From: Tang Yizhou <tangyeechou@gmail.com>
To: Jun Yang <littleddfu@gmail.com>,
Miklos Szeredi <miklos@szeredi.hu>,
fuse-devel@lists.linux.dev
Cc: Zhao Chen <winters.zc@antgroup.com>,
linux-kernel@vger.kernel.org, Jun Yang <junvyyang@tencent.com>,
TencentOS Corvus AI <corvus@tencent.com>
Subject: Re: [PATCH 0/2] fuse: fix request lifetime races in the resend path
Date: Fri, 14 Aug 2026 14:19:40 +0800 [thread overview]
Message-ID: <1bc066fa-ee8c-426a-9c63-b0ee305de5a5@gmail.com> (raw)
In-Reply-To: <20260804091757.503476-1-junvyyang@tencent.com>
On 4/8/26 5:17 pm, Jun Yang wrote:
> Two fixes for races introduced together with FUSE_NOTIFY_RESEND
> (760eac73f9f6, v6.9), where fuse_chan_resend() moves in-flight requests
> from fpq->processing back onto fiq->pending.
>
> Both concern the same invariant. FR_PENDING means "queued on fiq->pending,
> protected by fiq->lock", and it is what fuse_remove_pending_req() relies on
Hi,
Currently FR_PENDING doesn't mean the request is protected by fiq->lock. It
looks like this is your solution, so you need to clearly explain why you are
doing this.
> to unlink a request and drop the queue's reference. A request on
It is unrelated to the queue's reference. I think you need to check whether the
AI's output is correct first.
> fiq->pending can therefore be released without going through
> fuse_request_end(), so anything that sets FR_PENDING, or that leaves a
> request linked elsewhere while FR_PENDING is set, has to be done under
> fiq->lock.
>
> Patch 1 sets FR_PENDING under fiq->lock. fuse_chan_resend() currently
> publishes the bit while the requests are reachable only through a
> stack-local list, so a concurrent waiter can unlink and release a request
> that fuse_chan_resend() is still iterating over.
>
> Patch 2 re-checks FR_SENT under fiq->lock in fuse_dev_queue_interrupt().
> Its callers sample FR_SENT unlocked and fuse_chan_resend() clears it under
> fiq->lock, so a request can end up queued on fiq->pending and linked on
> fiq->interrupts at the same time.
>
> Dependency between the two patches
> ==================================
>
> They are independent and neither supersedes the other, so please apply them
> together rather than picking one. Patch 2 does not affect the unlocked
> FR_PENDING publish that patch 1 fixes. Patch 1 cannot catch an intr_entry
> that is linked after its locked walk has already run, because that link
> happens once fuse_chan_resend() has released fiq->lock. Patch 1 on its own
> also makes the condition patch 2 fixes easier to hit, since requests that
> would previously have been torn out of the resend list now survive to be
> re-queued.
>
> Both were found by code audit and confirmed on v7.2-rc6 (075b74841bd0),
> where the series was built and tested; the resend and interrupt paths were
> verified to still be exercised with the series applied.
>
> A KASAN reproducer for this issue is available if requested.
Since you have a KASAN reproducer, please first describe how to trigger the
issue and what the symptoms are, as a prelude to the solution.
--
Best Regards,
Yi
>
> Reported-by: TencentOS Corvus AI <corvus@tencent.com>
> Signed-off-by: Jun Yang <junvyyang@tencent.com>
>
> Jun Yang (2):
> fuse: set FR_PENDING under fiq->lock in fuse_chan_resend()
> fuse: don't queue an interrupt for a request that is back on
> fiq->pending
>
> fs/fuse/dev.c | 29 +++++++++++++++--------------
> 1 file changed, 15 insertions(+), 14 deletions(-)
>
prev parent reply other threads:[~2026-08-14 6:19 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-08-04 9:17 Jun Yang
2026-08-04 9:17 ` [PATCH 1/2] fuse: set FR_PENDING under fiq->lock in fuse_chan_resend() Jun Yang
2026-08-14 7:23 ` Tang Yizhou
2026-08-04 9:17 ` [PATCH 2/2] fuse: don't queue an interrupt for a request that is back on fiq->pending Jun Yang
2026-08-14 8:49 ` Tang Yizhou
2026-08-14 6:19 ` Tang Yizhou [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1bc066fa-ee8c-426a-9c63-b0ee305de5a5@gmail.com \
--to=tangyeechou@gmail.com \
--cc=corvus@tencent.com \
--cc=fuse-devel@lists.linux.dev \
--cc=junvyyang@tencent.com \
--cc=linux-kernel@vger.kernel.org \
--cc=littleddfu@gmail.com \
--cc=miklos@szeredi.hu \
--cc=winters.zc@antgroup.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®