From: Gregoire Favre <greg@ulima.unil.ch>
To: linux-kernel@vger.kernel.org
Subject: 2.5.54 problem with IDE ICH4 and aic7xxx
Date: Sun, 5 Jan 2003 17:54:41 +0100 [thread overview]
Message-ID: <20030105165441.GA8215@ulima.unil.ch> (raw)
Hello,
I have put whole dmesg, .config, lspci, ver_linux, /proc/interrupts,
/proc/ide/piix, /proc/partitions, /proc/scsi/aic7xxx/0,
/proc/scsi/aic7xxx/1, /proc/scsi/scsi under
http://ulima.unil.ch/greg/linux/2.5.54/
One could also find patch-2.5.45-mouse that I used such that my mouse
work (wireless one, reverse patch), and other patch I have applied are
the ones from linux-dvb :
cvs -d :pserver:anonymous@linuxtv.org:/cvs/linuxtv co dvb-kernel
But I get the same result without those patches ;-)
I got an MSI Max2-BLR which has an onboard IDE Raid that isn't acticated
in the BIOS (if I turn it on, it doesn't change anything at all...
Under 2.4.20 it boots perfectly...
What I found really strange is the time my IDE take to boot. More than
five minutes for thoses lines :
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: IC35L120AVVA07-0, ATA DISK drive
hda: bad special flag: 0x03
hda: tagged command queueing enabled, command queue depth 8
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SONY DVD RW DRU-500A, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 250 ATAPI, ATAPI FLOPPY drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=239340/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 >
hdc: ATAPI 16X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
ide-floppy driver 0.99.newide
hdd: 244766kB, 489532 blocks, 512 sector size
hdd: 244736kB, 239/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
hdd: The disk reports a capacity of 250640384 bytes, but the drive only handles 250
609664
hdd: The disk reports a capacity of 250640384 bytes, but the drive only handles 250
609664
/dev/ide/host0/bus1/target1/lun0: unknown partition table
/dev/ide/host0/bus1/target1/lun0: unknown partition table
Which is imediatly followed by:
aic7xxx: PCI Device 3:3:0 failed memory mapped test. Using PIO.
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.25
<Adaptec 29160B Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
(scsi1:A:1:0): refuses WIDE negotiation. Using 8bit transfers
(scsi0:A:15): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit)
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled. Depth 253
Vendor: SEAGATE Model: ST336706LW Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:15:0: Tagged Queuing enabled. Depth 253
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.25
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
(scsi1:A:1): 10.000MB/s transfers (10.000MHz, offset 15)
(scsi1:A:2): 10.000MB/s transfers (10.000MHz, offset 8)
(scsi1:A:3): 10.000MB/s transfers (10.000MHz, offset 8)
Vendor: TOSHIBA Model: DVD-ROM SD-M1201 Rev: 1R04
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PLEXTOR Model: CD-R PX-R820T Rev: 1.08
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PLEXTOR Model: CD-R PX-R820T Rev: 1.08
Type: CD-ROM ANSI SCSI revision: 02
SCSI device sda: drive cache: write through
SCSI device sda: 17850000 512-byte hdwr sectors (9139 MB)
/dev/scsi/host0/bus0/target0/lun0: p1 p2
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: drive cache: write back
SCSI device sdb: 71687370 512-byte hdwr sectors (36704 MB)
/dev/scsi/host0/bus0/target15/lun0: p1 p2
Attached scsi disk sdb at scsi0, channel 0, id 15, lun 0
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 1, lun 0
sr1: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr1 at scsi1, channel 0, id 2, lun 0
sr2: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr2 at scsi1, channel 0, id 3, lun 0
device class 'input': registering
Should I do something different?
Thank you very much and have a great day ;-)
Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:greg@ulima.unil.ch
next reply other threads:[~2003-01-05 16:46 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-01-05 16:54 Gregoire Favre [this message]
2003-01-05 17:35 ` Justin T. Gibbs
2003-01-05 17:42 ` Gregoire Favre
2003-01-05 18:49 ` Alan Cox
2003-01-05 19:41 ` Gregoire Favre
2003-01-05 20:37 ` Alan Cox
2003-01-05 18:52 ` Gregoire Favre
2003-01-09 22:56 ` 2.5.54 problem with IDE ICH4 and aic7xxx -> fixed in 2.5.55 Gregoire Favre
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20030105165441.GA8215@ulima.unil.ch \
--to=greg@ulima.unil.ch \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®