From: Jan Marek <linux@hazard.jcu.cz>
To: David Woodhouse <dwmw2@infradead.org>
Cc: linux-kernel <linux-kernel@vger.kernel.org>
Subject: Re: Cannot unlock spinlock... Was: Problem in yenta.c, 2nd edition
Date: Wed, 7 Nov 2001 11:10:56 +0100 [thread overview]
Message-ID: <20011107111056.E11351@hazard.jcu.cz> (raw)
In-Reply-To: <20011107104044.C11351@hazard.jcu.cz> <20011106123427.A11351@hazard.jcu.cz> <3BE2D37A.D32C6DB1@zip.com.au> <20011105112900.C5919@hazard.jcu.cz> <23001.1005086449@redhat.com> <11670.1005127189@redhat.com> <20011107110702.D11351@hazard.jcu.cz>
In-Reply-To: <20011107110702.D11351@hazard.jcu.cz>
[-- Attachment #1: Type: text/plain, Size: 272 bytes --]
Hallo,
> I have ACPI enabled and I'm attaching my lspci -vvv... Thank you
> very much...
I'm sorry, I don't remember to attach this file... One's more...
>
> > --
> > dwmw2
--
Ing. Jan Marek
University of South Bohemia
Academic Computer Centre
Phone: +420-38-7772080
[-- Attachment #2: lsp --]
[-- Type: text/plain, Size: 4582 bytes --]
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (AGP disabled) (rev 03)
Subsystem: Compaq Computer Corporation: Unknown device b110
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at 50000000 (32-bit, prefetchable) [size=256M]
00:04.0 CardBus bridge: Texas Instruments PCI1211
Subsystem: Compaq Computer Corporation: Unknown device b103
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 7fffe000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=176
Memory window 0: 10000000-103ff000 (prefetchable)
Memory window 1: 10400000-107ff000
I/O window 0: 00004400-000044ff
I/O window 1: 00004800-000048ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:05.0 VGA compatible controller: ATI Technologies Inc 3D Rage LT Pro (rev dc) (prog-if 00 [VGA])
Subsystem: Compaq Computer Corporation: Unknown device b11b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 41000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at 40280000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 Bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 3820 [size=16]
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 3800 [size=32]
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:08.0 Multimedia audio controller: ESS Technology ES1978 Maestro 2E (rev 10)
Subsystem: Compaq Computer Corporation: Unknown device b112
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 3400 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Communication controller: Lucent Microelectronics WinModem 56k (rev 01)
Subsystem: Compaq Computer Corporation 56k V.90 Modem
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 40000000 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at 2400 [size=8]
Region 2: I/O ports at 2000 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
next prev parent reply other threads:[~2001-11-07 10:12 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <3BE2D37A.D32C6DB1@zip.com.au>
2001-11-05 10:29 ` [Fwd: Re: Problem in yenta.c, 2nd edition] Jan Marek
2001-11-06 11:34 ` Cannot unlock spinlock... Was: Problem in yenta.c, 2nd edition Jan Marek
2001-11-06 22:40 ` David Woodhouse
2001-11-07 9:40 ` Jan Marek
2001-11-07 9:59 ` David Woodhouse
2001-11-07 10:07 ` Jan Marek
2001-11-07 10:10 ` Jan Marek [this message]
2001-11-07 10:30 ` Alan Cox
2001-11-07 10:29 ` David Woodhouse
2001-11-07 10:47 ` Alan Cox
2001-11-07 10:55 ` Jan Marek
2001-11-07 15:04 ` Doug McNaught
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20011107111056.E11351@hazard.jcu.cz \
--to=linux@hazard.jcu.cz \
--cc=dwmw2@infradead.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®