From: Daniel Podlejski <underley@underley.eu.org>
To: linux-kernel@vger.kernel.org
Subject: AIC7xxx problem
Date: Sat, 31 May 2003 18:59:45 +0200 [thread overview]
Message-ID: <20030531165945.GA5561@witch.underley.eu.org> (raw)
I have Adaptec SCSI controler, which with 2.4.20-ac2 boots ok:
====================================================================
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
<Adaptec 2940 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=15, 32/253 SCBs
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 63, 16bit)
Vendor: IBM Model: DPSS-318350N Rev: S96H
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:0:0: Tagged Queuing enabled. Depth 16
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 35843670 512-byte hdwr sectors (18352 MB)
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
====================================================================
but performance is poor - periodically all disk operations
stops for few seconds. I try to use newer drivers, but without
positiver results. Here is log from boot with verbose option:
====================================================================
[...]
SCSI subsystem driver Revision: 1.00
ahc_pci:2:10:0: Reading SEEPROM...done.
ahc_pci:2:10:0: Manual LVD Termination
ahc_pci:2:10:0: BIOS eeprom is present
ahc_pci:2:10:0: Secondary High byte termination Enabled
ahc_pci:2:10:0: Secondary Low byte termination Enabled
ahc_pci:2:10:0: Primary Low Byte termination Enabled
ahc_pci:2:10:0: Primary High Byte termination Enabled
ahc_pci:2:10:0: Downloading Sequencer Program... 423 instructions downloaded
ahc_pci:2:10:0: Features 0x56f6, Bugs 0x6, Flags 0x20485500
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.35
<Adaptec 2940 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=15, 32/253 SCBs
(scsi0:A:0): 980KB/s transfers (0.980MHz, offset 255)
scsi0: target 0 using 8bit transfers
(scsi0:A:0): 3.300MB/s transfers
scsi0: target 0 using asynchronous transfers
(scsi0:A:1): 980KB/s transfers (0.980MHz, offset 255)
scsi0: target 1 using 8bit transfers
(scsi0:A:1): 3.300MB/s transfers
scsi0: target 1 using asynchronous transfers
[...]
(scsi0:A:14): 980KB/s transfers (0.980MHz, offset 255)
scsi0: target 14 using 8bit transfers
(scsi0:A:14): 3.300MB/s transfers
scsi0: target 14 using asynchronous transfers
scsi0: target 15 using 8bit transfers
scsi0: target 15 using asynchronous transfers
scsi0: target 0 using 8bit transfers
scsi0: target 0 using asynchronous transfers
scsi0: target 1 using 8bit transfers
scsi0: target 1 using asynchronous transfers
[...]
scsi0: target 12 using 8bit transfers
scsi0: target 12 using asynchronous transfers
scsi0: target 13 using 8bit transfers
scsi0: target 13 using asynchronous transfers
scsi0:0:0:0: Attempting to queue an ABORT message
CDB: 0x12 0x0 0x0 0x0 0xff 0x0
ahc_intr: HOST_MSG_LOOP bad phase 0x0
scsi0: At time of recovery, card was paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi0: Dumping Card State while idle, at SEQADDR 0x45
Card was paused
ACCUM = 0xa0, SINDEX = 0x61, DINDEX = 0xe4, ARG_2 = 0x1
HCNT = 0x0 SCBPTR = 0x0
SCSISIGI[0x0] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x1]:(P_BUSFREE)
SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI) SBLKCTL[0xa]:(SELWIDE|SELBUSB)
SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE) SEQ_FLAGS[0x40]:(NO_CDB_SENT)
SSTAT0[0x0] SSTAT1[0x0] SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8]:(ENSWRAP)
SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO) SXFRCTL0[0x88]:(SPIOEN|DFON)
DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
STACK: 0x3 0xe3 0x0 0x0
SCB count = 5
Kernel NEXTQSCB = 3
Card NEXTQSCB = 4
QINFIFO entries: 4
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 3 Sequencer SCB Info:
0 SCB_CONTROL[0x50]:(MK_MESSAGE|DISCENB) SCB_SCSIID[0xf]:(OID)
SCB_LUN[0x0] SCB_TAG[0xff]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
16 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
17 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
18 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
19 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
20 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
21 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
22 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
23 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
24 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
25 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
26 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
27 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
28 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
29 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
30 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
31 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
Pending list:
4 SCB_CONTROL[0x40]:(DISCENB) SCB_SCSIID[0xf]:(OID) SCB_LUN[0x0]
Kernel Free SCB list: 2 1 0
Untagged Q(0): 4
DevQ(0:0:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi0:0:0:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 0x2002
scsi0: target 14 using 8bit transfers
scsi0: target 14 using asynchronous transfers
====================================================================
Any ideas to fix ?
--
Daniel Podlejski <underley@underley.eu.org>
... 'Cause yesterday's got nothin' for me
Old pictures that I'll always see ...
next reply other threads:[~2003-05-31 16:46 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-05-31 16:59 Daniel Podlejski [this message]
2003-06-01 8:19 ` Daniel Podlejski
2003-06-01 8:36 ` Willy Tarreau
2003-06-01 20:34 ` Justin T. Gibbs
2003-06-01 20:45 ` Willy Tarreau
2003-06-01 20:56 ` Zwane Mwaikambo
2003-06-01 21:37 ` Justin T. Gibbs
2003-06-01 21:38 ` Zwane Mwaikambo
-- strict thread matches above, loose matches on Subject: below --
2002-11-05 22:34 aic7xxx problem Emmanuel Fuste
2002-11-06 1:24 ` Philippe Troin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20030531165945.GA5561@witch.underley.eu.org \
--to=underley@underley.eu.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®