From: Rasmus Andersen <rasmus@avlebavle.dk>
To: linux-kernel@vger.kernel.org
Subject: Help with intrepeting SATA log messages
Date: Sat, 19 Jan 2008 13:17:15 +0100 [thread overview]
Message-ID: <20080119121715.GA6860@avlebavle.dk> (raw)
Hello,
I was hoping that you could help me interpret these SATA errors from my
brand new Western Digital disk (at end). Also, this disk seems to refuse
smart commands:
# smartctl -s on -o on -S on /dev/sda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce
Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
Error SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Values from ATA status return descriptor are:
00 09 0c 00 00 00 00 00 00 00 00 00 00 00 50
A mandatory SMART command failed: exiting. To continue, add one or more
'-T permissive' options.
Whats up with that? :)
Thanks in advance,
Rasmus
md: recovery of RAID array md0
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
md: using 128k window, over a total of 198306240 blocks.
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:3f:aa:0b/00:03:01:00:00/e0 tag 0 cdb 0x0 data 393216 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:3f:aa:0b/00:03:01:00:00/e0 tag 0 cdb 0x0 data 393216 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:3f:aa:0b/00:03:01:00:00/e0 tag 0 cdb 0x0 data 393216 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:3f:aa:0b/00:03:01:00:00/e0 tag 0 cdb 0x0 data 393216 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:3f:aa:0b/00:03:01:00:00/e0 tag 0 cdb 0x0 data 393216 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:3f:aa:0b/00:03:01:00:00/e0 tag 0 cdb 0x0 data 393216 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 00 00 01
sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
end_request: I/O error, dev sda, sector 17541695
ata1: EH complete
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:bf:ad:0b/00:04:01:00:00/e0 tag 0 cdb 0x0 data 524288 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:bf:ad:0b/00:04:01:00:00/e0 tag 0 cdb 0x0 data 524288 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:bf:ad:0b/00:04:01:00:00/e0 tag 0 cdb 0x0 data 524288 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:bf:ad:0b/00:04:01:00:00/e0 tag 0 cdb 0x0 data 524288 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:bf:ad:0b/00:04:01:00:00/e0 tag 0 cdb 0x0 data 524288 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:bf:ad:0b/00:04:01:00:00/e0 tag 0 cdb 0x0 data 524288 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 00 00 01
sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
end_request: I/O error, dev sda, sector 17542591
ata1: EH complete
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:bf:b5:0b/00:04:01:00:00/e0 tag 0 cdb 0x0 data 524288 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:bf:b5:0b/00:04:01:00:00/e0 tag 0 cdb 0x0 data 524288 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:bf:b5:0b/00:04:01:00:00/e0 tag 0 cdb 0x0 data 524288 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:bf:b5:0b/00:04:01:00:00/e0 tag 0 cdb 0x0 data 524288 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:bf:b5:0b/00:04:01:00:00/e0 tag 0 cdb 0x0 data 524288 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd 25/00:00:bf:b5:0b/00:04:01:00:00/e0 tag 0 cdb 0x0 data 524288 in
res 51/00:00:01:00:00/00:00:01:00:00/e0 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 00 00 01
sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
end_request: I/O error, dev sda, sector 17544639
ata1: EH complete
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:cf:ab:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:cf:ab:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:cf:ab:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:cf:ab:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:cf:ab:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:cf:ab:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 00 00 01
sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
end_request: I/O error, dev sda, sector 17542095
ata1: EH complete
raid1: sda: unrecoverable I/O read error for block 17542016
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:17:b1:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:17:b1:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:17:b1:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:17:b1:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:17:b1:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:17:b1:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 00 00 01
sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
end_request: I/O error, dev sda, sector 17543447
ata1: EH complete
raid1: sda: unrecoverable I/O read error for block 17543296
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:5f:b6:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:5f:b6:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:5f:b6:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:5f:b6:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:5f:b6:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: (BMDMA2 stat 0x181ca109)
ata1.00: cmd c8/00:08:5f:b6:0b/00:00:00:00:00/e1 tag 0 cdb 0x0 data 4096 in
res 51/00:00:01:00:00/00:00:01:00:00/e1 Emask 0x1 (device error)
ata1.00: configured for UDMA/33
sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
01 00 00 01
sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
end_request: I/O error, dev sda, sector 17544799
ata1: EH complete
raid1: sda: unrecoverable I/O read error for block 17544704
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
md: md0: recovery done.
RAID1 conf printout:
--- wd:1 rd:2
disk 0, wo:1, o:1, dev:sdb1
disk 1, wo:0, o:1, dev:sda1
RAID1 conf printout:
--- wd:1 rd:2
disk 1, wo:0, o:1, dev:sda1
RAID1 conf printout:
--- wd:1 rd:2
disk 0, wo:1, o:1, dev:sdb1
disk 1, wo:0, o:1, dev:sda1
md: recovery of RAID array md0
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
md: using 128k window, over a total of 198306240 blocks.
reply other threads:[~2008-01-19 12:22 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20080119121715.GA6860@avlebavle.dk \
--to=rasmus@avlebavle.dk \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®