Linux version 2.6.12-rc6 (root@abc) (gcc version 3.3.6 (Debian 1:3.3.6-5)) #2 SMP Mon Jun 6 23:24:53 CEST 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003ff30000 (usable)
 BIOS-e820: 000000003ff30000 - 000000003ff40000 (ACPI data)
 BIOS-e820: 000000003ff40000 - 000000003fff0000 (ACPI NVS)
 BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 229376
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 225280 pages, LIFO batch:31
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
Intel MultiProcessor Specification v1.4
    Virtual Wire compatibility mode.
OEM ID: ASUSTek  Product ID:  APIC at: 0xFEE00000
Processor #0 15:2 APIC version 20
I/O APIC #2 Version 32 at 0xFEC00000.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Processors: 1
Allocating PCI resources starting at 40000000 (gap: 40000000:bfb80000)
Built 1 zonelists
Kernel command line: root=/dev/hda7 ro video=vesa:ywrap,mtrr vga=0x317 nmi_watchdog=1 profile=1 
kernel profiling enabled (shift: 1)
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
CPU 0 irqstacks, hard=c0551000 soft=c054f000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2606.438 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 898172k/917504k available (2949k kernel code, 18832k reserved, 1228k data, 208k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 5144.57 BogoMIPS (lpj=2572288)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
Total of 1 processors activated (5144.57 BogoMIPS).
WARNING: 1 siblings found for CPU0, should be 2
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=0
Brought up 1 CPUs
CPU0 attaching sched-domain:
 domain 0: span 1
  groups: 1
  domain 1: span 1
   groups: 1
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Using IRQ router PIIX/ICH [8086/24d0] at 0000:00:1f.0
PCI->APIC IRQ transform: 0000:00:1d.0[A] -> IRQ 16
PCI->APIC IRQ transform: 0000:00:1d.1[B] -> IRQ 19
PCI->APIC IRQ transform: 0000:00:1d.2[C] -> IRQ 18
PCI->APIC IRQ transform: 0000:00:1d.3[A] -> IRQ 16
PCI->APIC IRQ transform: 0000:00:1d.7[D] -> IRQ 23
PCI->APIC IRQ transform: 0000:00:1f.1[A] -> IRQ 18
PCI->APIC IRQ transform: 0000:00:1f.3[B] -> IRQ 17
PCI->APIC IRQ transform: 0000:00:1f.5[B] -> IRQ 17
PCI->APIC IRQ transform: 0000:01:00.0[A] -> IRQ 16
PCI->APIC IRQ transform: 0000:02:03.0[A] -> IRQ 20
PCI->APIC IRQ transform: 0000:02:05.0[A] -> IRQ 22
PCI->APIC IRQ transform: 0000:02:09.0[A] -> IRQ 21
PCI->APIC IRQ transform: 0000:02:0b.0[A] -> IRQ 23
PCI->APIC IRQ transform: 0000:02:0c.0[A] -> IRQ 20
PCI->APIC IRQ transform: 0000:02:0d.0[A] -> IRQ 21
PCI->APIC IRQ transform: 0000:02:0d.1[A] -> IRQ 21
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
vesafb: framebuffer at 0xfa000000, mapped to 0xf8880000, using 3072k, total 32768k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:7d40
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 865 Chipset.
agpgart: AGP aperture is 128M @ 0xf0000000
[drm] Initialized drm 1.0.0 20040925
[drm] Initialized mga 3.1.0 20021029 on minor 0: Matrox Graphics, Inc. MGA G550 AGP
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using monotonic_clock().
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
eth0: 3Com Gigabit LOM (3C940)
      PrefPort:A  RlmtMode:Check Link State
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
8139too Fast Ethernet driver 0.9.27
eth1: RealTek RTL8139 at 0xf8826000, 00:00:1c:db:d7:b7, IRQ 23
eth1:  Identified 8139 chip type 'RTL-8139B'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: SAMSUNG SP1614N, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TEAC DV-W50D, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 >
hdc: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[20]  MMIO=[feaff800-feafffff]  Max Packet=[2048]
ieee1394: raw1394: /dev/raw1394 device initialized
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebffc00
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.2
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ef00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ef20
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI #3
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ef40
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ef80
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
Advanced Linux Sound Architecture Driver Version 1.0.9rc2  (Thu Mar 24 10:33:39 2005 UTC).
specify port
PCI: Setting latency timer of device 0000:00:1f.5 to 64
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
AC'97 0 analog subsections not ready
intel8x0_measure_ac97_clock: measured 49387 usecs
intel8x0: clocking to 48000
ALSA device list:
  #0: Intel ICH5 with AD1985 at 0xfebff800, irq 17
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 64Kbytes
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
ip_conntrack version 2.1 (7168 buckets, 57344 max) - 224 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET: Registered protocol family 1
NET: Registered protocol family 17
Testing NMI watchdog ... OK.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 208k freed
kjournald starting.  Commit interval 5 seconds
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e018000047e68c]
Adding 1012052k swap on /dev/hda6.  Priority:-1 extents:1
EXT3 FS on hda7, internal journal
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux video capture interface: v1.00
saa7146: register extension 'dvb'.
saa7146: found saa7146 @ mem f8c46400 (revision 1, irq 21) (0x110a,0x0000).
DVB: registering new adapter (Fujitsu Siemens DVB-C).
adapter has MAC addr = 00:d0:5c:02:04:4b
dvb-ttpci: gpioirq unknown type=0 len=0
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 8000261d
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: DVB-C analog module @ card 0 detected, initializing MSP3400
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
saa7146_vv: saa7146 (0): registered device vbi0 [v4l2]
DVB: registering frontend 0 (VLSI VES1820 DVB-C)...
dvb-ttpci: found av7110-0.
saa7130/34: v4l2 driver version 0.2.12 loaded
saa7134[0]: found at 0000:02:0c.0, rev: 1, irq: 20, latency: 64, mmio: 0xfeafec00
saa7134[0]: subsystem: 1131:6752, board: BMK MPEX Tuner [card=23,insmod option]
saa7134[0]: board init: gpio is 10000
saa7134[0]: i2c eeprom 00: 31 11 52 67 06 80 00 01 00 00 00 00 00 00 01 00
saa7134[0]: i2c eeprom 10: 00 ff c2 0f ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tuner 2-0060: chip found @ 0xc0 (saa7134[0])
tuner 2-0060: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
saa6752hs: chip found @ 0x40
saa7134[0]: registered device video1 [v4l2]
saa7134[0]: registered device vbi1
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:02:0d.0, irq: 21, latency: 64, mmio: 0xfd7fe000
bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is 1822:0001
bttv0: using: Twinhan DST + clones [card=113,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00f789ff [init]
bttv0: using tuner=4
bttv0: add subdevice "dvb0"
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
bt878(0): Bt878 (rev 17) at 02:0d.1, irq: 21, latency: 64, memory: 0xfd7ff000
saa7134[0]/audio: audio carrier scan failed, using 5.500 MHz [default]
eth0: network connection up using port A
    speed:           100
    autonegotiation: yes
    duplex mode:     full
    flowctrl:        symmetric
    irq moderation:  disabled
    scatter-gather:  enabled