From: Li Yang <leoyang.li@nxp.com>
To: shawnguo@kernel.org, linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org, Li Yang <leoyang.li@nxp.com>
Subject: [PATCH 05/15] arm64: defconfig: Enable ENETC Ethernet controller and FELIX switch
Date: Mon, 24 Feb 2020 17:08:00 -0600 [thread overview]
Message-ID: <1582585690-463-6-git-send-email-leoyang.li@nxp.com> (raw)
In-Reply-To: <1582585690-463-1-git-send-email-leoyang.li@nxp.com>
Enables drivers for NXP ENETC Ethernet controller and FELIX Ethernet
switch used on QorIQ LS1028a SoC.
The ENETC ethernet drivers are enabled as built-in to boot from network
without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
---
arch/arm64/configs/defconfig | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 9eaf0993cca5..7390c8f3838d 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -154,6 +154,7 @@ CONFIG_IP6_NF_NAT=m
CONFIG_IP6_NF_TARGET_MASQUERADE=m
CONFIG_BRIDGE=m
CONFIG_BRIDGE_VLAN_FILTERING=y
+CONFIG_NET_DSA=m
CONFIG_VLAN_8021Q=m
CONFIG_VLAN_8021Q_GVRP=y
CONFIG_VLAN_8021Q_MVRP=y
@@ -256,6 +257,7 @@ CONFIG_MACVTAP=m
CONFIG_TUN=y
CONFIG_VETH=m
CONFIG_VIRTIO_NET=y
+CONFIG_NET_DSA_MSCC_FELIX=m
CONFIG_AMD_XGBE=y
CONFIG_NET_XGENE=y
CONFIG_ATL1C=m
@@ -267,6 +269,8 @@ CONFIG_FEC=y
CONFIG_FSL_FMAN=y
CONFIG_FSL_DPAA_ETH=y
CONFIG_FSL_DPAA2_ETH=y
+CONFIG_FSL_ENETC=y
+CONFIG_FSL_ENETC_VF=y
CONFIG_HIX5HD2_GMAC=y
CONFIG_HNS_DSAF=y
CONFIG_HNS_ENET=y
--
2.17.1
next prev parent reply other threads:[~2020-02-24 23:08 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-02-24 23:07 [PATCH 00/15] Enable drivers for NXP/FSL QorIQ arm64 boards Li Yang
2020-02-24 23:07 ` [PATCH 01/15] arm64: defconfig: run through savedefconfig for ordering Li Yang
2020-02-24 23:07 ` [PATCH 02/15] arm64: defconfig: Enable NXP flexcan driver Li Yang
2020-02-24 23:07 ` [PATCH 03/15] arm64: defconfig: Enable QorIQ DPAA1 drivers Li Yang
2020-02-24 23:07 ` [PATCH 04/15] arm64: defconfig: Enable QorIQ DPAA2 drivers Li Yang
2020-02-24 23:08 ` Li Yang [this message]
2020-02-24 23:08 ` [PATCH 06/15] arm64: defconfig: Enable NXP/FSL SPI controller drivers Li Yang
2020-03-11 5:51 ` Shawn Guo
[not found] ` <CADRPPNQ-VWmVMdBuEUj9RdXAYvt4dhy+scP-EaYbrXj3McSaVQ@mail.gmail.com>
2020-03-11 7:06 ` Shawn Guo
2020-02-24 23:08 ` [PATCH 07/15] arm64: defconfig: Enable QorIQ cpufreq driver Li Yang
2020-03-11 6:12 ` Shawn Guo
2020-03-11 18:54 ` Leo Li
2020-03-12 14:22 ` Shawn Guo
2020-03-12 16:31 ` Leo Li
2020-02-24 23:08 ` [PATCH 08/15] arm64: defconfig: Enable ARM SBSA watchdog driver Li Yang
2020-02-24 23:08 ` [PATCH 09/15] arm64: defconfig: Enable QorIQ IFC NAND controller driver Li Yang
2020-03-11 6:13 ` Shawn Guo
2020-03-11 18:55 ` Leo Li
2020-02-24 23:08 ` [PATCH 10/15] arm64: defconfig: Enable QorIQ GPIO driver Li Yang
2020-02-24 23:08 ` [PATCH 11/15] arm64: defconfig: Enable ARM Mali display driver Li Yang
2020-02-24 23:08 ` [PATCH 12/15] arm64: defconfig: Enable flash device drivers for QorIQ boards Li Yang
2020-02-24 23:08 ` [PATCH 13/15] arm64: defconfig: Enable RTC devices " Li Yang
2020-02-24 23:08 ` [PATCH 14/15] arm64: defconfig: Enable PHY devices used on " Li Yang
2020-02-24 23:08 ` [PATCH 15/15] arm64: defconfig: Enable e1000 device Li Yang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1582585690-463-6-git-send-email-leoyang.li@nxp.com \
--to=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®