From: justinpopo6@gmail.com
To: davem@davemloft.net, edumazet@google.com, kuba@kernel.org,
pabeni@redhat.com, joalonsof@gmail.com,
jesionowskigreg@gmail.com, jackychou@asix.com.tw,
jannh@google.com, linux-usb@vger.kernel.org,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: f.fainelli@gmail.com, justin.chen@broadcom.com,
Justin Chen <justinpopo6@gmail.com>
Subject: [PATCH v2 1/5] net: usb: ax88179_178a: remove redundant init code
Date: Wed, 20 Jul 2022 17:28:12 -0700 [thread overview]
Message-ID: <1658363296-15734-2-git-send-email-justinpopo6@gmail.com> (raw)
In-Reply-To: <1658363296-15734-1-git-send-email-justinpopo6@gmail.com>
From: Justin Chen <justinpopo6@gmail.com>
Bind and reset are basically doing the same thing. Remove the duplicate
code and have bind call into reset.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
---
drivers/net/usb/ax88179_178a.c | 85 ++----------------------------------------
1 file changed, 4 insertions(+), 81 deletions(-)
diff --git a/drivers/net/usb/ax88179_178a.c b/drivers/net/usb/ax88179_178a.c
index ac2d400..b7098688 100644
--- a/drivers/net/usb/ax88179_178a.c
+++ b/drivers/net/usb/ax88179_178a.c
@@ -164,6 +164,8 @@
#define GMII_PHY_PGSEL_PAGE3 0x0003
#define GMII_PHY_PGSEL_PAGE5 0x0005
+static int ax88179_reset(struct usbnet *dev);
+
struct ax88179_data {
u8 eee_enabled;
u8 eee_active;
@@ -1322,47 +1324,12 @@ static void ax88179_get_mac_addr(struct usbnet *dev)
static int ax88179_bind(struct usbnet *dev, struct usb_interface *intf)
{
- u8 buf[5];
- u16 *tmp16;
- u8 *tmp;
struct ax88179_data *ax179_data = (struct ax88179_data *)dev->data;
- struct ethtool_eee eee_data;
usbnet_get_endpoints(dev, intf);
- tmp16 = (u16 *)buf;
- tmp = (u8 *)buf;
-
memset(ax179_data, 0, sizeof(*ax179_data));
- /* Power up ethernet PHY */
- *tmp16 = 0;
- ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL, 2, 2, tmp16);
- *tmp16 = AX_PHYPWR_RSTCTL_IPRL;
- ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PHYPWR_RSTCTL, 2, 2, tmp16);
- msleep(200);
-
- *tmp = AX_CLK_SELECT_ACS | AX_CLK_SELECT_BCS;
- ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_CLK_SELECT, 1, 1, tmp);
- msleep(100);
-
- /* Read MAC address from DTB or asix chip */
- ax88179_get_mac_addr(dev);
- memcpy(dev->net->perm_addr, dev->net->dev_addr, ETH_ALEN);
-
- /* RX bulk configuration */
- memcpy(tmp, &AX88179_BULKIN_SIZE[0], 5);
- ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_RX_BULKIN_QCTRL, 5, 5, tmp);
-
- dev->rx_urb_size = 1024 * 20;
-
- *tmp = 0x34;
- ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PAUSE_WATERLVL_LOW, 1, 1, tmp);
-
- *tmp = 0x52;
- ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PAUSE_WATERLVL_HIGH,
- 1, 1, tmp);
-
dev->net->netdev_ops = &ax88179_netdev_ops;
dev->net->ethtool_ops = &ax88179_ethtool_ops;
dev->net->needed_headroom = 8;
@@ -1384,46 +1351,7 @@ static int ax88179_bind(struct usbnet *dev, struct usb_interface *intf)
netif_set_tso_max_size(dev->net, 16384);
- /* Enable checksum offload */
- *tmp = AX_RXCOE_IP | AX_RXCOE_TCP | AX_RXCOE_UDP |
- AX_RXCOE_TCPV6 | AX_RXCOE_UDPV6;
- ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_RXCOE_CTL, 1, 1, tmp);
