From: Rudmer van Dijk <rudmer@legolas.dynup.net>
To: Alan Cox <alan@redhat.com>, Andre Hedrick <andre@linux-ide.org>
Cc: linux-kernel@vger.kernel.org
Subject: ide-scsi on ide-2.4.20-pre4-ac2
Date: Thu, 29 Aug 2002 00:36:49 +0200 [thread overview]
Message-ID: <20020828223226Z319086-685+38604@vger.kernel.org> (raw)
Hi Alan, Andre,
I want to confirm that using ide-scsi with the latest ide-patch from Andre
now works!! just burned a cd and then read the whole disk back to hd without
any errors!!
Rudmer
some system info:
messages on loading scsi-modules:
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: IOMEGA Model: ZIP 100 Rev: 23.D
Type: Direct-Access ANSI SCSI revision: 00
Vendor: HL-DT-ST Model: CD-RW GCE-8240B Rev: 1.06
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 24x/40x writer cd/rw xa/form2 cdda tray
output of /proc/ide/sis:
SiS 5513 Ultra 100 chipset
--------------- Primary Channel ---------------- Secondary Channel
-------------
Channel Status: On On
Operation Mode: Compatible Compatible
Cable Type: 80 pins 40 pins
Prefetch Count: 512 512
Drive 0: Postwrite Enabled Postwrite Disabled
Prefetch Enabled Prefetch Disabled
UDMA Enabled UDMA Disabled
UDMA Cycle Time 2 CLK UDMA Cycle Time Reserved
Data Active Time 3 PCICLK Data Active Time 3 PCICLK
Data Recovery Time 1 PCICLK Data Recovery Time 1 PCICLK
Drive 1: Postwrite Disabled Postwrite Disabled
Prefetch Disabled Prefetch Disabled
UDMA Disabled UDMA Disabled
UDMA Cycle Time Reserved UDMA Cycle Time Reserved
Data Active Time 8 PCICLK Data Active Time 8 PCICLK
Data Recovery Time 12 PCICLK Data Recovery Time 12 PCICLK
output of lspci -vvv:
00:00.0 Host bridge: Silicon Integrated Systems [SiS]: Unknown device 0735
(rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=32M]
Capabilities: [c0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x1
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] 5591/5592 AGP (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: cee00000-cfefffff
Prefetchable memory behind bridge: ccc00000-cecfffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0)
(prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller
(A,B step)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Region 4: I/O ports at ff00 [size=16]
00:0b.0 Ethernet controller: Winbond Electronics Corp W89C940
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at dc00 [size=32]
00:0f.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI128
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at d800 [size=64]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 Ethernet controller: Winbond Electronics Corp W89C940
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d400 [size=32]
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP (rev
01) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G200 AGP
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at cd000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at cfefc000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at cf000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at cfee0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
output of scripts/ver_linux:
Linux gandalf 2.4.20-pre4-ac2 #1 Wed Aug 28 15:00:43 CEST 2002 i686 unknown
Gnu C 2.95.3
Gnu make 3.79.1
util-linux 2.11q
mount 2.11q
modutils 2.4.16
e2fsprogs 1.27
Linux C Library 2.2.5
Dynamic linker (ldd) 2.2.5
Procps 2.0.7
Net-tools 1.60
Kbd 1.06
Sh-utils 2.0
Modules Loaded sg nls_iso8859-1 ide-scsi sr_mod scsi_mod cdrom isofs
zlib_inflate
reply other threads:[~2002-08-28 22:32 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20020828223226Z319086-685+38604@vger.kernel.org \
--to=rudmer@legolas.dynup.net \
--cc=alan@redhat.com \
--cc=andre@linux-ide.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®