From: Eivind Tagseth <eivindt@multinet.no>
To: linux-kernel@vger.kernel.org
Subject: Re: Problems with PCMCIA Compact Flash adapter in 2.5.72
Date: Tue, 24 Jun 2003 10:50:16 +0200 [thread overview]
Message-ID: <20030624085016.GA1989@tagseth-trd.consultit.no> (raw)
In-Reply-To: <20030623102941.D23411@flint.arm.linux.org.uk>
* Russell King <rmk@arm.linux.org.uk> [030623 11:32]:
> On Sun, Jun 22, 2003 at 09:16:27PM +0200, Eivind Tagseth wrote:
> > However, removing the card causes a kernel panic, and everything completely
> > freezes. This also happened with 2.5.69, so it's not caused by a recent
> > change.
>
> ide-cs currently calls ide_unregister from interrupt context, which is
> a big nono. Can you try the following patch please (which is completely
> untested)?
Ok, I tried it (with 2.5.73), with slightly better success. I still
get oopses, but the system doesn't hang completely anymore. But the pcmcia
system (and probably more) is unstable afterwards. There are oopses
when shutting down as well...
Console output when inserting the card:
hdc: SanDisk SDCFB-32, CFA DISK drive
ide1 at 0x140-0x147,0x14e on irq 9
hdc: max request size: 128KiB
hdc: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: task_no_data_intr: error=0x04 { DriveStatusError }
hdc: 62720 sectors (32 MB) w/1KiB Cache, CHS=490/4/32
/dev/ide/host1/bus0/target0/lun0: p1
/dev/ide/host1/bus0/target0/lun0: p1
devfs_mk_bdev: could not append to parent for ide/host1/bus0/target0/lun0/part1
kobject_register failed for hdc1 (-17)
Call Trace:
[<c0213560>] kobject_register+0x50/0x60
[<c0186ff7>] register_disk+0x147/0x180
[<c0245e20>] add_disk+0x50/0x60
[<c0245da0>] exact_match+0x0/0x10
[<c0245db0>] exact_lock+0x0/0x20
[<c0264789>] idedisk_attach+0x129/0x1b0
[<c02606af>] ata_attach+0x9f/0x1c0
[<c0259a23>] ideprobe_init+0xe3/0xff
[<c025ebb3>] ide_probe_module+0x13/0x20
[<c025f7ff>] ide_register_hw+0x15f/0x190
[<d0aa3246>] idecs_register+0x66/0x80 [ide_cs]
[<d0a912a5>] CardServices+0x215/0x362 [pcmcia_core]
[<d0aa3798>] ide_config+0x538/0x8a0 [ide_cs]
[<d0a890bc>] set_cis_map+0x3c/0x120 [pcmcia_core]
[<d0a892cc>] read_cis_mem+0x12c/0x1a0 [pcmcia_core]
[<d0a89596>] read_cis_cache+0xe6/0x170 [pcmcia_core]
[<d0a89f1b>] pcmcia_get_tuple_data+0x9b/0xa0 [pcmcia_core]
[<d0a8b25f>] pcmcia_parse_tuple+0x10f/0x180 [pcmcia_core]
[<d0a8b373>] read_tuple+0xa3/0xb0 [pcmcia_core]
[<d0a577c3>] yenta_set_mem_map+0x1c3/0x220 [yenta_socket]
[<c0119105>] __ioremap+0xe5/0x120
[<d0a89e30>] pcmcia_get_next_tuple+0x240/0x290 [pcmcia_core]
[<d0a89955>] pcmcia_get_first_tuple+0xb5/0x160 [pcmcia_core]
[<d0a577c3>] yenta_set_mem_map+0x1c3/0x220 [yenta_socket]
[<d0a577c3>] yenta_set_mem_map+0x1c3/0x220 [yenta_socket]
[<d0a890bc>] set_cis_map+0x3c/0x120 [pcmcia_core]
[<d0a892cc>] read_cis_mem+0x12c/0x1a0 [pcmcia_core]
[<d0a89596>] read_cis_cache+0xe6/0x170 [pcmcia_core]
[<d0a89f1b>] pcmcia_get_tuple_data+0x9b/0xa0 [pcmcia_core]
[<d0a8b25f>] pcmcia_parse_tuple+0x10f/0x180 [pcmcia_core]
[<d0a8b373>] read_tuple+0xa3/0xb0 [pcmcia_core]
[<d0a577c3>] yenta_set_mem_map+0x1c3/0x220 [yenta_socket]
[<c0119105>] __ioremap+0xe5/0x120
[<d0a89e30>] pcmcia_get_next_tuple+0x240/0x290 [pcmcia_core]
[<d0a89955>] pcmcia_get_first_tuple+0xb5/0x160 [pcmcia_core]
[<d0a89596>] read_cis_cache+0xe6/0x170 [pcmcia_core]
[<d0a89e30>] pcmcia_get_next_tuple+0x240/0x290 [pcmcia_core]
[<d0a8b4b3>] pcmcia_validate_cis+0x133/0x210 [pcmcia_core]
[<c0157662>] __find_get_block+0x92/0xf0
[<c01f1ca1>] create_virtual_node+0x361/0x540
[<c01fdfd3>] pathrelse_and_restore+0x43/0x50
[<d0aa3c88>] ide_event+0x58/0xe0 [ide_cs]
