[PATCH v3] drm/i915/hdmi: preserve cached EDID on DDC failure when connector is forced

[Aman Sharma <amansharma6122002@gmail.com>]

When an HDMI connector is forced enabled (e.g. via video=HDMI-A-1:e for
laptop clamshell operation) and the external monitor enters DPMS standby,
some monitors (such as the BenQ GW2790Q) power down their internal DDC/I2C
controller, causing SCDC/EDID reads to fail with -ENXIO (-6).

Currently, intel_hdmi_detect() and intel_hdmi_force() unconditionally call
intel_hdmi_unset_edid() before calling intel_hdmi_set_edid(). When
drm_edid_read_ddc() returns NULL during monitor standby, the connector's
cached detect_edid is wiped out and
drm_helper_probe_single_connector_modes() falls back to the 1024x768 VESA
no-EDID mode. When the monitor wakes back up, because the connector status
remained forced to connector_status_connected, no hotplug state transition
occurs and the display remains stuck at 1024x768 until a manual mode probe
(such as toggling the laptop lid) is triggered.

Fix this by moving intel_hdmi_unset_edid() into intel_hdmi_set_edid() after
checking whether a forced-on connector (DRM_FORCE_ON or
DRM_FORCE_ON_DIGITAL) already has a valid cached EDID (detect_edid and
edid_blob_ptr) when DDC fails, and preserving connector_status_connected
on Gen11+ digital port disconnect when a forced-on connector has a cached
EDID. When the monitor is awake or a different monitor is plugged in,
drm_edid_read_ddc() succeeds, resets the previous EDID and dp_dual_mode
state via intel_hdmi_unset_edid(), and updates the connector with the new
EDID.

v3:
- Explicitly check for DRM_FORCE_ON / DRM_FORCE_ON_DIGITAL so DRM_FORCE_OFF
  still clears the cached EDID as expected.
- Report connector_status_connected on Gen11+ disconnect when a forced-on
  connector retains its cached EDID, and jump to out in
  intel_hdmi_set_edid() so CEC physical address remains valid and
  drm_helper_probe_detect_ctx() does not increment epoch_counter on
  standby HPD pulses.

v2:
- Move intel_hdmi_unset_edid() into intel_hdmi_set_edid() so hotplug
  detection via intel_hdmi_detect() also preserves the cached EDID on
  forced connectors and resets dp_dual_mode when updating EDID.
- Clear detect_edid on Gen11+ disconnect when the connector is unforced,
  and verify edid_blob_ptr is non-NULL before retaining detect_edid.

Signed-off-by: Aman Sharma <amansharma6122002@gmail.com>
---
 drivers/gpu/drm/i915/display/intel_hdmi.c | 31 ++++++++++++++++++-----
 1 file changed, 25 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/i915/display/intel_hdmi.c b/drivers/gpu/drm/i915/display/intel_hdmi.c
index b6fa1a1558b8..a14a857dfe94 100644
--- a/drivers/gpu/drm/i915/display/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/display/intel_hdmi.c
@@ -2570,6 +2570,21 @@ intel_hdmi_set_edid(struct drm_connector *_connector)
 		intel_gmbus_force_bit(ddc, false);
 	}
 
+	/*
+	 * If the connector is forced on (e.g. video=HDMI-A-1:e) and the sink's
+	 * DDC/I2C bus is powered down during DPMS standby, keep the previously
+	 * cached EDID rather than wiping it and falling back to 1024x768.
+	 */
+	if (!drm_edid &&
+	    (connector->base.force == DRM_FORCE_ON ||
+	     connector->base.force == DRM_FORCE_ON_DIGITAL) &&
+	    connector->detect_edid && connector->base.edid_blob_ptr) {
+		connected = true;
+		goto out;
+	}
+
+	intel_hdmi_unset_edid(&connector->base);
+
 	/* Below we depend on display info having been updated */
 	drm_edid_connector_update(&connector->base, drm_edid);
 
@@ -2580,6 +2595,7 @@ intel_hdmi_set_edid(struct drm_connector *_connector)
 		connected = true;
 	}
 
+out:
 	intel_display_power_put(display, POWER_DOMAIN_GMBUS, wakeref);
 
 	cec_notifier_set_phys_addr(intel_hdmi->cec_notifier,
@@ -2611,10 +2627,15 @@ intel_hdmi_detect(struct drm_connector *_connector, bool force)
 	wakeref = intel_display_power_get(display, POWER_DOMAIN_GMBUS);
 
 	if (DISPLAY_VER(display) >= 11 &&
-	    !intel_digital_port_connected(encoder))
+	    !intel_digital_port_connected(encoder)) {
+		if ((connector->base.force == DRM_FORCE_ON ||
+		     connector->base.force == DRM_FORCE_ON_DIGITAL) &&
+		    connector->detect_edid && connector->base.edid_blob_ptr)
+			status = connector_status_connected;
+		else
+			intel_hdmi_unset_edid(&connector->base);
 		goto out;
-
-	intel_hdmi_unset_edid(&connector->base);
+	}
 
 	if (intel_hdmi_set_edid(&connector->base))
 		status = connector_status_connected;
@@ -2638,10 +2659,10 @@ intel_hdmi_force(struct drm_connector *_connector)
 	if (!intel_display_driver_check_access(display))
 		return;
 
-	intel_hdmi_unset_edid(&connector->base);
-
-	if (connector->base.status != connector_status_connected)
+	if (connector->base.status != connector_status_connected) {
+		intel_hdmi_unset_edid(&connector->base);
 		return;
+	}
 
 	intel_hdmi_set_edid(&connector->base);
 }
-- 
2.43.0