From: "Hemmann, Volker Armin" <volker.armin.hemmann@tu-clausthal.de>
To: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org, linux-ide@vger.kernel.org
Subject: Re: question about sata-error on boot.
Date: Fri, 7 Dec 2007 14:32:08 +0100 [thread overview]
Message-ID: <200712071432.08699.volker.armin.hemmann@tu-clausthal.de> (raw)
In-Reply-To: <20071106221556.55c3cd0b.akpm@linux-foundation.org>
Hi,
On Mittwoch, 7. November 2007, Andrew Morton wrote:
> > On Fri, 2 Nov 2007 19:34:20 +0100 "Hemmann, Volker Armin"
> > <volker.armin.hemmann@tu-clausthal.de> wrote: Hi,
>
> (cc linux-ide)
>
> > for some time (and I can't say for how long, but the board is less than a
> > month old) I get this error on boot:
> >
> > [ 42.116273] ahci 0000:00:0a.0: version 2.2
> > [ 42.116482] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
> > [ 42.116653] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI
> > 23 (level, low) -> IRQ 23
> > [ 43.119478] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps
> > 0xf impl IDE mode
> > [ 43.119778] ahci 0000:00:0a.0: flags: 64bit led clo pmp pio
> > [ 43.119943] PCI: Setting latency timer of device 0000:00:0a.0 to 64
> > [ 43.120149] scsi0 : ahci
> > [ 43.120365] scsi1 : ahci
> > [ 43.120556] scsi2 : ahci
> > [ 43.120741] scsi3 : ahci
> > [ 43.120927] ata1: SATA max UDMA/133 cmd 0xffffc20000014100 ctl
> > 0x0000000000000000 bmdma 0x0000000000000000 irq 315
> > [ 43.121227] ata2: SATA max UDMA/133 cmd 0xffffc20000014180 ctl
> > 0x0000000000000000 bmdma 0x0000000000000000 irq 315
> > [ 43.121526] ata3: SATA max UDMA/133 cmd 0xffffc20000014200 ctl
> > 0x0000000000000000 bmdma 0x0000000000000000 irq 315
> > [ 43.121826] ata4: SATA max UDMA/133 cmd 0xffffc20000014280 ctl
> > 0x0000000000000000 bmdma 0x0000000000000000 irq 315
> > [ 43.934296] ata1: softreset failed (1st FIS failed)
> > [ 43.934461] ata1: reset failed (errno=-5), retrying in 10 secs
> > [ 53.885194] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> > [ 53.885890] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max
> > UDMA/133 [ 53.886056] ata1.00: 312581808 sectors, multi 16: LBA48
> > [ 53.886804] ata1.00: configured for UDMA/133
> > [ 54.201147] ata2: SATA link down (SStatus 0 SControl 300)
> > [ 54.517101] ata3: SATA link down (SStatus 0 SControl 300)
> > [ 54.833055] ata4: SATA link down (SStatus 0 SControl 300)
this is gone with 2.6.22.13 an 2.6.23.9:
[ 33.277039] scsi0 : ahci
[ 33.277262] scsi1 : ahci
[ 33.277454] scsi2 : ahci
[ 33.277645] scsi3 : ahci
[ 33.277826] ata1: SATA max UDMA/133 cmd 0xffffc20000020100 ctl
0x0000000000000000 bmdma 0x0000000000000000 irq 315
[ 33.278120] ata2: SATA max UDMA/133 cmd 0xffffc20000020180 ctl
0x0000000000000000 bmdma 0x0000000000000000 irq 315
[ 33.278414] ata3: SATA max UDMA/133 cmd 0xffffc20000020200 ctl
0x0000000000000000 bmdma 0x0000000000000000 irq 315
[ 33.278708] ata4: SATA max UDMA/133 cmd 0xffffc20000020280 ctl
0x0000000000000000 bmdma 0x0000000000000000 irq 315
[ 33.751855] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 33.752659] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133
[ 33.752821] ata1.00: 312581808 sectors, multi 16: LBA48
[ 33.753574] ata1.00: configured for UDMA/133
[ 34.067809] ata2: SATA link down (SStatus 0 SControl 300)
[ 34.383762] ata3: SATA link down (SStatus 0 SControl 300)
[ 34.699717] ata4: SATA link down (SStatus 0 SControl 300)
[ 34.700029] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0
PQ: 0 ANSI: 5
[ 34.700377] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042
MB)
[ 34.700544] sd 0:0:0:0: [sda] Write Protect is off
[ 34.700703] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 34.700712] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 34.701026] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042
MB)
[ 34.701191] sd 0:0:0:0: [sda] Write Protect is off
[ 34.701350] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 34.701358] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 34.701651] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
next prev parent reply other threads:[~2007-12-07 13:32 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-11-02 18:34 Hemmann, Volker Armin
2007-11-07 6:15 ` Andrew Morton
2007-11-12 13:28 ` Tejun Heo
2007-12-07 13:32 ` Hemmann, Volker Armin [this message]
2007-12-07 23:20 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200712071432.08699.volker.armin.hemmann@tu-clausthal.de \
--to=volker.armin.hemmann@tu-clausthal.de \
--cc=akpm@linux-foundation.org \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®