-
- *tmp = AX_TXCOE_IP | AX_TXCOE_TCP | AX_TXCOE_UDP |
- AX_TXCOE_TCPV6 | AX_TXCOE_UDPV6;
- ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_TXCOE_CTL, 1, 1, tmp);
-
- /* Configure RX control register => start operation */
- *tmp16 = AX_RX_CTL_DROPCRCERR | AX_RX_CTL_IPE | AX_RX_CTL_START |
- AX_RX_CTL_AP | AX_RX_CTL_AMALL | AX_RX_CTL_AB;
- ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_RX_CTL, 2, 2, tmp16);
-
- *tmp = AX_MONITOR_MODE_PMETYPE | AX_MONITOR_MODE_PMEPOL |
- AX_MONITOR_MODE_RWMP;
- ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_MONITOR_MOD, 1, 1, tmp);
-
- /* Configure default medium type => giga */
- *tmp16 = AX_MEDIUM_RECEIVE_EN | AX_MEDIUM_TXFLOW_CTRLEN |
- AX_MEDIUM_RXFLOW_CTRLEN | AX_MEDIUM_FULL_DUPLEX |
- AX_MEDIUM_GIGAMODE;
- ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_MEDIUM_STATUS_MODE,
- 2, 2, tmp16);
-
- ax88179_led_setting(dev);
-
- ax179_data->eee_enabled = 0;
- ax179_data->eee_active = 0;
-
- ax88179_disable_eee(dev);
-
- ax88179_ethtool_get_eee(dev, &eee_data);
- eee_data.advertised = 0;
- ax88179_ethtool_set_eee(dev, &eee_data);
-
- /* Restart autoneg */
- mii_nway_restart(&dev->mii);
-
- usbnet_link_change(dev, 0, 0);
+ ax88179_reset(dev);
return 0;
}
@@ -1716,6 +1644,7 @@ static int ax88179_reset(struct usbnet *dev)
/* Read MAC address from DTB or asix chip */
ax88179_get_mac_addr(dev);
+ memcpy(dev->net->perm_addr, dev->net->dev_addr, ETH_ALEN);
/* RX bulk configuration */
memcpy(tmp, &AX88179_BULKIN_SIZE[0], 5);
@@ -1730,12 +1659,6 @@ static int ax88179_reset(struct usbnet *dev)
ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_PAUSE_WATERLVL_HIGH,
1, 1, tmp);
- dev->net->features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
- NETIF_F_RXCSUM;
-
- dev->net->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
- NETIF_F_RXCSUM;
-
/* Enable checksum offload */
*tmp = AX_RXCOE_IP | AX_RXCOE_TCP | AX_RXCOE_UDP |
AX_RXCOE_TCPV6 | AX_RXCOE_UDPV6;
--
2.7.4
next prev parent reply other threads:[~2022-07-21 0:28 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-07-21 0:28 [PATCH v2 0/5] net: usb: ax88179_178a: improvements and bug fixes justinpopo6
2022-07-21 0:28 ` justinpopo6 [this message]
2022-07-21 0:28 ` [PATCH v2 2/5] net: usb: ax88179_178a: clean up pm calls justinpopo6
2022-07-21 0:28 ` [PATCH v2 3/5] net: usb: ax88179_178a: restore state on resume justinpopo6
2022-07-21 0:28 ` [PATCH v2 4/5] net: usb: ax88179_178a: move priv to driver_priv justinpopo6
2022-07-21 0:28 ` [PATCH v2 5/5] net: usb: ax88179_178a: wol optimizations justinpopo6
2022-07-23 4:50 ` [PATCH v2 0/5] net: usb: ax88179_178a: improvements and bug fixes patchwork-bot+netdevbpf
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1658363296-15734-2-git-send-email-justinpopo6@gmail.com \
--to=justinpopo6@gmail.com \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=f.fainelli@gmail.com \
--cc=jackychou@asix.com.tw \
--cc=jannh@google.com \
--cc=jesionowskigreg@gmail.com \
--cc=joalonsof@gmail.com \
--cc=justin.chen@broadcom.com \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®