) {
+ ret = dw_mipi_dsi_read(dsi, msg);
+ if (ret)
+ continue;
+ nb_bytes = msg->rx_len;
+
+ } else {
+ nb_bytes = packet.size;
+ }
+ break;
}
+ if (ret)
+ return ret;
+
return nb_bytes;
}
--
2.7.4
next reply other threads:[~2019-11-27 10:23 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-27 10:23 Yannick Fertre [this message]
2019-11-27 12:07 ` Angelo Ribeiro
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1574850193-13197-1-git-send-email-yannick.fertre@st.com \
--to=yannick.fertre@st.com \
--cc=airlied@linux.ie \
--cc=alexandre.torgue@st.com \
--cc=benjamin.gaignard@st.com \
--cc=daniel@ffwll.ch \
--cc=dri-devel@lists.freedesktop.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=philippe.cornu@st.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®