mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Thomas Deselaers <thomas@deselaers.de>
To: linux-kernel@vger.kernel.org
Subject: Re: IDE Harddrive Performance
Date: Wed, 19 Dec 2001 17:05:29 +0100	[thread overview]
Message-ID: <20011219160529.GA3930@leukertje.hitnet.rwth-aachen.de> (raw)
In-Reply-To: <20011219153233.GA3424@leukertje.hitnet.rwth-aachen.de> <20011219155538.BF29F3B92@dnph.phys.msu.su>
In-Reply-To: <20011219155538.BF29F3B92@dnph.phys.msu.su>

On Wed, Dec 19, 2001 at 06:55:38PM +0300, Oleg Artamonov wrote:
> Thomas Deselaers ???????:
> > /dev/hdc:
> >  Timing buffered disk reads:  64 MB in  5.63 seconds = 11.37 MB/sec
> >
> > What would be a value I can expect from my hardware?
> 
>   I have a Maxtor D541X (20Gbytes, 5400rpm), and its results are about 
> 37MB/sec... Motherboard is Epox 8KTA3 with VIA 686B southbridge (HDD runs in 
> UDMA5 mode).
> 
> > And what might result in higher speeds?
> 
>   Did you enable UltraDMA2 (P2B-S supports only UDMA2, not UDMA4 nor UDMA5)? 
> 32-bit transfer? What 'hdparm /dev/hda' and 'hdpram -i /dev/hda' says?

Here are the results, and maybe I should have told, that I am using 2.4.16
without any further patches applied. 

It seems that I have udma2 enabled.

leukertje:/home/thomasd# hdparm /dev/hdc

/dev/hdc:
 multcount    = 16 (on)
 I/O support  =  0 (default 16-bit)
 unmaskirq    =  0 (off)
 using_dma    =  1 (on)
 keepsettings =  0 (off)
 nowerr       =  0 (off)
 readonly     =  0 (off)
 readahead    =  8 (on)
 geometry     = 7297/255/63, sectors = 117231408, start = 0
 busstate     =  1 (on)
leukertje:/home/thomasd# hdparm -i /dev/hdc

/dev/hdc:

 Model=MAXTOR 4K060H3, FwRev=A08.1500, SerialNo=373120024159
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=32256, SectSize=21298, ECCbytes=4
 BuffType=DualPortCache, BuffSize=2000kB, MaxMultSect=16, MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=117231408
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes: pio0 pio1 pio2 pio3 pio4 
 DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 
 AdvancedPM=no WriteCache=enabled
 Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4
ATA-5 


thomas

-- 
thomas@deselaers.de «<>» JabberID on request «<>» GPG/PGP key on request
  «< Unless stated otherwise everything I write is just my opinion >»

  reply	other threads:[~2001-12-19 16:05 UTC|newest]

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2001-12-19 15:32 Thomas Deselaers
2001-12-19 15:44 ` Brendan Pike
2001-12-19 15:55   ` Lee Packham
2001-12-19 16:01   ` Jan Niehusmann
2001-12-19 16:18     ` Brendan Pike
2001-12-19 16:28       ` Oleg Artamonov
2001-12-19 16:44       ` Vojtech Pavlik
2001-12-19 16:59     ` Dmitry Pogosyan
     [not found]   ` <Pine.LNX.4.33.0112191101230.4575-100000@coffee.psychology.mcmaster.ca>
2001-12-19 16:37     ` Thomas Deselaers
2001-12-19 17:34   ` Mike Dresser
2001-12-19 15:55 ` Oleg Artamonov
2001-12-19 16:05   ` Thomas Deselaers [this message]
2001-12-19 16:15     ` Oleg Artamonov
2001-12-19 16:32       ` Thomas Deselaers
2001-12-19 16:38 ` Holger Lubitz
2001-12-22  8:21 ` Adam Keys
2001-12-22  8:56   ` Alan Cox
2001-12-22 10:10     ` Adam Keys
     [not found]       ` <01122215090500.01870@manta>
2001-12-22 13:23         ` Thomas Deselaers
2001-12-20 13:12 Brendan Pike
2001-12-20 17:10 Brendan Pike
2001-12-20 17:22 ` Ryan Cumming
2001-12-20 17:41 ` Sebastian Dröge
2001-12-20 19:25 Brendan Pike
     [not found] <Pine.LNX.4.33.0112201307120.9437-100000@coffee.psychology.mcmaster.ca>
2001-12-20 19:33 ` Brendan Pike
2001-12-22 18:20 Jim Radford
2001-12-22 21:36 ` Craig Knox
2001-12-23  8:11 ` Adam Keys
2001-12-23 17:55 Wayne Whitney
2001-12-23 18:37 ` Mark Hahn

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20011219160529.GA3930@leukertje.hitnet.rwth-aachen.de \
    --to=thomas@deselaers.de \
    --cc=linux-kernel@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®