From: Satya Priya <quic_c_skakit@quicinc.com>
To: Bjorn Andersson <bjorn.andersson@linaro.org>,
Rob Herring <robh+dt@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>, <swboyd@chromium.org>,
<collinsd@codeurora.org>, <subbaram@codeaurora.org>,
Das Srinagesh <gurus@codeaurora.org>,
<linux-arm-msm@vger.kernel.org>,
"Lee Jones" <lee.jones@linaro.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
Satya Priya <quic_c_skakit@quicinc.com>
Subject: [PATCH V3 4/4] arm64: dts: qcom: sc7280: Add pm8008 regulators support for sc7280-idp
Date: Thu, 28 Oct 2021 20:44:32 +0530 [thread overview]
Message-ID: <1635434072-32055-5-git-send-email-quic_c_skakit@quicinc.com> (raw)
In-Reply-To: <1635434072-32055-1-git-send-email-quic_c_skakit@quicinc.com>
Add pm8008 regulators support for sc7280 idp.
Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
---
Changes in V2:
- As per Stephen's comments, replaced '_' with '-' for node names.
Changes in V3:
- Changed the regulator node names as l1, l2 etc
- Changed "pm8008-regulators" to "regulators"
- Changed "qcom,min-dropout-voltage" to "regulator-min-dropout-voltage-microvolt"
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 103 +++++++++++++++++++++++++++++++
1 file changed, 103 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index d623d71..493575b 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -309,6 +309,97 @@
};
};
+&i2c1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ pm8008_chip: pm8008@8 {
+ compatible = "qcom,pm8008";
+ reg = <0x8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pm8008_active>;
+ };
+
+ pm8008_ldo: pm8008@9 {
+ compatible = "qcom,pm8008";
+ reg = <0x9>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ regulators {
+ compatible = "qcom,pm8008-regulator";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vdd_l1_l2-supply = <&vreg_s8b_1p2>;
+ vdd_l3_l4-supply = <&vreg_s1b_1p8>;
+ vdd_l5-supply = <&vreg_bob>;
+ vdd_l6-supply = <&vreg_bob>;
+ vdd_l7-supply = <&vreg_bob>;
+
+ pm8008_l1: l1@4000 {
+ reg = <0x4000>;
+ regulator-name = "pm8008_l1";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-min-dropout-voltage-microvolt = <96000>;
+ };
+
+ pm8008_l2: l2@4100 {
+ reg = <0x4100>;
+ regulator-name = "pm8008_l2";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-min-dropout-voltage-microvolt = <24000>;
+ };
+
+ pm8008_l3: l3@4200 {
+ reg = <0x4200>;
+ regulator-name = "pm8008_l3";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-min-dropout-voltage-microvolt = <224000>;
+ };
+
+ pm8008_l4: l4@4300 {
+ reg = <0x4300>;
+ regulator-name = "pm8008_l4";
+ regulator-min-microvolt = <1504000>;
+ regulator-max-microvolt = <1600000>;
+ regulator-min-dropout-voltage-microvolt = <0>;
+ };
+
+ pm8008_l5: l5@4400 {
+ reg = <0x4400>;
+ regulator-name = "pm8008_l5";
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-min-dropout-voltage-microvolt = <104000>;
+ };
+
+ pm8008_l6: l6@4500 {
+ reg = <0x4500>;
+ regulator-name = "pm8008_l6";
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-min-dropout-voltage-microvolt = <112000>;
+ };
+
+ pm8008_l7: l7@4600 {
+ reg = <0x4600>;
+ regulator-name = "pm8008_l7";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3544000>;
+ regulator-min-dropout-voltage-microvolt = <96000>;
+ };
+ };
+ };
+};
+
&qfprom {
vcc-supply = <&vreg_l1c_1p8>;
};
@@ -437,6 +528,18 @@
};
};
+&pm8350c_gpios {
+ pm8008-reset {
+ pm8008_active: pm8008-active {
+ pins = "gpio4";
+ function = "normal";
+ bias-disable;
+ output-high;
+ power-source = <0>;
+ };
+ };
+};
+
&qspi_cs0 {
bias-disable;
};
--
2.7.4
next prev parent reply other threads:[~2021-10-28 15:16 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-28 15:14 [PATCH V3 0/4] Add Qualcomm Technologies, Inc. PM8008 regulator driver Satya Priya
2021-10-28 15:14 ` [PATCH V3 1/4] regulator: dt-bindings: Add pm8008 regulator bindings Satya Priya
2021-10-28 20:06 ` Stephen Boyd
2021-11-18 13:58 ` Satya Priya Kakitapalli (Temp)
2021-10-28 15:14 ` [PATCH V3 2/4] dt-bindings: mfd: pm8008: Add pm8008 regulator node Satya Priya
2021-10-28 20:06 ` Stephen Boyd
2021-10-28 15:14 ` [PATCH V3 3/4] regulator: Add a regulator driver for the PM8008 PMIC Satya Priya
2021-10-28 20:19 ` Stephen Boyd
2021-11-18 13:57 ` Satya Priya Kakitapalli (Temp)
2021-10-28 15:14 ` Satya Priya [this message]
2021-10-28 20:40 ` [PATCH V3 4/4] arm64: dts: qcom: sc7280: Add pm8008 regulators support for sc7280-idp Stephen Boyd
2021-11-18 13:50 ` Satya Priya Kakitapalli (Temp)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1635434072-32055-5-git-send-email-quic_c_skakit@quicinc.com \
--to=quic_c_skakit@quicinc.com \
--cc=bjorn.andersson@linaro.org \
--cc=broonie@kernel.org \
--cc=collinsd@codeurora.org \
--cc=devicetree@vger.kernel.org \
--cc=gurus@codeaurora.org \
--cc=lee.jones@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=subbaram@codeaurora.org \
--cc=swboyd@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®