From: Luca <kronos@kronoz.cjb.net>
To: linux-kernel@vger.kernel.org
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Subject: Re: libata PATA drivers patch for 2.6.16-rc4
Date: Thu, 23 Feb 2006 18:18:17 +0100 [thread overview]
Message-ID: <20060223171817.GA7927@dreamland.darkstar.lan> (raw)
Alan Cox <alan@lxorguk.ukuu.org.uk> ha scritto:
> Various fixes and cleanups, some new functionality notably Promise
> 20246/2026x support which although basic should get it going with disk.
> Not 100% sure about ATAPI on PDC2026x yet.
>
> http://zeniv.linux.org.uk/~alan/IDE
Hi Alan,
I just tested the patch on my desktop (VIA VT8233A) and on my notebook
(SiS 5513): it boots correctly and performance (hdparm -T) looks good.
With atapi_enable all optical drives are recognized; I didn't try
burning (I'm out of disks...), but I'll do the test if it's useful.
This is the desktop:
lspci:
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233A ISA Bridge
Subsystem: VIA Technologies, Inc. VT8233A ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at d400 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
dmesg:
libata version 1.20 loaded.
pata_via 0000:00:11.1: version 0.1.4
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 11
ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0xD400 irq 14
via_do_set_mode: Mode=8 ast broken=Y udma=133 mul=4
ata1: dev 0 cfg 49:2f00 82:7c6b 83:7b09 84:4003 85:7c69 86:3a01 87:4003 88:407f
ata1: dev 0 ATA-7, max UDMA/133, 240121728 sectors: LBA
via_do_set_mode: Mode=8 ast broken=Y udma=133 mul=4
ata1: dev 1 cfg 49:0f00 82:346b 83:4001 84:4000 85:3469 86:0001 87:4000 88:101f
ata1: dev 1 ATA-4, max UDMA/66, 20044080 sectors: LBA
via_do_set_mode: Mode=12 ast broken=Y udma=133 mul=4
via_do_set_mode: Mode=69 ast broken=Y udma=133 mul=4
ata1: dev 0 configured for UDMA/100
via_do_set_mode: Mode=12 ast broken=Y udma=133 mul=4
via_do_set_mode: Mode=68 ast broken=Y udma=133 mul=4
ata1: dev 1 configured for UDMA/66
scsi0 : pata_via
Vendor: ATA Model: Maxtor 6Y120L0 Rev: YAR4
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: QUANTUM FIREBALL Rev: A03.
Type: Direct-Access ANSI SCSI revision: 05
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xD408 irq 15
via_do_set_mode: Mode=8 ast broken=Y udma=133 mul=4
ata2: dev 0 cfg 49:0b00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
ata2: dev 0 ATAPI, max UDMA/33
via_do_set_mode: Mode=8 ast broken=Y udma=133 mul=4
ata2: dev 1 cfg 49:0b00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
ata2: dev 1 ATAPI, max UDMA/33
via_do_set_mode: Mode=12 ast broken=Y udma=133 mul=4
via_do_set_mode: Mode=66 ast broken=Y udma=133 mul=4
ata2: dev 0 configured for UDMA/33
via_do_set_mode: Mode=12 ast broken=Y udma=133 mul=4
via_do_set_mode: Mode=66 ast broken=Y udma=133 mul=4
ata2: dev 1 configured for UDMA/33
scsi1 : pata_via
Vendor: _NEC Model: DVD_RW ND-1300A Rev: 1.0A
Type: CD-ROM ANSI SCSI revision: 05
Vendor: WAITEC Model: ALADAR/1 Rev: B1.5
Type: CD-ROM ANSI SCSI revision: 05
SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 sda8 > sda3
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 20044080 512-byte hdwr sectors (10263 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 20044080 512-byte hdwr sectors (10263 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2
sd 0:0:1:0: Attached scsi disk sdb
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 16x/40x writer cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: Attached scsi generic sg1 type 0
sr 1:0:0:0: Attached scsi generic sg2 type 5
sr 1:0:1:0: Attached scsi generic sg3 type 5
And this is the notebook:
lspci:
0000:00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS962 [MuTIOL Media IO] (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (prog-if 80 [Master])
Subsystem: ASUSTeK Computer Inc.: Unknown device 1658
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at b800 [size=16]
Capabilities: [58] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
dmesg:
libata version 1.20 loaded.
pata_sis 0000:00:02.5: version 0.1
ata1: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xB800 irq 14
ata1: dev 0 cfg 49:0f00 82:746b 83:49a8 84:4003 85:f469 86:0808 87:4003 88:203f
ata1: dev 0 ATA-5, max UDMA/100, 78140160 sectors: LBA
ata1: dev 0 configured for UDMA/100
scsi0 : pata_sis
Vendor: ATA Model: IC25N040ATCS04-0 Rev: CA4O
Type: Direct-Access ANSI SCSI revision: 05
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xB808 irq 15
ata2: dev 0 cfg 49:0b00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
ata2: dev 0 ATAPI, max UDMA/33
ata2: dev 0 configured for UDMA/33
scsi1 : pata_sis
Vendor: MATSHITA Model: UJDA740 DVD/CDRW Rev: 1.01
Type: CD-ROM ANSI SCSI revision: 05
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
Luca
--
Home: http://kronoz.cjb.net
K.R.O.N.O.S
Kinetic Replicant Optimized for Nocturnal Observation and Sabotage
next reply other threads:[~2006-02-23 17:17 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-02-23 17:18 Luca [this message]
-- strict thread matches above, loose matches on Subject: below --
2006-02-20 14:19 Alan Cox
2006-02-20 15:44 ` Meelis Roos
2006-02-20 17:40 ` Alan Cox
[not found] ` <b637ec0b0602200742j5780bfcck75f9090c91b8760f@mail.gmail.com>
2006-02-20 17:36 ` Alan Cox
2006-02-20 17:44 ` Fabio Comolli
2006-02-20 21:26 ` Francesco Biscani
2006-02-20 22:12 ` Mark Lord
2006-02-21 2:17 ` Francesco Biscani
2006-02-20 22:57 ` Alan Cox
2006-02-21 2:22 ` Francesco Biscani
2006-02-23 4:05 ` Ed Sweetman
2006-02-23 15:07 ` Alan Cox
2006-02-23 17:42 ` Francesco Biscani
2006-02-23 17:54 ` Chris Boot
2006-02-23 22:54 ` Ed Sweetman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060223171817.GA7927@dreamland.darkstar.lan \
--to=kronos@kronoz.cjb.net \
--cc=alan@lxorguk.ukuu.org.uk \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome