mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Lennert Buytenhek <buytenh@wantstofly.org>
To: Michael Buesch <mb@bu3sch.de>
Cc: "Török Edvin" <edwintorok@gmail.com>,
	zambrano@broadcom.com, netdev@vger.kernel.org,
	linux-kernel@vger.kernel.org, power@bughost.org
Subject: Re: [PATCH] b44: power down PHY when interface down
Date: Sun, 1 Jul 2007 17:00:06 +0200	[thread overview]
Message-ID: <20070701150006.GE7929@xi.wantstofly.org> (raw)
In-Reply-To: <200707011223.17235.mb@bu3sch.de>

On Sun, Jul 01, 2007 at 12:23:16PM +0200, Michael Buesch wrote:

> > More or less.  You can't add the resistances like that, since the
> > bus isolation chip buffers the IDSEL signal, but it is correct that
> > if the host's IDSEL resistor is larger than a certain value, the
> > combination of the resistive coupling of IDSEL plus the extra buffer
> > in the isolator might be causing the IDSEL input on the 'guest' PCI
> > board to assert too late (or not assert at all), causing config
> > accesses to fail.
> > 
> > (This also depends on the specific 'guest' PCI board used, as you
> > noted, due to differing IDSEL trace lengths/capacitances and input
> > pin capacitances on different PCI boards.  Also, it might work at
> > 33 MHz but not work at 66 MHz, etc.)
> 
> It doesn't work on any of my boards :(

What extender board is this?  Do you have docs/schematics?
And what motherboard brand/type?


> > If you feel adventurous, you could try to hack around this by
> > figuring out which AD[31:16] line this PCI slot's IDSEL line is
> > resistively coupled to (depends on the slot), and then adding
> > another parallel resistor on the board itself to make the bus
> > isolator's input buffer charge faster.  Note that this does
> > increase the load on that specific AD[] line, which might cause
> > other funny effects.
> 
> Well, but how to find out to which address line it's connected to?
> Pretty hard to follow the PCB traces, especially since it's
> multilayered.

Actually, the IDSEL resistor would be on the computer's
motherboard, not on the PCI board.  And to which address line
the IDSEL line is connected depends on which PCI slot on the
motherboard you're looking at.

A multimeter should do the trick, but I would advise against this
if you're not totally comfortable with hacking hardware.

  reply	other threads:[~2007-07-01 15:00 UTC|newest]

Thread overview: 21+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2007-06-30 11:47 Török Edvin
2007-06-30 12:05 ` Matthew Garrett
2007-06-30 14:44   ` Arjan van de Ven
2007-06-30 15:19     ` Matthew Garrett
2007-06-30 15:25       ` Lennert Buytenhek
2007-07-01 13:02       ` Török Edvin
2007-06-30 16:42     ` PM policy, hotplug, power saving (was Re: [PATCH] b44: power down PHY when interface down) Jeff Garzik
2007-06-30 18:10       ` Stephen Hemminger
2007-06-30 18:31       ` PM policy, hotplug, power saving and WoL Henrique de Moraes Holschuh
2007-07-01  4:51       ` PM policy, hotplug, power saving (was Re: [PATCH] b44: power down PHY when interface down) Kyle Moffett
2007-06-30 21:53 ` [PATCH] b44: power down PHY when interface down Michael Buesch
2007-06-30 22:03   ` Lennert Buytenhek
2007-06-30 22:24     ` Michael Buesch
2007-06-30 23:17       ` Lennert Buytenhek
2007-07-01 10:23         ` Michael Buesch
2007-07-01 15:00           ` Lennert Buytenhek [this message]
2007-07-01 15:29             ` Michael Buesch
2007-07-01 20:20             ` Michael Buesch
     [not found] ` <20070630081302.66b1d984@oldman>
2007-07-01 12:49   ` Török Edvin
2007-07-01 12:55     ` Michael Buesch
2007-07-01 13:25 Török Edvin

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20070701150006.GE7929@xi.wantstofly.org \
    --to=buytenh@wantstofly.org \
    --cc=edwintorok@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mb@bu3sch.de \
    --cc=netdev@vger.kernel.org \
    --cc=power@bughost.org \
    --cc=zambrano@broadcom.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®