Linux version 2.6.3 (root@scice) (gcc version 3.3.3 (Debian)) #3 Fri Feb 20 20:05:17 CET 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 0000000000095c00 (usable) BIOS-e820: 0000000000095c00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000016ff0000 (usable) BIOS-e820: 0000000016ff0000 - 0000000016ff8000 (ACPI data) BIOS-e820: 0000000016ff8000 - 0000000017000000 (ACPI NVS) BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved) 367MB LOWMEM available. On node 0 totalpages: 94192 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 90096 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 AMI ) @ 0x000fad50 ACPI: RSDT (v001 AMIINT AMIINT09 0x00000011 MSFT 0x00000097) @ 0x16ff0000 ACPI: FADT (v001 AMIINT AMIINT09 0x00000011 MSFT 0x00000097) @ 0x16ff0030 ACPI: DSDT (v001 TM5600 TMx86 0x00001000 MSFT 0x0100000d) @ 0x00000000 Built 1 zonelists Kernel command line: root=/dev/hda3 init=/sbin/minit video=sisfb:mode:1024x768x16,rate=60 sisfb: Options mode:1024x768x16,rate=60 sisfb: Invalid option rate=60 No local APIC present or hardware disabled Initializing CPU#0 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 599.310 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Memory: 369300k/376768k available (2165k kernel code, 6692k reserved, 416k data, 156k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 1101.82 BogoMIPS Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 0084893f 0081813f 00000000 00000000 CPU: After vendor identify, caps: 0084893f 0081813f 0000000e 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (32 bytes/line) CPU: L2 Cache: 512K (128 bytes/line) CPU: Processor revision 1.3.2.1, 600 MHz CPU: Code Morphing Software revision 4.2.7-8-278 CPU: 20011004 02:04 official release 4.2.7#7 CPU serial number disabled. CPU: After all inits, caps: 0080893f 0081813f 0000000e 00000000 CPU: Transmeta(tm) Crusoe(tm) Processor TM5600 stepping 03 Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfda61, last bus=0 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040116 ACPI: IRQ4 SCI: Edge set to Level Trigger. ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Power Resource [URP1] (off) ACPI: Power Resource [URP2] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 14 15) ACPI: PCI Interrupt Link [LNKP] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5 ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 9 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9 ACPI: No IRQ known for interrupt pin A of device 0000:00:10.0 ACPI: PCI Interrupt Link [LNKP] enabled at IRQ 10 PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' sisfb: Video ROM found and mapped to c00c0000 sisfb: Framebuffer at 0xd0000000, mapped to 0xd780a000, size 16384k sisfb: MMIO at 0xeffc0000, mapped to 0xd880b000, size 256k sisfb: Memory heap starting at 15360K sisfb: Using MMIO queue mode sisfb: Detected SiS301LV video bridge sisfb: Detected LCD PanelDelayCompensation 4 sisfb: Default mode is 1024x768x16 (60Hz) sisfb: Initial vbflags 0x4000012 sisfb: Added MTRRs sisfb: Installed SISFB_GET_INFO ioctl (80046ef8) sisfb: Installed SISFB_GET_VBRSTATUS ioctl (80046ef9) sisfb: 2D acceleration is enabled, scrolling mode ypan (auto-max) fb0: SIS 315PRO frame buffer device, Version 1.6.25 sisfb: (C) 2001-2004 Thomas Winischhofer. ikconfig 0.7 with /proc/config* devfs: v1.22 (20021013) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 SGI XFS with no debug enabled SGI XFS Quota Management subsystem Initializing Cryptographic API Activating ISA DMA hang workarounds. ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID0] ACPI: Processor [CPU1] (supports C1, 8 throttling states) Console: switching to colour frame buffer device 128x48 pty: 256 Unix98 ptys configured Linux agpgart interface v0.100 (c) Dave Jones [drm] Initialized sis 1.1.0 20030826 on minor 0 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ALI15X3: IDE controller at PCI slot 0000:00:10.0 ACPI: No IRQ known for interrupt pin A of device 0000:00:10.0 ALI15X3: chipset revision 196 ALI15X3: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:pio hda: TOSHIBA MK4025GAS, ATA DISK drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: QSI CD-RW/DVD-ROM SBW-242, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 78140160 sectors (40007 MB), CHS=65535/16/63, UDMA(100) /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 Console: switching to colour frame buffer device 128x48 mice: PS/2 mouse device common for all mice i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 Synaptics Touchpad, model: 1 Firmware: 5.8 Sensor: 29 new absolute packet format Touchpad has extended capability bits -> 4 multi-buttons, i.e. besides standard buttons -> multifinger detection -> palm detection input: SynPS/2 Synaptics TouchPad on isa0060/serio4 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) NET: Registered protocol family 1 NET: Registered protocol family 17 BIOS EDD facility v0.12 2004-Jan-26, 1 devices found Please report your BIOS at http://linux.dell.com/edd/results.html ACPI: (supports S0 S1 S3 S4 S5) XFS mounting filesystem hda3 Starting XFS recovery on filesystem: hda3 (dev: hda3) Ending XFS recovery on filesystem: hda3 (dev: hda3) VFS: Mounted root (xfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 156k freed XFS mounting filesystem hda1 Starting XFS recovery on filesystem: hda1 (dev: hda1) Ending XFS recovery on filesystem: hda1 (dev: hda1) XFS mounting filesystem loop0 Starting XFS recovery on filesystem: loop0 (dev: loop0) XFS internal error XFS_WANT_CORRUPTED_GOTO at line 1589 of file fs/xfs/xfs_alloc.c. Caller 0xc0198272 Call Trace: [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] Ending XFS recovery on filesystem: loop0 (dev: loop0) Adding 192772k swap on /dev/discs/disc0/part2. Priority:-1 extents:1 8139too Fast Ethernet driver 0.9.27 eth0: RealTek RTL8139 at 0xd886ee00, 00:0a:e6:ba:f6:c2, IRQ 5 eth0: Identified 8139 chip type 'RTL-8100B/8139D' eth0: link down hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 NET: Registered protocol family 10 Disabled Privacy Extensions on device c0379780(lo) IPv6 over IPv4 tunneling driver eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 eth0: no IPv6 routers present eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 eth0: no IPv6 routers present