From: Luc Saillard <luc.saillard@fr.alcove.com>
To: Jens Axboe <axboe@suse.de>
Cc: linux-kernel@vger.kernel.org
Subject: Re: oops when using ide-cd with 2.5.45 and cdrecord
Date: Sun, 3 Nov 2002 01:23:46 +0100 [thread overview]
Message-ID: <20021103002346.GA25842@cedar.alcove-fr> (raw)
In-Reply-To: <20021102213448.GA3612@suse.de>
On Sat, Nov 02, 2002 at 10:34:48PM +0100, Jens Axboe wrote:
> On Sat, Nov 02 2002, Luc Saillard wrote:
> > Hi,
> > I'm a using the last cdrecord version (1.11a39) when this oops occurs.
> > I can't sync my disks with alt-sys-request because we are in interrupt
> > :(
>
> How are you invoking cdrecord? Using ide-scsi?
>
Like this:
./cdrecord dev=/dev/hdc fs=32m speed=24 -v -eject driveropts=burnfree dump.001
Cdrecord 1.11a39 (i686-pc-linux-gnu) Copyright (C) 1995-2002 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: '/dev/hdc'
devname: '/dev/hdc'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
Using libscg version 'schily-0.7'
Driveropts: 'burnfree'
atapi: 1
Device type : Removable CD-ROM
Version : 2
Response Format: 2
Capabilities : SYNC
Vendor_info : 'YAMAHA '
Identifikation : 'CRW-F1E '
Revision : '1.0c'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE AUDIOMASTER FORCESPEED DISKTATTOO
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R96R
Drive buf size : 7469952 = 7294 KB
FIFO size : 33554432 = 32768 KB
Track 01: data 689 MB
Total size: 791 MB (78:26.69) = 353002 sectors
Lout start: 792 MB (78:28/52) = 353002 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Is not unrestricted
Is not erasable
Disk sub type: Medium Type B, low Beta category (B-) (4)
ATIP start of lead in: -12369 (97:17/06)
ATIP start of lead out: 359849 (79:59/74)
I've do many simulations with -dummy option, without problem, when i try to burn
for real the cd, i have the oops. Between each test (or burning session), i
eject the cd. For this test, i don't pass hdc=ide-scsi to the kernel
commandline option.
Ok here informations about my system:
/mnt/linux/srcs/linux/linux-2.5/linux-2.5.45>sh ./scripts/ver_linux
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux darkland 2.5.45 #6 Sat Nov 2 19:49:59 CET 2002 i686 Celeron (Mendocino) GenuineIntel GNU/Linux
Gnu C 2.95.4
Gnu make 3.80
util-linux 2.11u
mount 2.11u
modutils 2.4.19
e2fsprogs 1.30-WIP
./scripts/ver_linux: 37: fsck.jfs: not found
./scripts/ver_linux: 40: reiserfsck: not found
./scripts/ver_linux: 43: xfs_db: not found
./scripts/ver_linux: 46: cardmgr: not found
PPP 2.4.1
./scripts/ver_linux: 52: isdnctrl: not found
Linux C Library 2.3.1
Dynamic linker (ldd) 2.3.1
Procps 3.0.3
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 4.5.2
Modules Loaded nfsd lockd sunrpc exportfs snd-seq-oss snd-seq-midi-event snd-seq snd-pcm-oss snd-mixer-oss snd-dummy snd-interwave snd-gus-lib snd-rawmidi snd-seq-device snd-cs4231-lib snd-pcm snd-timer snd rtc ipt_TOS ipt_MASQUERADE ipt_limit ipt_REDIRECT ipt_multiport ipt_LOG ipt_REJECT ipt_state iptable_mangle hid ip_nat_irc ip_nat_ftp iptable_nat ip_conntrack_irc ip_conntrack_ftp ip_conntrack iptable_filter ip_tables uhci-hcd usbmouse usbcore
darkland:~# lspci -vvv
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: c0000000-cfffffff
Prefetchable memory behind bridge: d8000000-dfffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at f000 [size=16]
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 7
Region 4: I/O ports at e000 [size=32]
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:09.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at e400 [size=128]
Region 1: Memory at e1000000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at e800 [size=32]
00:0d.0 SCSI storage controller: Adaptec AHA-2940U/UW/D / AIC-7881U
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at ec00 [disabled] [size=256]
Region 1: Memory at e1001000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
01:00.0 VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 4 / Voodoo 5 (rev 01) (prog-if 00 [VGA])
Subsystem: 3Dfx Interactive, Inc.: Unknown device 0004
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 3
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=128M]
Region 1: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 2: I/O ports at d000 [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [54] AGP version 2.0
Status: RQ=15 SBA+ 64bit+ FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
