From: Linux Kernel Mailing List <kernel@iggy.triode.net.au>
To: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: linux-kernel@vger.kernel.org
Subject: Re: ALI 15X3 DMA Freeze
Date: Sun, 10 Feb 2002 15:42:09 +1100 [thread overview]
Message-ID: <20020210154209.A15150@iggy.triode.net.au> (raw)
In-Reply-To: <20020210124207.C5191@iggy.triode.net.au> <E16Zjlb-0000Bh-00@the-village.bc.nu>
In-Reply-To: <E16Zjlb-0000Bh-00@the-village.bc.nu>; from alan@lxorguk.ukuu.org.uk on Sun, Feb 10, 2002 at 02:30:59AM +0000
I've picked up ide.2.4.17.02072002.patch from www.linux-ide.org
and compiled it with 2.4.17. I presume that this was the patch
you were referring to?
With Andre's IDE patch and 2.4.17, my machine locked up when
compiling 2.4.17 with both the DMA on and the DMA off.
With patch-2.4.18-pre9, the machine only locked up when
DMA was set on, with DMA off, I could recompile the kernel
as many times as I wanted.
Following are kernel messages from the kernel boot with
Andre's IDE patch.
Feb 10 15:25:10 solaris kernel: Calibrating delay loop... 3158.83 BogoMIPS
Feb 10 15:25:10 solaris kernel: PCI: Using IRQ router ALI [10b9/1533] at 00:07.0
Feb 10 15:25:10 solaris kernel: ALI15X3: IDE controller on PCI bus 00 dev 20
Feb 10 15:25:10 solaris kernel: ALI15X3: chipset revision 196
Feb 10 15:25:10 solaris kernel: ALI15X3: not 100%% native mode: will probe irqs later
Feb 10 15:25:10 solaris kernel: ALI15X3: ATA-66/100 forced bit set (WARNING)!!
Feb 10 15:25:10 solaris kernel: ALI15X3: simplex device: DMA disabled
Feb 10 15:25:10 solaris kernel: ide0: ALI15X3 Bus-Master DMA disabled (BIOS)
Feb 10 15:25:10 solaris kernel: ALI15X3: simplex device: DMA disabled
Feb 10 15:25:10 solaris kernel: ide1: ALI15X3 Bus-Master DMA disabled (BIOS)
Feb 10 15:25:11 solaris random: Initializing random number generator: succeeded
Feb 10 15:25:10 solaris kernel: ide_setup: ide0=ata66
Feb 10 15:25:10 solaris kernel: Uniform Multi-Platform E-IDE driver Revision: 6.31
Feb 10 15:25:10 solaris kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Feb 10 15:25:10 solaris kernel: ALI15X3: IDE controller on PCI bus 00 dev 20
Feb 10 15:25:10 solaris kernel: ide0: ALI15X3 Bus-Master DMA disabled (BIOS)
Feb 10 15:25:10 solaris kernel: ide1: ALI15X3 Bus-Master DMA disabled (BIOS)
Feb 10 15:25:10 solaris kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Feb 10 15:25:10 solaris kernel: ide1 at 0x170-0x177,0x376 on irq 15
Please let me know what to try to test next.
Regards. Paul
On Sun, Feb 10, 2002 at 02:30:59AM +0000, Alan Cox wrote:
> > I'm using kernel 2.4.18-pre9, which has a problem when I switch DMA on
> > the IDE hard drive. With DMA enabled, I cannot complete a kernel
> > compile without the machine locking up. The motherboard is an
>
> Start by picking up the ide updates either from the -ac kernel or from
> Andre's web site.
next prev parent reply other threads:[~2002-02-10 4:43 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-02-10 1:42 Linux Kernel Mailing List
2002-02-10 2:30 ` Alan Cox
2002-02-10 4:42 ` Linux Kernel Mailing List [this message]
2002-02-10 15:15 ` Alan Cox
2002-02-10 21:59 ` Linux Kernel Mailing List
[not found] ` <Pine.LNX.4.33.0202101817330.31698-100000@coffee.psychology.mcmaster.ca>
2002-02-10 23:28 ` Linux Kernel Mailing List
2002-02-11 0:30 ` Linux Kernel Mailing List
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20020210154209.A15150@iggy.triode.net.au \
--to=kernel@iggy.triode.net.au \
--cc=alan@lxorguk.ukuu.org.uk \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®