Re: [PATCH 3/4] regulator: qcom-rpmh: Add missing regulators in PM6350

[Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>]

On 9/18/26 4:21 PM, Luca Weiss wrote:
> Hi Konrad,
> 
> On Wed Sep 2, 2026 at 10:51 AM CEST, Konrad Dybcio wrote:
>> On 9/1/26 10:58 AM, Luca Weiss wrote:
>>> Add the missing smps3-6 and ldo17 definitions. While smps3/5 and ldo17
>>> are not used from the rpmh regulator driver on SM6350, the regulators do
>>> exist, so add them with the types based on the datasheet.

[...]

>>>  static const struct rpmh_vreg_init_data pm6350_vreg_data[] = {
>>>  	RPMH_VREG("smps1",  SMPS, 1,  &pmic5_ftsmps510, "vdd-s1"),
>>>  	RPMH_VREG("smps2",  SMPS, 2,  &pmic5_hfsmps510, "vdd-s2"),
>>> -	/* smps3 - smps5 not configured */
>>> +	RPMH_VREG("smps3",  SMPS, 3,  &pmic5_ftsmps510, "vdd-s3"),
>>> +	RPMH_VREG("smps4",  SMPS, 4,  &pmic5_ftsmps510, "vdd-s4"),
>>> +	RPMH_VREG("smps5",  SMPS, 5,  &pmic5_ftsmps510, "vdd-s5"),
>>> +	RPMH_VREG("smps6",  SMPS, 6,  &pmic5_hfsmps510, "vdd-s6"),
>>>  	RPMH_VREG("ldo1",   LDO,  1,  &pmic5_nldo,      "vdd-l1"),
>>>  	RPMH_VREG("ldo2",   LDO,  2,  &pmic5_pldo,      "vdd-l2-l5-l7"),
>>>  	RPMH_VREG("ldo3",   LDO,  3,  &pmic5_pldo,      "vdd-l3-l6-l8-l9-l10"),
>>> @@ -1608,7 +1611,7 @@ static const struct rpmh_vreg_init_data pm6350_vreg_data[] = {
>>>  	RPMH_VREG("ldo14",  LDO,  14, &pmic5_pldo,      "vdd-l12-l14"),
>>>  	RPMH_VREG("ldo15",  LDO,  15, &pmic5_nldo,      "vdd-l15-l19-l22"),
>>>  	RPMH_VREG("ldo16",  LDO,  16, &pmic5_nldo,      "vdd-l16"),
>>> -	/* ldo17 not configured */
>>> +	RPMH_VREG("ldo17",  LDO,  17, &pmic5_nldo,      "vdd-l17"),
>>
>> L17 (and other NLDOs on this PMIC) can do 0.312 - 1.304 V, whereas
>> the pmic5_nldo config allows a range of 0.32 - 1.296 V. But I suppose
>> that is something to fix separately anyway
> 
> Can you help with what numbers from the data sheet we're supposed to
> use?
> 
> In 80-PR887-1 Rev. G, Table 3-20 would suggest L17 is programmable from
> 0.312V to 1.328V while "output voltage range" is 0.32V-1.304V.
> 
> But Table 3-11 does indeed show 0.312V - 1.304V as "Programming range"
> for this specific LDO.
> 
> So the voltages from the Table 3-11 are the ones to use? The other ones
> can be ignored completely? But e.g. the step size is only listed in
> 3-20.
> 
> Sidenote, are the step sizes for the SMPS listed anywhere?

+Kamal should be able to give you definitive answers here

Konrad