[<d0a8fd03>] pcmcia_register_client+0x213/0x280 [pcmcia_core]
[<d0a577c3>] yenta_set_mem_map+0x1c3/0x220 [yenta_socket]
[<d0a9123e>] CardServices+0x1ae/0x362 [pcmcia_core]
[<d0aa30f3>] +0xf3/0x130 [ide_cs]
[<d0aa4960>] dev_info+0x0/0x20 [ide_cs]
[<d0aa3c30>] ide_event+0x0/0xe0 [ide_cs]
[<d0aa3d65>] +0x1c/0x37 [ide_cs]
[<d0a634bf>] get_pcmcia_driver+0x3f/0x50 [ds]
[<d0aa49a0>] ide_cs_driver+0x0/0x80 [ide_cs]
[<d0a62536>] bind_request+0x186/0x220 [ds]
[<d0aa3d65>] +0x1c/0x37 [ide_cs]
[<d0a63141>] ds_ioctl+0x601/0x700 [ds]
[<c011ae76>] preempt_schedule+0x36/0x50
[<c02de8a7>] unix_dgram_sendmsg+0x377/0x580
[<c013c2e0>] __alloc_pages+0xa0/0x330
[<c028705e>] sock_sendmsg+0x9e/0xd0
[<c0118b6c>] do_page_fault+0x23c/0x456
[<c016f32f>] wake_up_inode+0xf/0x30
[<c0180871>] proc_get_inode+0x161/0x190
[<c013c16e>] buffered_rmqueue+0xce/0x1a0
[<c014486b>] zap_pmd_range+0x4b/0x70
[<c01448db>] unmap_page_range+0x4b/0x90
[<c01449ef>] unmap_vmas+0xcf/0x240
[<c0148815>] unmap_region+0x95/0xe0
[<c0148712>] unmap_vma+0x42/0x80
[<c014876f>] unmap_vma_list+0x1f/0x30
[<c0148b5d>] do_munmap+0x15d/0x1c0
[<c0167050>] sys_ioctl+0x100/0x290
[<c010931b>] syscall_call+0x7/0xb
Module ide_cs cannot be unloaded due to unsafe usage in include/linux/module.h:479
ide-cs: hdc: Vcc = 3.3, Vpp = 0.0
(this also happens without your patch. I reported it earlier for 2.5.72, but
I said that it didn't happen after I rebooted. With 2.5.73 (without your
patch) it happens every time.
The device still works though, even with this not very encouraging message.
Console messages when physically removing the card (I haven't mounted
it or done anything with it since inserting the card):
devfs_remove: ide/host1/bus0/target0/lun0/disc not found, cannot remove
Call Trace:
[<c01b014d>] devfs_remove+0xad/0xb0
[<c0245d91>] blk_unregister_region+0x21/0x30
[<c01876ce>] devfs_remove_disk+0x4e/0x95
[<c0187327>] del_gendisk+0x87/0xe0
[<c02643e8>] idedisk_cleanup+0x48/0x60
[<c025f613>] ide_unregister+0x863/0x890
[<c011ac2b>] schedule+0x1bb/0x3d0
[<c0126629>] schedule_timeout+0x69/0xc0
[<d0aa3b94>] ide_release+0x94/0x130 [ide_cs]
[<d0aa3c7a>] ide_event+0x4a/0xe0 [ide_cs]
[<d0a8e361>] send_event+0x61/0x70 [pcmcia_core]
[<d0a8e3e0>] socket_remove_drivers+0x20/0x50 [pcmcia_core]
[<d0a8e423>] socket_shutdown+0x13/0x60 [pcmcia_core]
[<d0a8e9a3>] pccardd+0x143/0x210 [pcmcia_core]
[<c011ae90>] default_wake_function+0x0/0x30
[<c01091f2>] ret_from_fork+0x6/0x14
[<c011ae90>] default_wake_function+0x0/0x30
[<d0a8e860>] pccardd+0x0/0x210 [pcmcia_core]
[<c01071e5>] kernel_thread_helper+0x5/0x10
There are some weird messages about devices.
This is what it looks like when the card is in:
brw------- 1 eivindt root 22, 1 Jan 1 1970 /dev/ide/host1/bus0/target0/lun0/part1
This is what it looks like when it's been removed:
drwxr-xr-x 1 root root 0 Jan 1 1970 /dev/ide/host1/bus0/target0/
There is not /dev/ide/host1 when the card has not been inserted at all.
Hope this helps, Eivind
prev parent reply other threads:[~2003-06-24 8:36 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-06-20 8:18 Eivind Tagseth
2003-06-20 17:50 ` Bill Davidsen
2003-06-20 20:08 ` Russell King
2003-06-20 20:16 ` Russell King
2003-06-22 11:46 ` Eivind Tagseth
2003-06-22 13:15 ` Russell King
2003-06-22 18:28 ` Eivind Tagseth
2003-06-22 19:16 ` Eivind Tagseth
2003-06-23 9:29 ` Russell King
2003-06-23 11:33 ` Alan Cox
2003-06-24 8:50 ` Eivind Tagseth [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20030624085016.GA1989@tagseth-trd.consultit.no \
--to=eivindt@multinet.no \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®