From: Marko Rebrina <mrebrina@jagor.srce.hr>
To: linux-kernel@vger.kernel.org
Subject: PROBLEM:blinking screen in XFree4.x !
Date: Mon, 16 Jul 2001 19:33:01 +0200 [thread overview]
Message-ID: <20010716193301.A2161@debelian.doma.hr> (raw)
Hi,
I have problem with XFree4.x(current 4.1) when I have large file transfer(~1GB)
then screen in X start blinking(black screen),console works fine!
Restarting Xe not resolving problem! No message in log !
I have K7-700Mhz/AbitKA7(KX133)/256M/G400DH32M
Kernel:2.4.x,current 2.4.6
%cat /proc/modules
nls_iso8859-1 2880 0 (autoclean)
nls_iso8859-2 3392 1 (autoclean)
nls_cp437 4384 1 (autoclean)
vmnet 18752 0 (unused)
vmmon 19152 0 (unused)
8139too 11936 1
hisax 134224 5
isdn 119984 6 [hisax]
slhc 5024 2 [isdn]
cmpci 23664 2
%cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(set)
0778-077a : parport0
0cf8-0cff : PCI conf1
4000-40ff : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
5000-500f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
6000-607f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
d000-d00f : VIA Technologies, Inc. Bus Master IDE
d000-d007 : ide0
d008-d00f : ide1
d400-d41f : VIA Technologies, Inc. UHCI USB
d400-d41f : usb-uhci
d800-d81f : VIA Technologies, Inc. UHCI USB (#2)
d800-d81f : usb-uhci
dc00-dcff : Realtek Semiconductor Co., Ltd. RTL-8139
dc00-dcff : 8139too
e000-e007 : PCI device 1043:0675 (Asustek Computer, Inc.)
e400-e4ff : C-Media Electronics Inc CM8738
e400-e4ff : cmpci
%cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-0ffeffff : System RAM
00100000-0023e7d3 : Kernel code
0023e7d4-002b055f : Kernel data
0fff0000-0fff2fff : ACPI Non-volatile Storage
0fff3000-0fffffff : ACPI Tables
d0000000-d7ffffff : VIA Technologies, Inc. VT8371 [KX133]
d8000000-dbffffff : PCI Bus #01
d8000000-d8003fff : Matrox Graphics, Inc. MGA G400 AGP
d9000000-d97fffff : Matrox Graphics, Inc. MGA G400 AGP
dc000000-ddffffff : PCI Bus #01
dc000000-ddffffff : Matrox Graphics, Inc. MGA G400 AGP
de000000-de0000ff : Realtek Semiconductor Co., Ltd. RTL-8139
de000000-de0000ff : 8139too
de001000-de0010ff : PCI device 1043:0675 (Asustek Computer, Inc.)
ffff0000-ffffffff : reserved
%lspci -vvv
00:00.0 Host bridge: VIA Technologies, Inc. VT8371 [KX133] (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: VIA Technologies, Inc. VT8371 [KX133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d8000000-dbffffff
Prefetchable memory behind bridge: dc000000-ddffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 21)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 3
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at dc00 [size=256]
Region 1: Memory at de000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
00:0b.0 Network controller: Asustek Computer, Inc.: Unknown device 0675 (rev 02)
Subsystem: Dynalink: Unknown device 1704
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16 (4000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e000 [disabled] [size=8]
Region 1: Memory at de001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:0f.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at e400 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 05) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G400 MAX/Dual Head 32Mb
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at dc000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at d8000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at d9000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
--
-o) // Marko Rebrina, http://jagor.srce.hr/~mrebrina, ICQ:20358351 \\
/\\
_\_v Serving FREE beer to the users of the FREE Linux of a FREE world
next reply other threads:[~2001-07-16 17:37 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-07-16 17:33 Marko Rebrina [this message]
2001-07-16 18:28 ` Jeffrey W. Baker
2001-07-16 19:25 ` George
2001-07-16 19:34 ` Marko Rebrina
[not found] <200107170721.JAA0000038245@greve.tasking.nl>
2001-07-17 9:46 ` Marko Rebrina
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20010716193301.A2161@debelian.doma.hr \
--to=mrebrina@jagor.srce.hr \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®