From: Mika Westerberg <mika.westerberg@linux.intel.com>
To: H Hartley Sweeten <hartleys@visionengravers.com>
Cc: Linux Kernel <linux-kernel@vger.kernel.org>,
linux-watchdog@vger.kernel.org, wim@iguana.be
Subject: Re: [RFC PATCH] watchdog: ep93xx: Use the WatchDog Timer Driver Core.
Date: Tue, 2 Aug 2011 12:16:40 +0300 [thread overview]
Message-ID: <20110802091640.GF13218@intel.com> (raw)
In-Reply-To: <201108011357.24745.hartleys@visionengravers.com>
On Mon, Aug 01, 2011 at 01:57:24PM -0700, H Hartley Sweeten wrote:
> Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
> Cc: Wim Van Sebroeck <wim@iguana.be> (maintainer:WATCHDOG DEVICE D...)
Nice. I'll try to test the patch later today.
I have few minor comments, see below.
>
> ---
>
> diff --git a/drivers/watchdog/ep93xx_wdt.c b/drivers/watchdog/ep93xx_wdt.c
> index 726b7df..bb97351 100644
> --- a/drivers/watchdog/ep93xx_wdt.c
> +++ b/drivers/watchdog/ep93xx_wdt.c
> @@ -24,11 +24,9 @@
> */
>
> #include <linux/module.h>
> -#include <linux/fs.h>
> #include <linux/miscdevice.h>
Is the above header still needed?
> #include <linux/watchdog.h>
> #include <linux/timer.h>
> -#include <linux/uaccess.h>
> #include <linux/io.h>
> #include <mach/hardware.h>
>
> @@ -39,15 +37,17 @@
> #define WDT_TIMEOUT 30
>
> static int nowayout = WATCHDOG_NOWAYOUT;
> +module_param(nowayout, int, 0);
> +MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started");
> +
> static int timeout = WDT_TIMEOUT;
> +module_param(timeout, int, 0);
> +MODULE_PARM_DESC(timeout,
> + "Watchdog timeout in seconds. (1<=timeout<=3600, default="
> + __MODULE_STRING(WDT_TIMEOUT) ")");
>
> static struct timer_list timer;
> static unsigned long next_heartbeat;
> -static unsigned long wdt_status;
> -static unsigned long boot_status;
> -
> -#define WDT_IN_USE 0
> -#define WDT_OK_TO_CLOSE 1
>
> #define EP93XX_WDT_REG(x) (EP93XX_WATCHDOG_BASE + (x))
> #define EP93XX_WDT_WATCHDOG EP93XX_WDT_REG(0x00)
> @@ -71,130 +71,46 @@ static inline void wdt_ping(void)
> __raw_writew(0x5555, EP93XX_WDT_WATCHDOG);
> }
>
> -static void wdt_startup(void)
> +static int void ep93xx_wdt_start(struct watchdog_device *wdd)
^^^^
extra 'void' above
> {
> - next_heartbeat = jiffies + (timeout * HZ);
> + next_heartbeat = jiffies + (wdd->timeout * HZ);
>
> wdt_enable();
> mod_timer(&timer, jiffies + WDT_INTERVAL);
> + return 0;
> }
>
> -static void wdt_shutdown(void)
> +static int ep93xx_wdt_stop(struct watchdog_device *wdd)
> {
> del_timer_sync(&timer);
> wdt_disable();
> + return 0;
> }
>
> -static void wdt_keepalive(void)
> +static int ep93xx_wdt_keepalive(struct watchdog_device *wdd)
> {
> /* user land ping */
> - next_heartbeat = jiffies + (timeout * HZ);
> -}
> -
> -static int ep93xx_wdt_open(struct inode *inode, struct file *file)
> -{
> - if (test_and_set_bit(WDT_IN_USE, &wdt_status))
> - return -EBUSY;
> -
> - clear_bit(WDT_OK_TO_CLOSE, &wdt_status);
> -
> - wdt_startup();
> -
> - return nonseekable_open(inode, file);
> -}
> -
> -static ssize_t
> -ep93xx_wdt_write(struct file *file, const char __user *data, size_t len,
> - loff_t *ppos)
> -{
> - if (len) {
> - if (!nowayout) {
> - size_t i;
> -
> - clear_bit(WDT_OK_TO_CLOSE, &wdt_status);
> -
> - for (i = 0; i != len; i++) {
> - char c;
> -
> - if (get_user(c, data + i))
> - return -EFAULT;
> -
> - if (c == 'V')
> - set_bit(WDT_OK_TO_CLOSE, &wdt_status);
> - else
> - clear_bit(WDT_OK_TO_CLOSE, &wdt_status);
> - }
> - }
> - wdt_keepalive();
> - }
> -
> - return len;
> + next_heartbeat = jiffies + (wdd->timeout * HZ);
> + return 0;
> }
>
> -static const struct watchdog_info ident = {
> - .options = WDIOF_CARDRESET | WDIOF_MAGICCLOSE,
> - .identity = "EP93xx Watchdog",
> +static const struct watchdog_info ep93xx_wdt_ident = {
> + .options = WDIOF_CARDRESET | WDIOF_MAGICCLOSE,
> + .identity = "EP93xx Watchdog",
> };
>
> -static long ep93xx_wdt_ioctl(struct file *file,
> - unsigned int cmd, unsigned long arg)
> -{
> - int ret = -ENOTTY;
> -
> - switch (cmd) {
> - case WDIOC_GETSUPPORT:
> - ret = copy_to_user((struct watchdog_info __user *)arg, &ident,
> - sizeof(ident)) ? -EFAULT : 0;
