From: Bjorn Helgaas <bjorn.helgaas@hp.com>
To: Mike Miller <mike.miller@hp.com>
Cc: iss_storagedev@hp.com, linux-kernel@vger.kernel.org,
Andrew Morton <akpm@osdl.org>
Subject: [PATCH 5/7] CCISS: fix a few spelling errors
Date: Wed, 14 Jun 2006 17:11:38 -0600 [thread overview]
Message-ID: <200606141711.38975.bjorn.helgaas@hp.com> (raw)
In-Reply-To: <200606141707.27404.bjorn.helgaas@hp.com>
Fix a few spelling errors.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Index: rc5-mm3/drivers/block/cciss.c
===================================================================
--- rc5-mm3.orig/drivers/block/cciss.c 2006-06-14 15:16:13.000000000 -0600
+++ rc5-mm3/drivers/block/cciss.c 2006-06-14 15:16:44.000000000 -0600
@@ -129,7 +129,7 @@
{ 0x3215103C, "Smart Array E200i", &SA5_access},
};
-/* How long to wait (in millesconds) for board to go into simple mode */
+/* How long to wait (in milliseconds) for board to go into simple mode */
#define MAX_CONFIG_WAIT 30000
#define MAX_IOCTL_CONFIG_WAIT 1000
@@ -1117,7 +1117,7 @@
*
* Right now I'm using the getgeometry() function to do this, but this
* function should probably be finer grained and allow you to revalidate one
- * particualar logical volume (instead of all of them on a particular
+ * particular logical volume (instead of all of them on a particular
* controller).
*/
static int revalidate_allvol(ctlr_info_t *host)
@@ -1260,7 +1260,7 @@
return;
- /* Get information about the disk and modify the driver sturcture */
+ /* Get information about the disk and modify the driver structure */
size_buff = kmalloc(sizeof( ReadCapdata_struct), GFP_KERNEL);
if (size_buff == NULL)
goto mem_msg;
@@ -1335,7 +1335,7 @@
}
/* This function will add and remove logical drives from the Logical
- * drive array of the controller and maintain persistancy of ordering
+ * drive array of the controller and maintain persistency of ordering
* so that mount points are preserved until the next reboot. This allows
* for the removal of logical drives in the middle of the drive array
* without a re-ordering of those drives.
@@ -1482,7 +1482,7 @@
* clear_all = This flag determines whether or not the disk information
* is going to be completely cleared out and the highest_lun
* reset. Sometimes we want to clear out information about
- * the disk in preperation for re-adding it. In this case
+ * the disk in preparation for re-adding it. In this case
* the highest_lun should be left unchanged and the LunID
* should not be cleared.
*/
@@ -2597,7 +2597,7 @@
return IRQ_HANDLED;
}
/*
- * We cannot read the structure directly, for portablity we must use
+ * We cannot read the structure directly, for portability we must use
* the io functions.
* This is for debug only.
*/
@@ -2620,9 +2620,9 @@
readl(&(tb->TransportActive)));
printk(" Requested transport Method = 0x%x\n",
readl(&(tb->HostWrite.TransportRequest)));
- printk(" Coalese Interrupt Delay = 0x%x\n",
+ printk(" Coalesce Interrupt Delay = 0x%x\n",
readl(&(tb->HostWrite.CoalIntDelay)));
- printk(" Coalese Interrupt Count = 0x%x\n",
+ printk(" Coalesce Interrupt Count = 0x%x\n",
readl(&(tb->HostWrite.CoalIntCount)));
printk(" Max outstanding commands = 0x%d\n",
readl(&(tb->CmdsOutMax)));
next prev parent reply other threads:[~2006-06-14 23:11 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-06-14 23:07 [PATCH 0/7] CCISS cleanups Bjorn Helgaas
2006-06-14 23:08 ` [PATCH 1/7] CCISS: disable device when returning failure Bjorn Helgaas
2006-06-14 23:36 ` Jeff Garzik
2006-06-15 14:32 ` Miller, Mike (OS Dev)
2006-06-14 23:09 ` [PATCH 2/7] CCISS: request all PCI resources Bjorn Helgaas
2006-06-15 14:35 ` Miller, Mike (OS Dev)
2006-06-14 23:10 ` [PATCH 3/7] CCISS: announce cciss%d devices with PCI address/IRQ/DAC info Bjorn Helgaas
2006-06-14 23:37 ` Jeff Garzik
2006-06-15 14:37 ` Miller, Mike (OS Dev)
2006-06-14 23:10 ` [PATCH 4/7] CCISS: use ARRAY_SIZE without intermediates Bjorn Helgaas
2006-06-14 23:37 ` Jeff Garzik
2006-06-15 14:38 ` Miller, Mike (OS Dev)
2006-06-14 23:11 ` Bjorn Helgaas [this message]
2006-06-15 14:40 ` [PATCH 5/7] CCISS: fix a few spelling errors Miller, Mike (OS Dev)
2006-06-14 23:12 ` [PATCH 6/7] CCISS: remove parens around return values Bjorn Helgaas
2006-06-15 14:42 ` Miller, Mike (OS Dev)
[not found] ` <200606141713.46497.bjorn.helgaas@hp.com>
2006-06-15 4:08 ` [PATCH 7/7] CCISS: run through Lindent Bjorn Helgaas
[not found] ` <c6b285c60606150114h273f5ceue19bcea43937e86c@mail.gmail.com>
2006-06-15 8:35 ` [PATCH 0/7] CCISS cleanups Laura Garcia
2006-06-15 11:50 ` Jeff Garzik
2006-06-15 16:57 ` [PATCH 8/7] CCISS: tidy up product table indentation Bjorn Helgaas
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200606141711.38975.bjorn.helgaas@hp.com \
--to=bjorn.helgaas@hp.com \
--cc=akpm@osdl.org \
--cc=iss_storagedev@hp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mike.miller@hp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®