Bootdata ok (command line is root=/dev/hdc6 vga=792 resume=/dev/hdc3 nmi_watchdog=0 console=ttyS0,57600) Linux version 2.6.9-rc1-mm4 (rafael@albercik) (gcc version 3.3.3 (SuSE Linux)) #2 Fri Sep 10 18:04:24 CEST 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ff40000 (usable) BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data) BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) No mptable found. On node 0 totalpages: 130880 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126784 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 PCI bridge 00:0a from 10de found. Setting "noapic". Overwrite with "apic" ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000f76e0 ACPI: RSDT (v001 A M I OEMRSDT 0x04000413 MSFT 0x00000097) @ 0x000000001ff40000 ACPI: FADT (v001 A M I OEMFACP 0x04000413 MSFT 0x00000097) @ 0x000000001ff40200 ACPI: OEMB (v001 A M I OEMBIOS 0x04000413 MSFT 0x00000097) @ 0x000000001ff50040 >>> ERROR: Invalid checksum ACPI: DSDT (v001 L5DK8 L5DK8013 0x00000013 INTL 0x02002026) @ 0x0000000000000000 Intel MultiProcessor Specification v1.1 Virtual Wire compatibility mode. OEM ID: ASUSTeK <6>Product ID: L5D <6>APIC at: 0xFEE00000 Processor #0 15:4 APIC version 16 I/O APIC #1 Version 17 at 0xFEC00000. Processors: 1 Checking aperture... CPU 0: aperture @ e8000000 size 128 MB Built 1 zonelists Initializing CPU#0 Kernel command line: root=/dev/hdc6 vga=792 resume=/dev/hdc3 nmi_watchdog=0 console=ttyS0,57600 PID hash table entries: 2048 (order: 11, 65536 bytes) time.c: Using 1.193182 MHz PIT timer. time.c: Detected 1795.406 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Memory: 509164k/523520k available (3004k kernel code, 13808k reserved, 1178k data, 168k init) Calibrating delay loop... 3555.32 BogoMIPS (lpj=1777664) Security Scaffold v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode There is already a security framework initialized, register_security failed. selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 256 (order: 0, 4096 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 0a ACPI: IRQ9 SCI: Edge set to Level Trigger. Using local APIC timer interrupts. Detected 12.468 MHz APIC timer. NET: Registered protocol family 16 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040816 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Embedded Controller [EC0] (gpe 37) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LUS0] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LUS1] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LUS2] (IRQs 3 4 5 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LKLN] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LAUI] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LKMO] (IRQs 3 4 5 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LKSM] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LTID] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LATA] (IRQs 3 4 6 7 10 11 12 *14 15) ACPI: Power Resource [GFAN] (off) PCI: Using ACPI for IRQ routing ** PCI interrupts are no longer routed automatically. If this ** causes a device to stop working, it is probably because the ** driver failed to call pci_enable_device(). As a temporary ** workaround, the "pci=routeirq" argument restores the old ** behavior. If this argument makes the device work again, ** please email the output of "lspci" to bjorn.helgaas@hp.com ** so I can fix the driver. agpgart: Detected AGP bridge 0 agpgart: Setting up Nforce3 AGP. agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 128M @ 0xe8000000 PCI-DMA: Disabling IOMMU. IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API vesafb: framebuffer at 0xd0000000, mapped to 0xffffff0000100000, size 6144k vesafb: mode is 1024x768x32, linelength=4096, pages=1 vesafb: scrolling: redraw vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12 Linux agpgart interface v0.100 (c) Dave Jones i8042: ACPI [PS2K] at I/O 0x60, 0x64, irq 1 i8042: ACPI [PS2M] at irq 12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A ACPI: PCI Interrupt Link [LKMO] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:06.1[B] -> GSI 10 (level, low) -> IRQ 10 RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE3-150: IDE controller at PCI slot 0000:00:08.0 NFORCE3-150: chipset revision 165 NFORCE3-150: not 100% native mode: will probe irqs later NFORCE3-150: BIOS didn't set cable bits correctly. Enabling workaround. NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:DMA ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hdb: TOSHIBA DVD-ROM SD-R2512, ATAPI CD/DVD-ROM drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: IC25N060ATMR04-0, ATA DISK drive ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide2... ide2: Wait for ready failed before probe ! Probing IDE interface ide3... ide3: Wait for ready failed before probe ! Probing IDE interface ide4... ide4: Wait for ready failed before probe ! Probing IDE interface ide5... ide5: Wait for ready failed before probe ! hdc: max request size: 1024KiB hdc: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100) hdc: cache flushes supported hdc: hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 hdc7 hdc8 hdc9 hdc10 > hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 Synaptics Touchpad, model: 1 Firmware: 5.9 180 degree mounted touchpad Sensor: 18 new absolute packet format Touchpad has extended capability bits -> four buttons -> palm detection input: SynPS/2 Synaptics TouchPad on isa0060/serio4 Please email the following PERFCTR INIT lines to mikpe@csd.uu.se To remove this message, rebuild the driver with CONFIG_PERFCTR_INIT_TESTS=n PERFCTR INIT: vendor 2, family 15, model 4, stepping 10, clock 1795406 kHz PERFCTR INIT: NITER == 64 PERFCTR INIT: loop overhead