> - break;
> -
> - case WDIOC_GETSTATUS:
> - ret = put_user(0, (int __user *)arg);
> - break;
> -
> - case WDIOC_GETBOOTSTATUS:
> - ret = put_user(boot_status, (int __user *)arg);
> - break;
> -
> - case WDIOC_KEEPALIVE:
> - wdt_keepalive();
> - ret = 0;
> - break;
> -
> - case WDIOC_GETTIMEOUT:
> - /* actually, it is 0.250 seconds.... */
> - ret = put_user(1, (int __user *)arg);
> - break;
> - }
> - return ret;
> -}
> -
> -static int ep93xx_wdt_release(struct inode *inode, struct file *file)
> -{
> - if (test_bit(WDT_OK_TO_CLOSE, &wdt_status))
> - wdt_shutdown();
> - else
> - printk(KERN_CRIT PFX
> - "Device closed unexpectedly - timer will not stop\n");
> -
> - clear_bit(WDT_IN_USE, &wdt_status);
> - clear_bit(WDT_OK_TO_CLOSE, &wdt_status);
> -
> - return 0;
> -}
> -
> -static const struct file_operations ep93xx_wdt_fops = {
> +static const struct watchdog_ops ep93xx_wdt_ops = {
> .owner = THIS_MODULE,
> - .write = ep93xx_wdt_write,
> - .unlocked_ioctl = ep93xx_wdt_ioctl,
> - .open = ep93xx_wdt_open,
> - .release = ep93xx_wdt_release,
> - .llseek = no_llseek,
> + .start = ep93xx_wdt_start,
> + .stop = ep93xx_wdt_stop,
> + .ping = ep93xx_wdt_keepalive,
> };
>
> -static struct miscdevice ep93xx_wdt_miscdev = {
> - .minor = WATCHDOG_MINOR,
> - .name = "watchdog",
> - .fops = &ep93xx_wdt_fops,
> +static struct watchdog_device ep93xx_wdd = {
> + .info = &ep93xx_wdt_ident,
> + .ops = &ep93xx_wdt_ops,
> + .min_timeout = 1,
> + .max_timeout = 3600,
> };
>
> static void ep93xx_timer_ping(unsigned long data)
> @@ -210,43 +126,31 @@ static int __init ep93xx_wdt_init(void)
> {
> int err;
>
> - err = misc_register(&ep93xx_wdt_miscdev);
> + ep93xx_wdd.bootstatus = readl(EP93XX_WDT_WATCHDOG);
> + ep93xx_wdd.timeout = timeout;
Should you check that the given timeout is in valid range here, like it is
done in the original driver?
> +
> + err = watchdog_register_device(&ep93xx_wdd);
> + if (err)
> + return err;
>
> - boot_status = __raw_readl(EP93XX_WDT_WATCHDOG) & 0x01 ? 1 : 0;
> + setup_timer(&timer, ep93xx_timer_ping, 1);
>
> printk(KERN_INFO PFX "EP93XX watchdog, driver version "
> WDT_VERSION "%s\n",
> - (__raw_readl(EP93XX_WDT_WATCHDOG) & 0x08)
> + (ep93xx_wdd.bootstatus & 0x08)
> ? " (nCS1 disable detected)" : "");
>
> - if (timeout < 1 || timeout > 3600) {
> - timeout = WDT_TIMEOUT;
> - printk(KERN_INFO PFX
> - "timeout value must be 1<=x<=3600, using %d\n",
> - timeout);
> - }
> -
> - setup_timer(&timer, ep93xx_timer_ping, 1);
> - return err;
> + return 0;
> }
> +module_init(ep93xx_wdt_init);
>
> static void __exit ep93xx_wdt_exit(void)
> {
> - wdt_shutdown();
> - misc_deregister(&ep93xx_wdt_miscdev);
> + wdt_shutdown(&ep93xx_wdd);
ep93xx_wdt_stop(&ep93xx_wdd);
> + watchdog_unregister_device(&ep93xx_wdd);
> }
> -
> -module_init(ep93xx_wdt_init);
> module_exit(ep93xx_wdt_exit);
>
> -module_param(nowayout, int, 0);
> -MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started");
> -
> -module_param(timeout, int, 0);
> -MODULE_PARM_DESC(timeout,
> - "Watchdog timeout in seconds. (1<=timeout<=3600, default="
> - __MODULE_STRING(WDT_TIMEOUT) ")");
> -
> MODULE_AUTHOR("Ray Lehtiniemi <rayl@mail.com>,"
> "Alessandro Zummo <a.zummo@towertech.it>");
> MODULE_DESCRIPTION("EP93xx Watchdog");
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
next prev parent reply other threads:[~2011-08-02 9:16 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-08-01 20:57 H Hartley Sweeten
2011-08-02 9:16 ` Mika Westerberg [this message]
2011-08-02 16:55 ` H Hartley Sweeten
2011-08-03 8:15 ` Mika Westerberg
2011-08-03 16:22 ` H Hartley Sweeten
2011-08-03 9:56 ` Wim Van Sebroeck
2011-08-02 9:57 ` Wim Van Sebroeck
2011-08-02 17:02 ` H Hartley Sweeten
2011-08-03 10:07 ` Wim Van Sebroeck
2011-08-03 16:34 ` H Hartley Sweeten
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20110802091640.GF13218@intel.com \
--to=mika.westerberg@linux.intel.com \
--cc=hartleys@visionengravers.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-watchdog@vger.kernel.org \
--cc=wim@iguana.be \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®