From: Jesper Nilsson <jesper.nilsson@axis.com>
To: Andrew Morton <akpm@linux-foundation.org>,
sam@ravnborg.org, Mikael Starvik <mikael.starvik@axis.com>,
Jesper Nilsson <jesper.nilsson@axis.com>,
linux-kernel@vger.kernel.org, Jan Dittmer <jdi@l4x.org>
Subject: [PATCH] CRIS: avoid using arch links in Kconfig
Date: Wed, 21 Nov 2007 10:03:46 +0100 [thread overview]
Message-ID: <20071121090346.GD14797@axis.com> (raw)
Improve including of architecture dependent Kconfig files.
- Always include the architecture dependent Kconfig files.
- Wrap architecture dependent Kconfig files inside an appropriate
"if ETRAX_ARCH_Vxx" block.
This makes it possible to run the configuration even without the arch links,
which are created later in the build process.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
---
Kconfig | 5 +++--
arch-v10/Kconfig | 4 ++++
arch-v10/drivers/Kconfig | 4 ++++
arch-v32/Kconfig | 4 ++++
arch-v32/drivers/Kconfig | 4 ++++
5 files changed, 19 insertions(+), 2 deletions(-)
diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig
index 222da15..d296e55 100644
--- a/arch/cris/Kconfig
+++ b/arch/cris/Kconfig
@@ -150,6 +150,7 @@ config ETRAX_FLASH_BUSWIDTH
Width in bytes of the Flash bus (1, 2 or 4). Is usually 2.
source arch/cris/arch-v10/Kconfig
+source arch/cris/arch-v32/Kconfig
endmenu
@@ -157,8 +158,8 @@ source "net/Kconfig"
# bring in ETRAX built-in drivers
menu "Drivers for built-in interfaces"
-# arch/cris/arch is a symlink to correct arch (arch-v10 or arch-v32)
-source arch/cris/arch/drivers/Kconfig
+source arch/cris/arch-v10/drivers/Kconfig
+source arch/cris/arch-v32/drivers/Kconfig
endmenu
diff --git a/arch/cris/arch-v10/Kconfig b/arch/cris/arch-v10/Kconfig
index f1ce6f6..1d61fae 100644
--- a/arch/cris/arch-v10/Kconfig
+++ b/arch/cris/arch-v10/Kconfig
@@ -1,3 +1,5 @@
+if ETRAX_ARCH_V10
+
# ETRAX 100LX v1 has a MMU "feature" requiring a low mapping
config CRIS_LOW_MAP
bool
@@ -451,3 +453,5 @@ config ETRAX_POWERBUTTON_BIT
default "25"
help
Configure where power button is connected.
+
+endif
diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig
index faf8b4d..6011ff4 100644
--- a/arch/cris/arch-v10/drivers/Kconfig
+++ b/arch/cris/arch-v10/drivers/Kconfig
@@ -1,3 +1,5 @@
+if ETRAX_ARCH_V10
+
config ETRAX_ETHERNET
bool "Ethernet support"
depends on ETRAX_ARCH_V10
@@ -845,3 +847,5 @@ config ETRAX_DS1302_TRICKLE_CHARGE
1 = 2kohm, 2 = 4kohm, 3 = 4kohm
4 = 1 diode, 8 = 2 diodes
Allowed values are (increasing current): 0, 11, 10, 9, 7, 6, 5
+
+endif
diff --git a/arch/cris/arch-v32/Kconfig b/arch/cris/arch-v32/Kconfig
index 4f79d8e..d8acaa9 100644
--- a/arch/cris/arch-v32/Kconfig
+++ b/arch/cris/arch-v32/Kconfig
@@ -1,3 +1,5 @@
+if ETRAX_ARCH_V32
+
config ETRAX_DRAM_VIRTUAL_BASE
hex
depends on ETRAX_ARCH_V32
@@ -294,3 +296,5 @@ config ETRAX_DEF_GIO_PE_OUT
help
Configures the initial data for the general port E bits. Most
products should use 00000 here.
+
+endif
diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig
index 7f72d7c..7952ee8 100644
--- a/arch/cris/arch-v32/drivers/Kconfig
+++ b/arch/cris/arch-v32/drivers/Kconfig
@@ -1,3 +1,5 @@
+if ETRAX_ARCH_V32
+
config ETRAX_ETHERNET
bool "Ethernet support"
depends on ETRAX_ARCH_V32
@@ -622,3 +624,5 @@ config ETRAX_STREAMCOPROC
help
This option enables a driver for the stream co-processor
for cryptographic operations.
+
+endif
/^JN - Jesper Nilsson
--
Jesper Nilsson -- jesper.nilsson@axis.com
next reply other threads:[~2007-11-21 9:04 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-11-21 9:03 Jesper Nilsson [this message]
2007-11-21 9:55 ` Sam Ravnborg
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20071121090346.GD14797@axis.com \
--to=jesper.nilsson@axis.com \
--cc=akpm@linux-foundation.org \
--cc=jdi@l4x.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mikael.starvik@axis.com \
--cc=sam@ravnborg.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®