From: axel@hh59.org
To: linux-kernel@vger.kernel.org
Cc: martin@dalecki.de, akpm@zip.com.au
Subject: 2.5.36: PCI: Unable to reserve I/O region
Date: Wed, 18 Sep 2002 18:25:23 +0200 [thread overview]
Message-ID: <20020918162523.GA204@prester.hh59.org> (raw)
[-- Attachment #1: Type: text/plain, Size: 4592 bytes --]
Hi,
just booted 2.5.36-mm1. The following part from dmesg appeared a little
strange or rather wrong to me. The systems runs fine as far as I can see.
ide1 at 0x170-0x177,0x376 on irq 15
ICH: IDE controller at PCI slot 00:1f.1
PCI: Unable to reserve I/O region #5:10@f000 for device 00:1f.1
ICH: not 100% native mode: will probe irqs later
ICH: port 0x01f0 already claimed by ide0
ICH: port 0x0170 already claimed by ide1
ICH: neither IDE port enabled (BIOS)
Are these messages bad?
Best regards,
Axel
Linux prester 2.5.36-mm1 #0 Wed Sep 18 17:38:19 CEST 2002 i686 unknown
Gnu C gcc (GCC) 3.2.1 20020915 (prerelease) Copyright (C)
2002
Free Software Foundation, Inc. This is free software; see the source for
copying conditions. There is NO warranty; not even for MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.
Gnu make 3.79.1
util-linux 2.11r
mount 2.11r
modutils 2.4.19
e2fsprogs 1.27
PPP 2.4.1
Linux C Library 2.2.5
Dynamic linker (ldd) 2.2.5
Procps 2.0.8
Net-tools 1.60
Kbd 1.06
Sh-utils 2.0
Modules Loaded 8250 core rtc nls_iso8859-1 nls_cp437 minix
00:00.0 Host bridge: Intel Corp. 82810 GMCH [Graphics Memory Controller Hub]
(rev 03)
Subsystem: Intel Corp. 82810 GMCH [Graphics Memory Controller Hub]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
00:01.0 VGA compatible controller: Intel Corp. 82810 CGC [Chipset Graphics
Controller] (rev 03) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at d4000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 02) (prog-if 00
[Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 02) (prog-if 80
[Master])
Subsystem: Intel Corp. 82801AA IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at f000 [size=16]
00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corp. 82801AA USB
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at d000 [size=32]
00:1f.5 Multimedia audio controller: Intel Corp. 82801AA AC'97 Audio (rev
02)
Subsystem: Analog Devices: Unknown device 5348
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at dc00 [size=64]
[-- Attachment #2: dmesg.out.bz2 --]
[-- Type: application/octet-stream, Size: 3792 bytes --]
[-- Attachment #3: config-2.5.36.bz2 --]
[-- Type: application/octet-stream, Size: 4564 bytes --]
next reply other threads:[~2002-09-18 16:20 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-09-18 16:25 axel [this message]
2002-09-18 16:32 ` Andrew Morton
2002-09-18 16:42 ` Alan Cox
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20020918162523.GA204@prester.hh59.org \
--to=axel@hh59.org \
--cc=akpm@zip.com.au \
--cc=linux-kernel@vger.kernel.org \
--cc=martin@dalecki.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®