From: Jia Wang <wangjia@ultrarisc.com>
To: Linus Walleij <linusw@kernel.org>
Cc: wangjia@ultrarisc.com, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Bartosz Golaszewski <brgl@kernel.org>,
linux-gpio@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v3 2/2] pinctrl: ultrarisc: Add UltraRISC DP1000 pinctrl driver
Date: Tue, 09 Jun 2026 14:34:24 +0800 [thread overview]
Message-ID: <178098686461.187087.11502108328443255683.b4-reply@b4> (raw)
In-Reply-To: <CAD++jL=LFZYUFyAt9eUMPw02yCXC3cD6h4wvHQ529OS-o-WtSQ@mail.gmail.com>
On 2026-06-09 00:23 +0200, Linus Walleij wrote:
> Hi Jia,
>
> thanks for your patch!
>
> On Mon, Jun 8, 2026 at 9:50 AM Jia Wang via B4 Relay
> <devnull+wangjia.ultrarisc.com@kernel.org> wrote:
>
> > From: Jia Wang <wangjia@ultrarisc.com>
> >
> > Add support for the pin controller on the UltraRISC DP1000 SoC.
> >
> > The controller provides mux selection for pins in ports A, B, C, D, and
> > LPC. Ports A-D default to GPIO and support peripheral muxing. LPC pins
> > can be switched to eSPI, but are not available as GPIOs. Basic pin
> > configuration controls such as drive strength, pull-up, and pull-down
> > are also supported.
> >
> > Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
>
> Overall this looks very good, some things to fix up below but nothing
> major!
>
Thanks for the review.
> (...)
> > +config PINCTRL_ULTRARISC
> > + tristate
> > + depends on OF
> > + depends on ARCH_ULTRARISC || COMPILE_TEST
> > + select GENERIC_PINCTRL
> > + select PINMUX
> > + select GPIOLIB
>
> Why GPIOLIB? You don't implement any GPIO chips...
>
Good catch. GPIOLIB is not actually needed here since the driver does not
provide any GPIO functionality. I'll drop the select in the next version.
> > + raw_spin_lock_irqsave(&pctrl->lock, flags);
> > + val = readl_relaxed(reg);
> > + val = (val & ~mask) | field_prep(mask, conf);
> > + writel_relaxed(val, reg);
> > + raw_spin_unlock_irqrestore(&pctrl->lock, flags);
>
> Have you thought about using a scoped guard for this lock?
> It will make the code easier to read.
> (Applies everywhere.)
>
Yes, that makes sense. I'll convert the lock sections to use scoped_guard()
throughout the driver in the next version.
> > +static int ur_find_group_route(struct ur_pinctrl *pctrl,
> > + const char *function,
> > + u64 group_mask,
> > + const struct ur_func_route **route_out)
> > +{
> > + const struct ur_func_route *match = NULL;
> > +
> > + for (u32 i = 0; i < pctrl->data->num_routes; i++) {
> > + const struct ur_func_route *route = &pctrl->data->routes[i];
> > +
> > + if (strcmp(route->function, function))
> > + continue;
> > +
> > + if ((route->valid_pins & group_mask) != group_mask)
> > + continue;
> > +
> > + if (match) {
> > + dev_err(pctrl->dev,
> > + "ambiguous route for function %s group_mask=%#llx\n",
> > + function, (unsigned long long)group_mask);
> > + return -EINVAL;
> > + }
> > +
> > + match = route;
> > + }
> > +
> > + if (match) {
> > + *route_out = match;
> > + return 0;
> > + }
> > +
> > + return -EINVAL;
> > +}
>
> This routing function needs some kind of comment before it explaining
> what is going on and what constraints you are trying to resolve with this.
>
Agreed. I'll add a comment describing the routing model and the constraints
being resolved here.
> > +static bool ur_function_is_gpio(struct pinctrl_dev *pctldev,
> > + unsigned int selector)
>
> Neat that you implement this!
>
Thanks.
> > +static const struct pinctrl_ops ur_pinctrl_ops = {
> > + .get_groups_count = pinctrl_generic_get_group_count,
> > + .get_group_name = pinctrl_generic_get_group_name,
> > + .get_group_pins = pinctrl_generic_get_group_pins,
> > + .dt_node_to_map = pinctrl_generic_pins_function_dt_node_to_map,
> > + .dt_free_map = pinconf_generic_dt_free_map,
> > +};
>
> Good use of generic helpers!
>
> > +static const struct pinmux_ops ur_pinmux_ops = {
> > + .get_functions_count = pinmux_generic_get_function_count,
> > + .get_function_name = pinmux_generic_get_function_name,
> > + .get_function_groups = pinmux_generic_get_function_groups,
> > + .function_is_gpio = ur_function_is_gpio,
> > + .set_mux = ur_set_mux,
> > + .gpio_request_enable = ur_gpio_request_enable,
> > + .strict = true,
> > +};
>
> Here too.
>
> > +static const struct pinconf_ops ur_pinconf_ops = {
> > + .pin_config_get = ur_pin_config_get,
> > + .pin_config_set = ur_pin_config_set,
> > + .pin_config_group_get = ur_pin_config_group_get,
> > + .pin_config_group_set = ur_pin_config_group_set,
> > +#ifdef CONFIG_GENERIC_PINCONF
> > + .is_generic = true,
> > + .pin_config_config_dbg_show = pinconf_generic_dump_config,
> > +#endif
>
> Why ifdef:ed? Just select it in your Kconfig and rely on it?
>
GENERIC_PINCONF is already selected via GENERIC_PINCTRL, so the dependency
is guaranteed. The ifdef is therefore unnecessary; I'll remove it in the
next version.
> Yours,
> Linus Walleij
>
Best regards,
Jia Wang
prev parent reply other threads:[~2026-06-09 6:34 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-06-08 7:50 [PATCH v3 0/2] pinctrl: ultrarisc: add DP1000 pinctrl support Jia Wang via B4 Relay
2026-06-08 7:50 ` [PATCH v3 1/2] dt-bindings: pinctrl: Add UltraRISC DP1000 pinctrl controller Jia Wang via B4 Relay
2026-06-08 17:17 ` Conor Dooley
2026-06-09 2:07 ` Jia Wang
2026-06-08 7:50 ` [PATCH v3 2/2] pinctrl: ultrarisc: Add UltraRISC DP1000 pinctrl driver Jia Wang via B4 Relay
2026-06-08 22:23 ` Linus Walleij
2026-06-09 6:34 ` Jia Wang [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=178098686461.187087.11502108328443255683.b4-reply@b4 \
--to=wangjia@ultrarisc.com \
--cc=brgl@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linusw@kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®