darkland:~# cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 6
model name : Celeron (Mendocino)
stepping : 0
cpu MHz : 342.495
cache size : 128 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr
bogomips : 675.84
darkland:~# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: QUANTUM Model: XP34550S Rev: LXQ1
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: QUANTUM Model: XP34550S Rev: LXQ1
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: MATSHITA Model: CD-R CW-7502 Rev: 4.17
Type: CD-ROM ANSI SCSI revision: 02
darkland:~# cat /proc/modules
nfsd 73328 2 (autoclean)
lockd 48848 1 (autoclean) [nfsd]
sunrpc 80344 1 (autoclean) [nfsd lockd]
exportfs 3320 0 (autoclean) [nfsd]
snd-seq-oss 22144 0 (unused)
snd-seq-midi-event 3048 0 [snd-seq-oss]
snd-seq 32912 2 [snd-seq-oss snd-seq-midi-event]
snd-pcm-oss 36548 0 (unused)
snd-mixer-oss 10264 1 [snd-pcm-oss]
snd-dummy 4028 1
snd-interwave 6644 0 (unused)
snd-gus-lib 30532 0 [snd-interwave]
snd-rawmidi 11616 0 [snd-gus-lib]
snd-seq-device 3824 0 [snd-seq-oss snd-seq snd-gus-lib snd-rawmidi]
snd-cs4231-lib 13988 0 [snd-interwave]
snd-pcm 53568 0 [snd-pcm-oss snd-dummy snd-gus-lib snd-cs4231-lib]
snd-timer 9400 0 [snd-seq snd-gus-lib snd-cs4231-lib snd-pcm]
snd 23908 0 [snd-seq-oss snd-seq-midi-event snd-seq snd-pcm-oss snd-mixer-oss snd-dummy snd-interwave snd-gus-lib snd-rawmidi snd-seq-device snd-cs4231-lib snd-pcm snd-timer]
rtc 6864 0 (autoclean)
ipt_TOS 1208 12 (autoclean)
ipt_MASQUERADE 1496 1 (autoclean)
ipt_limit 1176 6 (autoclean)
ipt_REDIRECT 920 2 (autoclean)
ipt_multiport 856 3 (autoclean)
ipt_LOG 3416 8 (autoclean)
ipt_REJECT 3128 2 (autoclean)
ipt_state 792 94 (autoclean)
iptable_mangle 2292 1 (autoclean)
hid 17992 0 (unused)
ip_nat_irc 2512 0 (unused)
ip_nat_ftp 3152 0 (unused)
iptable_nat 15704 3 [ipt_MASQUERADE ipt_REDIRECT ip_nat_irc ip_nat_ftp]
ip_conntrack_irc 3184 1
ip_conntrack_ftp 3984 1
ip_conntrack 18400 4 [ipt_MASQUERADE ipt_REDIRECT ipt_state ip_nat_irc ip_nat_ftp iptable_nat ip_conntrack_irc ip_conntrack_ftp]
iptable_filter 1896 1 (autoclean)
ip_tables 10264 13 [ipt_TOS ipt_MASQUERADE ipt_limit ipt_REDIRECT ipt_multiport ipt_LOG ipt_REJECT ipt_state iptable_mangle iptable_nat iptable_filter]
uhci-hcd 22920 0 (unused)
usbmouse 2436 0 (unused)
usbcore 72660 2 [hid uhci-hcd usbmouse]
darkland:/mnt/bigdur/tmp# cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0213-0213 : isapnp read
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
0a79-0a79 : isapnp write
0cf8-0cff : PCI conf1
4000-403f : Intel Corp. 82371AB/EB/MB PIIX4 ACPI
5000-501f : Intel Corp. 82371AB/EB/MB PIIX4 ACPI
d000-dfff : PCI Bus #01
d000-d0ff : 3Dfx Interactive, Inc. Voodoo 4 / Voodoo 5
e000-e01f : Intel Corp. 82371AB/EB/MB PIIX4 USB
e000-e01f : uhci-hcd
e400-e47f : 3Com Corporation 3c905C-TX/TX-M [Tornado]
e400-e47f : 00:09.0
e800-e81f : Realtek Semiconductor Co., Ltd. RTL-8029(AS)
e800-e81f : ne2k-pci
ec00-ecff : Adaptec AHA-2940U/UW/D / AIC-7881U
ec00-ecff : aic7xxx
f000-f00f : Intel Corp. 82371AB/EB/MB PIIX4 IDE
f000-f007 : ide0
f008-f00f : ide1
darkland:/mnt/bigdur/tmp# cat /proc/iomem
00000000-0009ffff : System RAM
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000cc000-000cc7ff : Extension ROM
000cd000-000d35ff : Extension ROM
000f0000-000fffff : System ROM
00100000-13feffff : System RAM
00100000-0025adc3 : Kernel code
0025adc4-002f4723 : Kernel data
13ff0000-13ff2fff : ACPI Non-volatile Storage
13ff3000-13ffffff : ACPI Tables
c0000000-cfffffff : PCI Bus #01
c0000000-c7ffffff : 3Dfx Interactive, Inc. Voodoo 4 / Voodoo 5
d0000000-d7ffffff : Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
d8000000-dfffffff : PCI Bus #01
d8000000-dfffffff : 3Dfx Interactive, Inc. Voodoo 4 / Voodoo 5
e1000000-e100007f : 3Com Corporation 3c905C-TX/TX-M [Tornado]
e1001000-e1001fff : Adaptec AHA-2940U/UW/D / AIC-7881U
e1001000-e1001fff : aic7xxx
ffff0000-ffffffff : reserved
Do you want my kernel config ?
Luc
next prev parent reply other threads:[~2002-11-03 0:17 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-11-02 21:01 Luc Saillard
2002-11-02 21:34 ` Jens Axboe
2002-11-03 0:23 ` Luc Saillard [this message]
2002-11-03 9:40 ` Jens Axboe
2002-11-03 14:42 ` Luc Saillard
2002-11-03 14:56 ` Jens Axboe
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20021103002346.GA25842@cedar.alcove-fr \
--to=luc.saillard@fr.alcove.com \
--cc=axboe@suse.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®