[2.6.0-test*] Timer interrupts not fired at all? (With a remark to Framebuffers)

mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed

From: Thunder Anklin <thunder@keepsake.ch>
To: linux-kernel@vger.kernel.org
Subject: [2.6.0-test*] Timer interrupts not fired at all? (With a remark to Framebuffers)
Date: Fri, 31 Oct 2003 14:10:19 +0100	[thread overview]
Message-ID: <20031031131019.GA780@dbintra.dmz.lightweight.ods.org> (raw)

[-- Attachment #1: Type: text/plain, Size: 8482 bytes --]

Salut,

I happened to notice that under Linux 2.6.0-test[1-9] timer interrupts
appear not to  be fired at all unless  another interrupt happens. This
has been shown by some weird behaviors:

1. sleeps on boot can take an  infinite amount of time, but if I press
   any key, the booting will continue at once.

2. If I call date on a console  when the PC is idle, each call to date
   will show exactly one second more, even if I waited ten seconds.

3. When I do something like playing ogg streams, the clock runs at its
   usual rate.

I didn't  see any of these problems  on Linux 2.4 or  FreeBSD 4.8, but
FreeBSD  5.* behaves  in a  strange way,  too: the  clock will  run at
double speed.

(Another  probably bad  thing: The  NVidia framebuffer  driver doesn't
appear to work  well for me: if I switch to  more than 800x600@85, the
monitor switches itself  off. Note, however, that 2.4  is working well
at 1024x768@100.)

thunder@dbintra:/tmp$ sudo lspci -vvv
Password:
00:00.0 Host bridge: ALi Corporation M1541 (rev 04)
	Subsystem: ALi Corporation ALI M1541 Aladdin V/V+ AGP System Controller
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 64
	Region 0: Memory at e2000000 (32-bit, non-prefetchable) [size=32M]
	Capabilities: [b0] AGP version 1.0
		Status: RQ=29 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: ALi Corporation M1541 PCI to AGP Controller (rev 04) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
	I/O behind bridge: 0000e000-0000dfff
	Memory behind bridge: e1000000-e1ffffff
	Prefetchable memory behind bridge: e5f00000-e7ffffff
	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-

00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (20000ns max)
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at e0800000 (32-bit, non-prefetchable) [size=4K]

00:03.0 Bridge: ALi Corporation M7101 PMU
	Subsystem: ALi Corporation ALI M7101 Power Management Controller
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:06.0 Multimedia audio controller: ESS Technology ES1969 Solo-1 Audiodrive (rev 01)
	Subsystem: ESS Technology Solo-1 Audio Adapter
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (500ns min, 6000ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: I/O ports at d800 [size=64]
	Region 1: I/O ports at d400 [size=16]
	Region 2: I/O ports at d000 [size=16]
	Region 3: I/O ports at b800 [size=4]
	Region 4: I/O ports at b400 [size=4]
	Capabilities: [c0] Power Management version 1
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV] (rev c3)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort+ >SERR- <PERR-
	Latency: 0

00:09.0 SCSI storage controller: Tekram Technology Co.,Ltd. TRM-S1040 (rev 01)
	Subsystem: Tekram Technology Co.,Ltd. TRM-S1040
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, cache line size 08
	Interrupt: pin A routed to IRQ 12
	Region 0: I/O ports at b000 [size=256]
	Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at <unassigned> [disabled] [size=64K]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
	Subsystem: Realtek Semiconductor Co., Ltd. RT8139
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (8000ns min, 16000ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: I/O ports at a800 [size=256]
	Region 1: Memory at df800000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 04)
	Subsystem: Creative Labs CT4850 SBLive! Value
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (500ns min, 5000ns max)
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at a400 [size=32]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0b.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 01)
	Subsystem: Creative Labs Gameport Joystick
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Region 0: I/O ports at a000 [size=8]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0d.0 Network controller: AVM Audiovisuelles MKTG & Computer System GmbH A1 ISDN [Fritz] (rev 02)
	Subsystem: AVM Audiovisuelles MKTG & Computer System GmbH FRITZ!Card ISDN Controller
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 12
	Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=32]
	Region 1: I/O ports at 9800 [size=32]

00:0f.0 IDE interface: ALi Corporation M5229 IDE (rev c1) (prog-if 8a [Master SecP PriP])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (500ns min, 1000ns max)
	Interrupt: pin A routed to IRQ 0
	Region 4: I/O ports at 9400 [size=16]

01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15) (prog-if 00 [VGA])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (1250ns min, 250ns max)
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at e1000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: Memory at e6000000 (32-bit, prefetchable) [size=32M]
	Expansion ROM at e5ff0000 [disabled] [size=64K]
	Capabilities: [60] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [44] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

thunder@dbintra:/tmp$ 

				Thunder

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 189 bytes --]

                 reply	other threads:[~2003-10-31 13:10 UTC|newest]

Thread overview: [no followups] expand[flat|nested]  mbox.gz  Atom feed

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20031031131019.GA780@dbintra.dmz.lightweight.ods.org \
    --to=thunder@keepsake.ch \
    --cc=linux-kernel@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Be sure your reply has a Subject: header at the top and a blank line before the message body.

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®