Hello, Summary: additional serial ports on MS9830 board do not work Keywords: serial Kernel version: 2.6.35.4 I have problems with the IRQs of a MS9830 Mini ITX board. The board has 1 serial port on a DB9 connector and 4 additional ones on internal connectors, which can also be powered. The computer has a touchscreen controller connected to one of those internal ports. The internal ports seem to be special as they don't work correctly. Depending on BIOS settings, I either don't get any IRQs from them or I get IRQs but the serial driver doesn't claim them. To make the bug hunt simpler, I disabled all ports but one of the internal ones, which I've set to 0x3F8/IRQ4. Then I open the port with "od /dev/ttyS0" and touch the screen. After some seconds I get <3>irq 4: nobody cared (try booting with the "irqpoll" option) <4>Pid: 3923, comm: exe Not tainted 2.6.35.4 #1 <4>Call Trace: <4> [] __report_bad_irq+0x2e/0x6f <4> [] note_interrupt+0xf0/0x147 <4> [] handle_level_irq+0x6d/0x99 <4> [] handle_irq+0x1a/0x20 <4> [] do_IRQ+0x33/0x75 <4> [] common_interrupt+0x29/0x30 <4> [] ? __do_softirq+0x34/0xca <4> [] do_softirq+0x25/0x2a <4> [] irq_exit+0x28/0x57 <4> [] do_IRQ+0x60/0x75 <4> [] common_interrupt+0x29/0x30 <4> [] ? timecompare_offset+0x9c/0x2c6 <4> [] ? __setup_irq+0x1d8/0x259 <4> [] request_threaded_irq+0xa3/0xd0 <4> [] ? serial8250_interrupt+0x0/0xb2 <4> [] serial8250_startup+0x3f5/0x53d <4> [] uart_startup+0x6e/0x101 <4> [] uart_open+0xff/0x2ac <4> [] ? tty_init_dev+0xb7/0xf0 <4> [] tty_open+0x28b/0x354 <4> [] chrdev_open+0xc0/0xd7 <4> [] __dentry_open+0xd1/0x1a7 <4> [] nameidata_to_filp+0x29/0x3d <4> [] ? chrdev_open+0x0/0xd7 <4> [] do_last+0x3d1/0x4d1 <4> [] do_filp_open+0x17c/0x41e <4> [] ? do_page_fault+0x2a1/0x2cf <4> [] do_sys_open+0x48/0x116 <4> [] sys_open+0x1e/0x26 <4> [] sysenter_do_call+0x12/0x26 <3>handlers: <3>[] (serial8250_interrupt+0x0/0xb2) <0>Disabling IRQ #4 <4>ttyS0: 1 input overrun(s) <6>usb 4-1: new full speed USB device using uhci_hcd and address 2 <4>ttyS0: 10 input overrun(s) in dmesg and some data from the touch controller. But it's very jumpy without interrupts, hardly useable. I tried the suggested option "irqpoll", but then the computer just freezes when I do "od /dev/ttyS0" and touch the screen. No kernel panic, just a hard freeze. I tried "acpi=noirq", "acpi=off" and disabling the APIC in the BIOS setup, too. None of these made the serial irq work. Can you give me any useful pointers what to try next? Kernel configuration is attached. Kind regards Jan