From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id ; Sun, 10 Feb 2002 19:31:16 -0500 Received: (majordomo@vger.kernel.org) by vger.kernel.org id ; Sun, 10 Feb 2002 19:31:06 -0500 Received: from iggy.triode.net.au ([203.63.235.1]:4488 "EHLO iggy.triode.net.au") by vger.kernel.org with ESMTP id ; Sun, 10 Feb 2002 19:30:54 -0500 Date: Mon, 11 Feb 2002 11:30:17 +1100 From: Linux Kernel Mailing List To: Mark Hahn Cc: linux-kernel@vger.kernel.org Subject: Re: ALI 15X3 DMA Freeze Message-ID: <20020211113017.A4461@iggy.triode.net.au> In-Reply-To: <20020211085956.A23445@iggy.triode.net.au> Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Disposition: inline User-Agent: Mutt/1.2.5.1i In-Reply-To: ; from hahn@physics.mcmaster.ca on Sun, Feb 10, 2002 at 06:17:56PM -0500 Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org Now I have turned off "PNP OS" and fiddled a little with the boot options. Same basic problem remains, the machine compiles the kernel fine with DMA off but freezes when compiling the kernel with DMA on. Here are the new boot messages: Regards. Paul Kernel command line: auto BOOT_IMAGE=2.4.17.9 ro root=301 BOOT_FILE=/boot/bzImage-2.4.17.9 idebus=66 ide0=ata66 pci=biosirq ide_setup: idebus=66 ide_setup: ide0=ata66 PCI: PCI BIOS revision 2.10 entry at 0xf1170, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware Unknown bridge resource 0: assuming transparent PCI: Using IRQ router ALI [10b9/1533] at 00:07.0 Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 66MHz system bus speed for PIO modes ALI15X3: IDE controller on PCI bus 00 dev 20 PCI: No IRQ known for interrupt pin A of device 00:04.0. ALI15X3: chipset revision 196 ALI15X3: not 100% native mode: will probe irqs later ALI15X3: ATA-66/100 forced bit set (WARNING)!! ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:pio, hdd:DMA hda: IC35L040AVER07-0, ATA DISK drive hdb: CDU5211, ATAPI CD/DVD-ROM drive hdd: IOMEGA ZIP 250 ATAPI, ATAPI FLOPPY drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: 80418240 sectors (41174 MB) w/1916KiB Cache, CHS=5005/255/63 hdb: ATAPI 52X CD-ROM drive, 120kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 Partition check: hda: hda1 hda2 On Sun, Feb 10, 2002 at 06:17:56PM -0500, Mark Hahn wrote: > > PCI: No IRQ known for interrupt pin A of device 00:04.0. > > are you sure you don't have the bios set for "PNP OS"?