From: Pavel Machek <pavel@ucw.cz>
To: Andrew Morton <akpm@osdl.org>, Greg KH <greg@kroah.com>,
kernel list <linux-kernel@vger.kernel.org>
Subject: 2.6.16-rc1-mm1 usb hub problems
Date: Wed, 18 Jan 2006 21:57:52 +0100 [thread overview]
Message-ID: <20060118205752.GA1520@elf.ucw.cz> (raw)
Hi!
When I boot -mm1 in docking station, I get problems. First is ugly
warning near yenta:
Yenta: CardBus bridge found at 0000:09:02.0 [1014:0148]
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:09:02.0, mfunc 0x00001002, devctl 0x66
irq 11: nobody cared (try booting with the "irqpoll" option)
[<c013c904>] __report_bad_irq+0x24/0x90
[<c013c9ec>] note_interrupt+0x7c/0x1f0
[<c013c3e3>] handle_IRQ_event+0x33/0x70
[<c013c4ce>] __do_IRQ+0xae/0xc0
[<c0105309>] do_IRQ+0x19/0x30
[<c01036ca>] common_interrupt+0x1a/0x20
[<c013c3c7>] handle_IRQ_event+0x17/0x70
[<c013c482>] __do_IRQ+0x62/0xc0
[<c0105309>] do_IRQ+0x19/0x30
[<c01036ca>] common_interrupt+0x1a/0x20
[<c03bd433>] yenta_probe_cb_irq+0x83/0xf0
[<c03bd5cf>] ti12xx_override+0x12f/0x610
[<c047de1a>] pci_write+0x2a/0x30
[<c03bd224>] yenta_probe+0x4e4/0x550
[<c025ae3b>] pci_device_probe+0x5b/0x80
[<c03064dc>] driver_probe_device+0x4c/0xe0
[<c030663a>] __driver_attach+0x5a/0x60
[<c0305a6a>] bus_for_each_dev+0x3a/0x60
[<c0306386>] driver_attach+0x16/0x20
[<c03065e0>] __driver_attach+0x0/0x60
[<c0305d9c>] bus_add_driver+0x7c/0x140
[<c025a9f4>] __pci_register_driver+0x54/0x90
[<c01002f8>] init+0x88/0x210
[<c0100270>] init+0x0/0x210
[<c0101005>] kernel_thread_helper+0x5/0x10
handlers:
[<c03bc6d0>] (yenta_interrupt+0x0/0xc0)
Disabling IRQ #11
Yenta: ISA IRQ mask 0x04d8, PCI irq 9
...
and then I get problems with USB hub:
...
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 9 (level,
low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 9, io base 0x00001840
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ehci_hcd 0000:00:1d.7: Unlink after no-IRQ? Controller is probably
using the wrong IRQ.
usb 1-1: device not accepting address 2, error -110
usb 1-1: new high speed USB device using ehci_hcd and address 3
usb 1-1: device not accepting address 3, error -110
usb 1-1: new high speed USB device using ehci_hcd and address 4
usb 1-1: device not accepting address 4, error -110
usb 1-1: new high speed USB device using ehci_hcd and address 5
usb 1-1: device not accepting address 5, error -110
usbcore: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver
for USB modems and ISDN adapters
usbcore: registered new driver usblp
...
pavel@amd:~$ cat /proc/interrupts
CPU0
0: 39166 XT-PIC timer
1: 745 XT-PIC i8042
2: 0 XT-PIC cascade
5: 0 XT-PIC yenta, Intel 82801DB-ICH4
9: 422 XT-PIC acpi, ohci1394, yenta, yenta, uhci_hcd:usb4
11: 100000 XT-PIC yenta, ehci_hcd:usb1, uhci_hcd:usb2, uhci_hcd:usb3, eth0
12: 1221 XT-PIC i8042
14: 1700 XT-PIC ide0
NMI: 0
LOC: 0
ERR: 0
MIS: 0
pavel@amd:~$
Any ideas?
Pavel
--
Thanks, Sharp!
next reply other threads:[~2006-01-18 21:17 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-01-18 20:57 Pavel Machek [this message]
2006-01-18 21:53 ` Andrew Morton
2006-01-18 22:40 ` Pavel Machek
2006-01-20 5:29 Brown, Len
2006-01-20 16:10 ` Pavel Machek
2006-01-20 5:39 Brown, Len
2006-01-20 5:47 ` Andrew Morton
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060118205752.GA1520@elf.ucw.cz \
--to=pavel@ucw.cz \
--cc=akpm@osdl.org \
--cc=greg@kroah.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®