From: Vitaly Bordug <vbordug@ru.mvista.com>
To: Li Yang-r58472 <LeoLi@freescale.com>
Cc: "'Paul Mackerras'" <paulus@samba.org>,
linuxppc-dev@ozlabs.org,
Phillips Kim-R1AAHA <Kim.Phillips@freescale.com>,
Chu hanjin-r52514 <Hanjin.Chu@freescale.com>,
Yin Olivia-r63875 <Hong-Hua.Yin@freescale.com>,
"'linux-kernel@vger.kernel.org'" <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 1/7] powerpc: Add mpc8360epb platform support
Date: Wed, 28 Jun 2006 20:58:39 +0400 [thread overview]
Message-ID: <20060628205839.1e12a5a4@vitb.ru.mvista.com> (raw)
In-Reply-To: <9FCDBA58F226D911B202000BDBAD467306E04FD2@zch01exm40.ap.freescale.net>
On Wed, 28 Jun 2006 22:23:03 +0800
Li Yang-r58472 <LeoLi@freescale.com> wrote:
> The patch adds mpc8360e MDS Processor Board support.
Far too short comment I guess.. There should be some information at least, what u-boot modifications are required, what family being introduced, etc.
>
> Signed-off-by: Li Yang <leoli@freescale.com>
> Signed-off-by: Yin Olivia <hong-hua.yin@freescale.com>
> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
>
> ---
> arch/powerpc/platforms/83xx/Kconfig | 13 ++
> arch/powerpc/platforms/83xx/Makefile | 1
> arch/powerpc/platforms/83xx/mpc8360e_pb.c | 213 +++++++++++++++++++++++++++++
> arch/powerpc/platforms/83xx/mpc8360e_pb.h | 31 ++++
> 4 files changed, 258 insertions(+), 0 deletions(-)
>
> diff --git a/arch/powerpc/platforms/83xx/Kconfig b/arch/powerpc/platforms/83xx/Kconfig
> index 7675e67..04c4508 100644
> --- a/arch/powerpc/platforms/83xx/Kconfig
> +++ b/arch/powerpc/platforms/83xx/Kconfig
> @@ -16,6 +16,13 @@ config MPC834x_SYS
> 3 PCI slots. The PIBs PCI initialization is the bootloader's
> responsiblilty.
>
> +config MPC8360E_PB
> + bool "Freescale MPC8360E PB"
> + select DEFAULT_UIMAGE
> + select QUICC_ENGINE
> + help
> + This option enables support for the MPC836x EMDS Processor Board.
> +
> endchoice
I don't think this is really required option. I guess 836x + QUICC_ENGINE should be enough (with a proviso that 8360 won't boot without qe.
>
> config MPC834x
> @@ -24,4 +31,10 @@ config MPC834x
> select PPC_INDIRECT_PCI
> default y if MPC834x_SYS
>
> +config MPC836x
> + bool
> + select PPC_UDBG_16550
debug option made default?
> + select PPC_INDIRECT_PCI
> + default y if MPC8360E_PB
> +
> endmenu
> diff --git a/arch/powerpc/platforms/83xx/Makefile b/arch/powerpc/platforms/83xx/Makefile
> index 5c72367..0c9ea5c 100644
> --- a/arch/powerpc/platforms/83xx/Makefile
> +++ b/arch/powerpc/platforms/83xx/Makefile
> @@ -4,3 +4,4 @@ #
> obj-y := misc.o
> obj-$(CONFIG_PCI) += pci.o
> obj-$(CONFIG_MPC834x_SYS) += mpc834x_sys.o
> +obj-$(CONFIG_MPC8360E_PB) += mpc8360e_pb.o
> diff --git a/arch/powerpc/platforms/83xx/mpc8360e_pb.c b/arch/powerpc/platforms/83xx/mpc8360e_pb.c
> new file mode 100644
> index 0000000..b4ddb0a
> --- /dev/null
> +++ b/arch/powerpc/platforms/83xx/mpc8360e_pb.c
> @@ -0,0 +1,213 @@
> +/*
> + * Copyright (C) Freescale Semicondutor, Inc. 2006. All rights reserved.
> + *
> + * Author: Li Yang <LeoLi@freescale.com>
> + * Yin Olivia <Hong-hua.Yin@freescale.com>
> + *
> + * Description:
> + * MPC8360E MDS PB board specific routines.
> + *
> + * Changelog:
> + * Jun 21, 2006 Initial version
> + *
No changelog entries for new files please... git tracks it good enough.
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the License, or (at your
> + * option) any later version.
