From: Stephan Austermuehle <au@hcsd.de>
To: linux-kernel@vger.kernel.org
Subject: PROBLEM: PCI Device not accessible (resource collisions)
Date: Tue, 26 Nov 2002 14:06:29 +0100 [thread overview]
Message-ID: <20021126130629.GA16298@hcsd.de> (raw)
[-- Attachment #1: Type: text/plain, Size: 10793 bytes --]
Hello,
I cannot load the driver modul aic7xxx for my onboard SCSI controller:
Nov 26 13:52:52 hopper kernel: PCI: Device 04:03.1 not available because of resource collisions
Nov 26 13:52:52 hopper kernel: PCI: Device 04:03.0 not available because of resource collisions
The SCSI controller is included on my Supermicro P4DL6 mainboard equiped
with 2 Intel Xeon processors.
System version information:
Linux hopper 2.4.19-xfs #8 SMP Sat Nov 23 09:47:01 CET 2002 i686 Intel(R) XEON(TM) CPU 1.80GHz GenuineIntel GNU/Linux
Gnu C 2.95.4
Gnu make 3.79.1
util-linux 2.11n
mount 2.11n
modutils 2.4.19
e2fsprogs 1.30-WIP
isdn4k-utils 3.1pre4
Linux C Library 2.3.1
Dynamic linker (ldd) 2.3.1
Procps 2.0.7
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 4.5.2
Modules Loaded nfsd lockd sunrpc serial isa-pnp parport_pc lp parport loop eepro100 ipv6 usb-ohci usbcore
Output of lspci -vvv:
00:00.0 Host bridge: ServerWorks: Unknown device 0012 (rev 13)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.1 Host bridge: ServerWorks: Unknown device 0012
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.2 Host bridge: ServerWorks: Unknown device 0000
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:02.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Rage XL
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), cache line size 10
Interrupt: pin A routed to IRQ 29
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at a800 [size=256]
Region 2: Memory at fe7ff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at fe7c0000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 0d)
Subsystem: Intel Corp. EtherExpress PRO/100 S Server Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 14000ns max), cache line size 10
Interrupt: pin A routed to IRQ 30
Region 0: Memory at fe7fd000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at af00 [size=64]
Region 2: Memory at fe7a0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at fe7e0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:0f.0 ISA bridge: ServerWorks CSB5 South Bridge (rev 93)
Subsystem: Unknown device d915:5538
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
00:0f.1 IDE interface: ServerWorks CSB5 IDE Controller (rev 93) (prog-if 8a [Master SecP PriP])
Subsystem: ServerWorks CSB5 IDE Controller
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at ffa0 [size=16]
00:0f.2 USB Controller: ServerWorks OSB4/CSB5 USB Controller (rev 05) (prog-if 10 [OHCI])
Subsystem: ServerWorks OSB4/CSB5 USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (20000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe7fe000 (32-bit, non-prefetchable) [size=4K]
00:0f.3 Host bridge: ServerWorks: Unknown device 0225
Subsystem: Unknown device d915:5538
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:10.0 Host bridge: ServerWorks: Unknown device 0101 (rev 03)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=4
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
00:10.2 Host bridge: ServerWorks: Unknown device 0101 (rev 03)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=4
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
00:11.0 Host bridge: ServerWorks: Unknown device 0101 (rev 03)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=4
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
00:11.2 Host bridge: ServerWorks: Unknown device 0101 (rev 03)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=4
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
01:03.0 Ethernet controller: BROADCOM Corporation NetXtreme BCM5701 Gigabit Ethernet (rev 15)
Subsystem: BROADCOM Corporation: Unknown device 1644
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), cache line size 10
Interrupt: pin A routed to IRQ 31
Region 0: Memory at fe8f0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at fe8e0000 [disabled] [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 6d73cb20ae86b01c Data: 9201
03:02.0 SCSI storage controller: ICP Vortex Computersysteme GmbH GDT 6128RS/6528RS/6628RS
Subsystem: ICP Vortex Computersysteme GmbH GDT 6128RS/6528RS/6628RS
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 10
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fc5fc000 (32-bit, prefetchable) [size=16K]
Expansion ROM at feaf0000 [disabled] [size=32K]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:03.0 SCSI storage controller: Adaptec AIC-7899P U160/m (rev 01)
Subsystem: Super Micro Computer Inc: Unknown device 9005
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 16
BIST result: 00
Region 0: I/O ports at <unassigned> [disabled]
Region 1: Memory at <unassigned> (64-bit, non-prefetchable) [disabled]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:03.1 SCSI storage controller: Adaptec AIC-7899P U160/m (rev 01)
Subsystem: Super Micro Computer Inc: Unknown device 9005
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 17
BIST result: 00
Region 0: I/O ports at <unassigned> [disabled]
Region 1: Memory at <unassigned> (64-bit, non-prefetchable) [disabled]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
There's a another SCSI controller in the system:
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ICP Model: Host Drive #00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: ICP Model: Host Drive #01 Rev:
Type: Direct-Access ANSI SCSI revision: 02
The problem is present in 2.4.18-xfs-1.1 as well.
What can I do to get the aic7xxx driver running so I can do backups of
my system?
Please let me know if I forgot to include any information.
Thanks for your help,
Stephan
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
reply other threads:[~2002-11-26 12:59 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20021126130629.GA16298@hcsd.de \
--to=au@hcsd.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®