From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id ; Mon, 20 Aug 2001 04:26:24 -0400 Received: (majordomo@vger.kernel.org) by vger.kernel.org id ; Mon, 20 Aug 2001 04:26:15 -0400 Received: from [203.161.228.202] ([203.161.228.202]:12294 "EHLO spf1.hq.outblaze.com") by vger.kernel.org with ESMTP id ; Mon, 20 Aug 2001 04:25:57 -0400 Date: 20 Aug 2001 08:36:30 -0000 Message-ID: <20010820083630.16182.qmail@yusufg.portal2.com> From: Yusuf Goolamabbas To: linux-kernel@vger.kernel.org Subject: aic7xxx errors with 2.4.8-ac7 on 440gx mobo Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org Hi, 2.4.8 and 2.4.9 have no problems compiling and booting on a P3 500 440GX mobo (APIC not compiled in the kernel) With 2.4.8-ac7, I get SCSI errors and the kernel fails to boot. If I compile with APIC enabled and APIC on UP also enabled, it boots cleanly booting with append="noapic", gives the same errors SCSI subsystem driver Revision: 1.00 PCI: Assigned IRQ 11 for device 00:0c.0 PCI: Sharing IRQ 11 with 00:0c.1 PCI: Found IRQ 11 for device 00:0c.1 PCI: Sharing IRQ 11 with 00:0c.0 scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1 aic7896/97: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1 aic7896/97: Ultra2 Wide Channel B, SCSI Id=7, 32/255 SCBs scsi0:0:0:0: Attempting to queue an ABORT message scsi0:0:0:0: Command already completed aic7xxx_abort returns 8194 scsi0:0:0:0: Attempting to queue an ABORT message scsi0:0:0:0: Device is active, asserting ATN Recovery code sleeping Recovery code awake Timer Expired aic7xxx_abort returns 8195 scsi0:0:0:0: Attempting to queue a TARGET RESET message aic7xxx_dev_reset returns 8195 Recovery SCB completes scsi0:0:0:0: Attempting to queue an ABORT message ahc_intr: HOST_MSG_LOOP bad phase 0x0 scsi0:0:0:0: Cmd aborted from QINFIFO aic7xxx_abort returns 8194 scsi: device set offline - not ready or command retry failed after bus reset: host 0 channel 0 id 0 lun 0 scsi0:0:1:0: Attempting to queue an ABORT message scsi0:0:1:0: Command already completed aic7xxx_abort returns 8194 scsi0:0:1:0: Attempting to queue an ABORT message scsi0:0:1:0: Command already completed aic7xxx_abort returns 8194 scsi0:0:1:0: Attempting to queue a TARGET RESET message scsi0:0:1:0: Is not an active device scsi0:0:1:0: Attempting to queue an ABORT message scsi0:0:1:0: Command already completed aic7xxx_abort returns 8194 Regards, Yusuf