> + */
> +
> +#include <linux/config.h>
> +#include <linux/stddef.h>
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/errno.h>
> +#include <linux/reboot.h>
> +#include <linux/pci.h>
> +#include <linux/kdev_t.h>
> +#include <linux/major.h>
> +#include <linux/console.h>
> +#include <linux/delay.h>
> +#include <linux/seq_file.h>
> +#include <linux/root_dev.h>
> +#include <linux/initrd.h>
> +
> +#include <asm/system.h>
> +#include <asm/atomic.h>
> +#include <asm/time.h>
> +#include <asm/io.h>
> +#include <asm/machdep.h>
> +#include <asm/ipic.h>
> +#include <asm/bootinfo.h>
> +#include <asm/irq.h>
> +#include <asm/prom.h>
> +#include <asm/udbg.h>
> +#include <sysdev/fsl_soc.h>
> +#ifdef CONFIG_QUICC_ENGINE
> +#include <asm/immap_qe.h>
> +#include <asm/qe_ic.h>
> +#endif /* CONFIG_QUICC_ENGINE */
> +#include "mpc83xx.h"
> +#include "mpc8360e_pb.h"
> +
> +#undef DEBUG
> +
hmmm? Does it relate nicely with below ?
> +#ifdef DEBUG
> +#define DBG(fmt...) udbg_printf(fmt)
> +#else
> +#define DBG(fmt...)
> +#endif
> +
> +
> +#ifndef CONFIG_PCI
> +unsigned long isa_io_base = 0;
> +unsigned long isa_mem_base = 0;
> +#endif
> +
> +#ifdef CONFIG_QUICC_ENGINE
> +extern void qe_reset(void);
> +extern int par_io_of_config(struct device_node *np);
> +#endif /* CONFIG_QUICC_ENGINE */
I bet this should go to the .h file...
> +
> +/* ************************************************************************
> + *
> + * Setup the architecture
> + *
> + */
> +static void __init mpc8360_sys_setup_arch(void)
> +{
> + struct device_node *np;
> +
> +#ifdef CONFIG_QUICC_ENGINE
> + u8 *bcsr_regs;
> +#endif
> +
> + if (ppc_md.progress)
> + ppc_md.progress("mpc8360_sys_setup_arch()", 0);
> +
> + np = of_find_node_by_type(NULL, "cpu");
> + if (np != 0) {
> + unsigned int *fp =
> + (int *)get_property(np, "clock-frequency", NULL);
> + if (fp != 0)
> + loops_per_jiffy = *fp / HZ;
> + else
> + loops_per_jiffy = 50000000 / HZ;
> + of_node_put(np);
> + }
> +#ifdef CONFIG_PCI
> + for (np = NULL; (np = of_find_node_by_type(np, "pci")) != NULL;)
> + add_bridge(np);
> +
> + ppc_md.pci_swizzle = common_swizzle;
> + ppc_md.pci_exclude_device = mpc83xx_exclude_device;
> +#endif
> +
> +#ifdef CONFIG_QUICC_ENGINE
> + qe_reset();
> +
> + for (np = NULL; (np = of_find_node_by_name(np, "ucc")) != NULL;)
> + par_io_of_config(np);
> +
> + /* Reset the Ethernet PHY */
> + bcsr_regs = (u8 *) ioremap(BCSR_PHYS_ADDR, BCSR_SIZE);
> + bcsr_regs[9] &= ~0x20;
> + udelay(1000);
> + bcsr_regs[9] |= 0x20;
> + iounmap(bcsr_regs);
> +
And if we have a design, which do not contain real ethernet UCC usage? Or UCC geth is disabled somehow explicitly? Stuff like that normally goes to the callback that is going to be triggered upon Etherbet init.
> +#endif /* CONFIG_QUICC_ENGINE */
> +
> +#ifdef CONFIG_BLK_DEV_INITRD
> + if (initrd_start)
> + ROOT_DEV = Root_RAM0;
> + else
> +#endif
> +#ifdef CONFIG_ROOT_NFS
> + ROOT_DEV = Root_NFS;
> +#else
> + ROOT_DEV = Root_HDA1;
> +#endif
> +}
> +
> +void __init mpc8360_sys_init_IRQ(void)
> +{
> + u8 senses[8] = {
> + 0, /* EXT 0 */
> + IRQ_SENSE_LEVEL, /* EXT 1 */
> + IRQ_SENSE_LEVEL, /* EXT 2 */
> + 0, /* EXT 3 */
> +#ifdef CONFIG_PCI
> + IRQ_SENSE_LEVEL, /* EXT 4 */
> + IRQ_SENSE_LEVEL, /* EXT 5 */
> + IRQ_SENSE_LEVEL, /* EXT 6 */
> + IRQ_SENSE_LEVEL, /* EXT 7 */
> +#else
> + 0, /* EXT 4 */
> + 0, /* EXT 5 */
> + 0, /* EXT 6 */
> + 0, /* EXT 7 */
> +#endif
> + };
> +
> + ipic_init(get_immrbase() + 0x00700, 0, 0, senses, 8);
> +
> + /* Initialize the default interrupt mapping priorities,
> + * in case the boot rom changed something on us.