is 244 cycles PERFCTR INIT: rdtsc cost is 9.4 cycles (848 total) PERFCTR INIT: rdpmc cost is 10.7 cycles (935 total) PERFCTR INIT: rdmsr (counter) cost is 51.0 cycles (3508 total) PERFCTR INIT: rdmsr (evntsel) cost is 56.8 cycles (3881 total) PERFCTR INIT: wrmsr (counter) cost is 71.9 cycles (4851 total) PERFCTR INIT: wrmsr (evntsel) cost is 328.4 cycles (21264 total) PERFCTR INIT: read cr4 cost is 6.0 cycles (629 total) PERFCTR INIT: write cr4 cost is 67.0 cycles (4535 total) PERFCTR INIT: write LVTPC cost is 22.2 cycles (1671 total) PERFCTR INIT: sync_core cost is 163.9 cycles (10739 total) perfctr: driver 2.7.5, cpu type AMD K7/K8 at 1795406 kHz NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 28Kbytes TCP: Hash tables configured (established 32768 bind 4681) NET: Registered protocol family 1 PM: Reading pmdisk image. swsusp: Resume From Partition: /dev/hdc3 <3>swsusp: Suspend partition has wrong signature? pmdisk: Error -22 resuming PM: Resume from disk failed. ACPI: (supports S0 S1 S3 S4 S5) ACPI wakeup devices: MDM P0P1 LAN0 LAN1 USB0 USB1 USB2 SLPB kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 168k freed Adding 1534196k swap on /dev/hdc3. Priority:42 extents:1 EXT3 FS on hdc6, internal journal device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com kjournald starting. Commit interval 5 seconds EXT3 FS on hdc5, internal journal EXT3-fs: mounted filesystem with ordered data mode. ReiserFS: hdc9: found reiserfs format "3.6" with standard journal ReiserFS: hdc9: using ordered data mode ReiserFS: hdc9: journal params: device hdc9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdc9: checking transaction log (hdc9) ReiserFS: hdc9: Using r5 hash to sort names ReiserFS: hdc10: found reiserfs format "3.6" with standard journal ReiserFS: hdc10: using ordered data mode ReiserFS: hdc10: journal params: device hdc10, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdc10: checking transaction log (hdc10) ReiserFS: hdc10: Using r5 hash to sort names kjournald starting. Commit interval 5 seconds EXT3 FS on hdc8, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hdc7, internal journal EXT3-fs: mounted filesystem with ordered data mode. ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11 eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter PrefPort:A RlmtMode:Check Link State usbcore: registered new driver usbfs usbcore: registered new driver hub ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11 ohci_hcd 0000:00:02.0: nVidia Corporation nForce3 USB 1.1 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: irq 11, pci mem 0xfebfb000 ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 5 (level, low) -> IRQ 5 ohci_hcd 0000:00:02.1: nVidia Corporation nForce3 USB 1.1 (#2) usb 1-2: new low speed USB device using address 2 PCI: Setting latency timer of device 0000:00:02.1 to 64 ohci_hcd 0000:00:02.1: irq 5, pci mem 0xfebfc000 ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 10 (level, low) -> IRQ 10 ehci_hcd 0000:00:02.2: nVidia Corporation nForce3 USB 2.0 PCI: Setting latency timer of device 0000:00:02.2 to 64 ehci_hcd 0000:00:02.2: irq 10, pci mem 0xfebfdc00 ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3 PCI: cache line size of 64 is not supported by device 0000:00:02.2 ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 hub 3-0:1.0: USB hub found hub 3-0:1.0: 6 ports detected usb 1-2: USB disconnect, address 2 NET: Registered protocol family 17 ohci_hcd 0000:00:02.0: wakeup usb 1-2: new low speed USB device using address 3 eth0: network connection up using port A speed: 100 autonegotiation: yes duplex mode: full flowctrl: symmetric irq moderation: disabled scatter-gather: enabled Linux Kernel Card Services options: [pci] [cardbus] [pm] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9 ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 9 (level, low) -> IRQ 9 Yenta: CardBus bridge found at 0000:02:01.0 [1043:1854] Yenta: ISA IRQ mask 0x0008, PCI irq 9 Socket status: 30000006 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 ACPI: PCI interrupt 0000:02:01.1[B] -> GSI 11 (level, low) -> IRQ 11 Yenta: CardBus bridge found at 0000:02:01.1 [1043:1854] spurious 8259A interrupt: IRQ7. Yenta: ISA IRQ mask 0x0008, PCI irq 11 Socket status: 30000006 usbcore: registered new driver hiddev input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:02.0-2 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver ieee1394: Initialized config rom entry `ip1394' ohci1394: $Rev: 1226 $ Ben Collins ACPI: PCI interrupt 0000:02:01.2[C] -> GSI 11 (level, low) -> IRQ 11 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[feafd000-feafd7ff] Max Packet=[2048] NET: Registered protocol family 10 Disabled Privacy Extensions on device ffffffff804d7620(lo) IPv6 over IPv4 tunneling driver Disabled Privacy Extensions on device 000001001b11b600(sit0) ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:06.0 to 64 ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000319b175] ACPI: AC Adapter [AC0] (on-line) ACPI: Battery Slot [BAT0] (battery present) ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ACPI: Lid Switch [LID] ACPI: Fan [FN00] (off) ACPI: Processor [CPU1] (supports C1) ACPI: Thermal Zone [THRM] (56 C) intel8x0_measure_ac97_clock: measured 49491 usecs intel8x0: clocking to 48000 ALSA sound/pci/intel8x0.c:2844: joystick(s) found eth0: no IPv6 routers present SCSI subsystem initialized st: Version 20040403, fixed bufsize 32768, s/g segs 256 parport0: PC-style at 0x378 [PCSPP,TRISTATE] lp0: using parport0 (polling). drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic usbcore: registered new driver usbserial_generic usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0