Re: Linux-2.6.8 Hates DOS partitions

[Norbert van Nobelen <Norbert@edusupport.nl>]

msdos==vfat?
lilo installed in MBR (Unsafe in some situations!!)?
toggle bootability flag with fdisk (under linux ofcourse)?



On Wednesday 13 October 2004 19:31, Richard B. Johnson wrote:
> Hello DOS haters!
>
> I used to boot my system as:
>
> aic7xxx	[SCSI 0]
>  	/dev/sda  LILO boot record
>  	/dev/sda1 DOS drive C:
>  	/dev/sda5 DOS drive D:
>          [SCSI 1]
>  	/dev/sdb1 ext2 root "/"
>  	/dev/sdb2 swap-file
>  	[SCSI 2]
>  	/dev/sdc1 ext3 fs
>  	/dev/sdc2 swap-file
>  	/dev/sdc3 ext3 fs
>
>
> /dev/sdb1			/		ext2	rw,noatime  0   1
> /dev/sdc1			/alt		ext2	rw,noatime  0   2
> /dev/sdb2			none		swap	defaults    0	2
> /dev/sdc2			none		swap	defaults    0	2
> /dev/sdc3			/home/users	ext2	rw,noatime  0	2
> none				/proc		proc	defaults  0	2
> /dev/sda1			/dos/drive_C	msdos	defaults  0     2
> /dev/sda5			/dos/drive_D	msdos	defaults  0     2
>
>
> Then I added a completely different hard-disk to
> boot the following:
>
> LABEL=/ (/dev/hda2)     /                       ext3    defaults        1 1
> none                    /dev/pts                devpts  gid=5,mode=666  0 0
> none                    /dev/shm                tmpfs   defaults        0 0
> none                    /proc                   proc    defaults        0 0
> none                    /sys                    sysfs   defaults        0 0
> /dev/sdb1		/home/project		ext2	defaults	0 0
> /dev/sda1		/dos/drive_C		msdos	defaults	0 0
> /dev/sda5		/dos/drive_D		msdos	defaults	0 0
> /dev/hda3               swap                    swap    defaults        0 0
> /dev/sdb2               swap                    swap    defaults        0 0
> /dev/sdc2               swap                    swap    defaults        0 0
>
> Only the DOS partitions and the swap are used in this new configuration.
> This is a new "Fedora Linux 2" installation on a completely
> different IDE hard disk, in which I have to enable boot disks in
> the BIOS to boot the new system.
>
> Immediately after installing the new system I reverted (in the BIOS)
> to the original to make sure that I was still able to boot the old
> system and the DOS partition. Everything was fine.
>
> Then I installed linux-2.6.8 after building a new kernel with
> the old ".config" file used as `make oldconfig`. Everything was
> fine after that, also.
>
> I have now run for about a week and I can't boot the DOS partition
> anymore! I can boot from a DOS diskette and DOS sees 'C:', but
> not 'D:'. DOS 'thinks' that C: is bootable but I get "Missing
> operating system" when it attempts to boot. I have executed
> `fdisk /mbr`, and `sys C:`, as well as Norton's `ndd`. Everything
> seems to 'think' that the system should boot. However, it
> doesn't.
>
> I can boot Linux from an emergency floppy and re-run LILO to
> make my first SCSI bootable. It will boot Linux, but not
> DOS. I can also boot DOS from a floppy and access the
> "C:" partition, but not the "D:" one.
>
> It looks like the new operating system, linux-2.6.8, has
> done something bad when it used my SCSI disks for swap.
>
> I can copy everything  from C: and D: from within Linux
> and then re-do the DOS partitions, BUT.... bad stuff
> will happen again unless the cause is found. I never
> had any such problem with linux-2.4.26 and below. I
> could even execute dosemu and run DOS compilers, editors,
> and assemblers. Not anymore. DOSEMU-1.3.1 won't even
> compile with the new 'C' compiler, but that's another
> problem.
>
>
> Cheers,
> Dick Johnson
> Penguin : Linux version 2.6.8 on an i686 machine (5537.79 BogoMips).
>              Note 96.31% of all statistics are fiction.
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/