> + */
> + ipic_set_default_priority();
> +
> +#ifdef CONFIG_QUICC_ENGINE
> + qe_ic_init(get_qe_base() + 0x00000080,
> + (QE_IC_LOW_SIGNAL | QE_IC_HIGH_SIGNAL), QE_IRQ_OFFSET);
> +#endif /* CONFIG_QUICC_ENGINE */
> +}
> +
> +#if defined(CONFIG_I2C_MPC) && defined(CONFIG_SENSORS_DS1374)
> +extern ulong ds1374_get_rtc_time(void);
> +extern int ds1374_set_rtc_time(ulong);
> +
> +static int __init mpc8360_rtc_hookup(void)
> +{
> + struct timespec tv;
> +
> + ppc_md.get_rtc_time = ds1374_get_rtc_time;
> + ppc_md.set_rtc_time = ds1374_set_rtc_time;
> +
> + tv.tv_nsec = 0;
> + tv.tv_sec = (ppc_md.get_rtc_time) ();
> + do_settimeofday(&tv);
> +
> + return 0;
> +}
> +
> +late_initcall(mpc8360_rtc_hookup);
> +#endif
> +
> +/*
> + * Called very early, MMU is off, device-tree isn't unflattened
> + */
> +static int __init mpc8360_sys_probe(void)
> +{
> + char *model = of_get_flat_dt_prop(of_get_flat_dt_root(),
> + "model", NULL);
> + if (model == NULL)
> + return 0;
> + if (strcmp(model, "MPC8360EPB"))
> + return 0;
> +
> + DBG("MPC8360EMDS-PB found\n");
> +
> + return 1;
> +}
> +
> +define_machine(mpc8360_sys) {
> + .name = "MPC8360E PB",
> + .probe = mpc8360_sys_probe,
> + .setup_arch = mpc8360_sys_setup_arch,
> + .init_IRQ = mpc8360_sys_init_IRQ,
> + .get_irq = ipic_get_irq,
> + .restart = mpc83xx_restart,
> + .time_init = mpc83xx_time_init,
> + .calibrate_decr = generic_calibrate_decr,
> + .progress = udbg_progress,
> +};
> diff --git a/arch/powerpc/platforms/83xx/mpc8360e_pb.h b/arch/powerpc/platforms/83xx/mpc8360e_pb.h
> new file mode 100644
> index 0000000..4243f4a
> --- /dev/null
> +++ b/arch/powerpc/platforms/83xx/mpc8360e_pb.h
> @@ -0,0 +1,31 @@
> +/*
> + * Copyright (C) Freescale Semicondutor, Inc. 2006. All rights reserved.
> + *
> + * Author: Li Yang <LeoLi@freescale.com>
> + * Yin Olivia <Hong-hua.Yin@freescale.com>
> + *
> + * Description:
> + * MPC8360E MDS PB board specific header.
> + *
> + * Changelog:
> + * Jun 21, 2006 Initial version
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the License, or (at your
> + * option) any later version.
> + *
> + */
> +
> +#ifndef __MACH_MPC83XX_SYS_H__
> +#define __MACH_MPC83XX_SYS_H__
> +
> +#define BCSR_PHYS_ADDR ((uint)0xf8000000)
> +#define BCSR_SIZE ((uint)(32 * 1024))
> +
> +#define PIRQA MPC83xx_IRQ_EXT4
> +#define PIRQB MPC83xx_IRQ_EXT5
> +#define PIRQC MPC83xx_IRQ_EXT6
> +#define PIRQD MPC83xx_IRQ_EXT7
> +
Hrm, isn't PCI irq stuff encoded to the dts? Upper pci-related defines seem redundant...
> +#endif /* __MACH_MPC83XX_SYS_H__ */
>
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev
>
>
--
Sincerely,
Vitaly
next prev parent reply other threads:[~2006-06-28 17:01 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-06-28 14:23 Li Yang-r58472
2006-06-28 16:58 ` Vitaly Bordug [this message]
2006-06-29 9:28 Li Yang-r58472
2006-06-29 18:03 ` Andy Fleming
2006-06-29 18:51 ` Vitaly Bordug
2006-06-29 19:18 ` Andy Fleming
2006-06-29 19:56 ` Vitaly Bordug
2006-06-29 21:04 ` Andy Fleming
2006-06-29 22:10 ` Vitaly Bordug
2006-06-30 7:58 Li Yang-r58472
2006-06-30 10:27 Li Yang-r58472
2006-07-01 9:00 ` Benjamin Herrenschmidt
2006-07-04 7:00 Li Yang-r58472
2006-07-04 22:39 ` Benjamin Herrenschmidt
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060628205839.1e12a5a4@vitb.ru.mvista.com \
--to=vbordug@ru.mvista.com \
--cc=Hanjin.Chu@freescale.com \
--cc=Hong-Hua.Yin@freescale.com \
--cc=Kim.Phillips@freescale.com \
--cc=LeoLi@freescale.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linuxppc-dev@ozlabs.org \
--cc=paulus@samba.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®